Cambrionix SyncPad54 Port Large Capacity Data Duplicator User Manual
- June 16, 2024
- Cambrionix
Table of Contents
- Cambrionix SyncPad54 Port Large Capacity Data Duplicator
- Your SyncPad54 at a glance
- Safety
- Getting Started
- Product Specifications
- Troubleshooting
- Disposal
- Returns and Damaged Products
- Compliance and Standards
- Terms and Conditions
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Cambrionix SyncPad54 Port Large Capacity Data Duplicator
Your SyncPad54 at a glance
The SyncPad54 has been designed primarily for desktop use, being highly compact and quiet. It provides 2.5W of charging power to each of its USB 2.0 Type-A ports, allowing mobile devices to be charged quickly, safely and reliably. All ports can be controlled using Cambrionix software to enable charging and data transfer while monitoring important port and device information. The SyncPad54 can charge attached USB devices without using a local computer, and our intelligent charging algorithm allows almost any device to be charged at its optimum rate (up to 0.5A). The firmware can be updated to enable new charging profiles, ensuring the SyncPad54 can charge the latest devices. It is ready to charge out-of-the-box and sync devices when attached to a host computer. When a local (host) computer is connected, the host can control the operation of the ports using available software. Device charging and synchronisation can be monitored through Cambrionix’s LiveViewer App, the Application Programming Interface (API) or the Command Line Interface (CLI). Cambrionix’s free monitoring and control software can be downloaded fro www.cambrionix.com/software For the SyncPad54, a host will need to be connected to the hub before initial charging will take place; once the hub is up and running, you will not need a host connected unless you power cycle the hub, in which case a host will need to be connected for the initial power-up. You can download the latest version of this manual and all product user manuals from our website at the following link. www.cambrionix.com/product-user-manuals
Key Features
Transfer Data Seamlessly
Each high-speed port can transfer data up to Maximum downstream speedGbps
Power
Each port can charge devices up to 0.5A (2.5W)
Scalability
Up to 54 devices can be connected at once using multiple hubs
Safety
This user manual is for informational purposes only, it contains information
for the start-up and operation of this product. Note: the contents and the
product described are subject to change without notice. To avoid injuries and
damage, observe the safety instructions in the user manual.
This manual has been arranged to follow the IEC/ICEE 82079-1 standard. This is
to facilitate the easier understanding and location of information relating to
the SyncPad54. Any errors or omissions can be reported using our support
ticket system (seeHelp and Support). This way, any issues that are discovered
can be acted on quickly and we can update the documentation to reflect this.
Understanding and observing the instructions in this user manual are
prerequisites for hazard-free use and safety during operation. This user
manual cannot cover all possible applications. If you would like additional
information or if problems arise that are not sufficiently addressed in this
manual, please ask your distributor or contact us directly using the means
preferred, which are located on the back cover of this manual.
CAUTION
- Personal Injury and Damage to the Product
- Always observe the safety instructions in this user manual
Signal word panel
Depending on the probability of serious consequences, potential dangers are
identified with a signal word, the corresponding safety colour, and if
appropriate, the safety alert symbol.
CAUTION
Indicates a potentially hazardous situation that, if not avoided, may
result in moderate or minor (reversible) injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may
result in damage to the product and its functions, or to property in its
proximity.
Safety alert symbol
- Use of the safety alert symbol indicates a risk of injury. Observe all measures that are marked with the safety alert symbol in order to avoid injury
Pictograms
These symbols will be used throughout this documentation to alert to any
potential dangers or any actions that must be taken.
Product modification
Cambrionix products are designed and manufactured to meet the requirements of
UK and international safety regulations. Modifications to the product could
affect safety and render the product non-compliant with relevant safety
standards, resulting in injury or damage to the product.
CAUTION
- An electric shock or personal injury may occur
- Do not modify the product in any way. Do not dismantle the product. Do not open the product
CAUTION
- Fire, or personal injury may occur
- Do not obstruct air vents on the product. Do not cover the product in or place near combustible material.
CAUTION
- Damage to your product may occur
- Do not bend or compress any part of the product.
Power supply
This section describes the safety precautions you must follow when using the
external power supply.
CAUTION
An electric shock or personal injury may occur Do not use a damaged power
cord or plug, or a loose power socket. Do not touch the power plug with wet
hands. Do not allow liquids to come into contact with the unit or power
supply.
CAUTION
Damage to your product may occur Do not short circuit the Power Supply Unit (PSU) supplied with your product. Do not disconnect the power cord while the product is being used. Do not bend or pull the power cord with excessive force. Do not use a power supply that exceeds the power supply specifications within this manual
Storage and Installation
This section describes safety precautions you must follow when installing and
storing your SyncPad54.
CAUTION
- Damage to your Cambrionix product may occur
- Operate the product only in an environment where the ambient temperature is inside the operating temperature range. Operate the product only in an environment where the relative humidity is inside the operating range. Be careful not to leave the power cord underneath a heavy object.
CAUTION
- Overheated power sockets may cause a fire
- Do not overload the power socket that your hub is connected to. Insert the power plug all the way into the socket so that it is not loose.
CAUTION
- Overloading the brackets may cause failure
- The rack brackets for all our products are not designed to be used in a mobile application, bracket failure could occur if the units are not supported fully e.g Shock during road transport.
Getting Started
This manual provides a reference for end-users installing for the first time and using their hub afterwards. As well as a guide for product safety-related information. The SyncPad54 is intended to be used in an indoor static environment in which the environment falls within the tested specifications to provide charge, sync and management functionality. Please see the physical specifications section of this manual for information on the environment specifications.
Unpacking your product
When you have received your product, please check the packing slip inside the
box to ensure all contents and quantities are correct before opening. This is
to avoid retesting and repackaging any items that are not required. When
opening the packaging, use a suitable method to open the box i.e, do not use a
knife. This is to ensure the product is not damaged.
CAUTION
- Personal Injury and Damage to the product
- There will be a label on the hub advising you to read the User manual before use. This will need to be removed before use as it may be covering host ports, vents etc.
What’s Included
- USB 2.0 Type-B Cable (to provide communication between the host system and hub)
- SyncPad54 Hub
- 2m Mains power cable (Country specified on order including fuse for the UK plugs)
- Power Supply Unit
Part description| Part number
---|---
USB 2.0 Type-B updater cable| 200499
Power Supply Unit| 200421
Part description| Part number
---|---
UK Power cable| 200144
US Power cable| 200327
EU Power cable| 200329
Part description| Part number
---|---
AUS Power cable| 200337
IND Power cable| 200341
Connecting to the mains
Connect the Power Supply Unit (PSU) to the hub using the 4-pin Mini-DIN plug.
Connect the power cable to the PSU. Make sure you adhere to local safety
regulations, connect the power cable to the 100 – 250 VAC mains power outlet
and switch the hub on using the small power switch located adjacent to the
power input connector on the hub. When the device is switched on, a red LED
next to the power input will be illuminated. The hub is now ready to charge
attached devices. Periodic inspections should be made to power supply cables
and any USB cables for any signs of damage. If any damage is found, replace
the damaged cord before further use.
Connecting to a Host
Once the power is connected, connect the SyncPad54 to your host system using a
USB 2.0 Type-B cable. Using an incorrect host cable may result in the hub and
all subsequent ports not being recognised by your host. Please note that USB
specifications require a minimum 100 mA charge current to be available during
data transfer. As indicated in above, if the attached device has a BC1.2
compliant CDP port, the device can draw up to 0.5A whilst transferring data.
Charging
Your SyncPad54 will allow your device to charge at the maximum rate possible
up to 0.5A. The way that charging takes place is the SyncPad54 will provide
the device with a capability to charge and the device’s USB charging
controller will determine the maximum amount of charge it wants to draw down.
Although a maximum charge rate of 0.5A is possible, the device itself
determines the exact rate and as such you may not see the maximum amount of
charging on every device type that is connected.
Cables
Some USB cables are for data transfer only, and some are for power delivery
only. Some options can handle both tasks. Be sure to verify a cable’s
abilities before purchasing it and select a cable that can handle the speeds
and power transfer that you require. We would advise using the cable that was
provided with the device to connect to our hubs.
Registration
You may register your product at www.cambrionix.com/product-
registration
Help and Support
FAQs and help can be found on the Help page here
-
www.cambrionix.com/help_pages/help.
You can raise a support ticket for more in depth support here -
https://cambrionix.atlassian.net/servicedesk/customer/portals
You can also download any of our manuals and keep up to date at the link here
When contacting support, please supply the product information for the hub in question. This can be found on the Device Information Plate which is either on the underside or back of the unit. Providing serial and Purchase order numbers can help identify your specific product and speed up the process.
Using your SyncPad54
In this section, you can find information using your hub in charge or sync
application. You can also find information on managing your hub, changing port
modes, connecting multiple hubs to one host and using Cambrionix Software.
Fan Behaviour
Your SyncPad54 has an inbuilt fan used to cool the product when internal
temperatures rise above a set threshold. On power up the fan will spin for
approximately a second before turning off. The temperature at which the fan
should begin to cool the device is 60 °C, the fan will be at max speed when
the internal temperature reaches 80. Once the SyncPad54 is below the internal
temperature of 60 the fan will switch off.
Using without connecting to a host
When the Hub is switched on and is not connected to a local host computer it
is automatically configured to charge devices using its intelligent charging
algorithm. Connect the devices to be charged to any of the available ports
(not the Host Port) using USB-compliant cables. Once the devices are
connected, the algorithm will detect the highest charge rate allowable for
each attached device. Charging at the optimum rate (up to 0.5A) specified by
the manufacturer will commence once profiling is complete. Depending on the
state of charge of the device attached, this may take tens of seconds. For the
SyncPad54, a host will need to be connected to the hub before initial charging
will take place; once the hub is up and running, you will not need a host
connected unless you power cycle the hub, in which case a host will need to be
connected for the initial power-up.
Using when connected to a host
Connecting the Hub to a host computer
Connect the SyncPad54 to your host system using a USB 2.0 Type-B cable. Using
an incorrect host cable may result in the hub and all subsequent ports not
being recognised by your host.
Charging
When the Host Port is connected to a local computer, the hub defaults to Sync
mode and charge currents are determined according to USB Implementers Forum
(USBIF) Super-Speed USB3 specifications. If the attached device complies with
USB-IF Battery Charging specification BC1.2 and supports Charging Downstream
Port (CDP), the hub can provide high-speed charging at 1.5A. If the connected
device does not comply with BC1.2, the charge current will be limited to 500
mA in compliance with USB specifications. If you wish to limit the charging to
your devices whilst connected to your host system then you can disable CDP.
You can disable CDP through Internal hub settings either by going through the
advanced settings and turning “Sync charge” off or through the API and
disabling it via code. For example, the instructions would be below using the
command line. The CLI commands for turning off the sync charge options, with a
1 or 0 per port.
This can also be done via the API if this is easier. Just supply that string (joined with \n) like:
Note that settings_reset clears any previous settings, so if you need to retain something else, it would be better to issue settings_display first, which gives you the entire settings which you can then modify and re-issue in entirety.
Data Transfer
If you wish to transfer data, change applications, restore or update your
mobile device, a data connection to a local host computer is required. The
Cambrionix API and software is compatible with macOS®, Windows™ and Linux®
operating systems and can transfer data between these operating systems and
many mobile operating systems such as iOS™ and Android™. In order to transfer
data, connect the host port to your local (host) computer using a USB 2.0
Type-B compliant cable. Any devices connected to the hub will now appear as if
they were connected to the host computer’s USB port.
Communication Interface and Protocol
The SyncPad54 appears as a virtual COM port (VCP). On Microsoft Windows™, the
system will appear as a COM port, the COM port number can be found in device
manager. On macOS®, a device file is created in the / directory. S is an
alpha-numeric serial string unique to each device
Devices incorporate a USB to UART converter IC from FTDI International. On Windows 7 or later, a driver may automatically be installed (if Windows is configured to download drivers from the internet automatically). If this is not the case, or if a Mac® or Linux® platform is used, the driver may be downloaded from www.ftdichip.com. The VCP drivers are required. For Linux® or Mac computers, the default OS drivers should be used. The default communications settings are as below, ANSI terminal emulation should be selected.
Communication setting | Value |
---|---|
Number of bits per second (baud) | 115200 |
Number of data bits | 8 |
Communication setting | Value |
--- | --- |
Parity | None |
Number of stop bits | 1 |
Flow control | None |
Cleaning your SyncPad54
Cleaning the product is generally not required, although in some instances
it may be necessary if excess dirt/ dust/ hair has accumulated, or if minor
liquid spillages have occurred on the module during operation or storage.
CAUTION
An electric shock or personal injury may occur If there is dirt/ spillage over
a ventilation slot, external data/ power connector or product aperture, please
remove power from the unit without touching the liquid and seek advise before
reapplying power
- Ensure that the product is switched off and the power cord is removed from the product. Hold the power cable by the plug and do not touch either the plug or the power cord with wet or damp hands as an electrical shock may result
- Wipe the product with a clean, dry and soft cloth. Do not use detergents that contain alcohol, solvent or surface-active agents. Do not spray water or detergent directly onto the product
- Mildly dampen a soft and dry cloth in water and wring thoroughly to clean the product as required
- Dry the product thoroughly once the cleaning has finished
- Reconnect the power cord and use your product as advised once cleaning is complete
Product Specifications
The SyncPad54 is manufactured in the UK
Input Power Requirements
Input Voltage (V) | 12 |
---|---|
Input Current (A) | 13 |
Input Connector | 4-Pin Mini-DIN |
Output Power
Output Voltage (V) | 5 |
---|---|
Output Voltage Tolerance (%) | +/-5 |
Output Current, Max per Port (A) | 0.5 |
Output Power, Max per Port (W) | 2.5 |
Output Power, Total (W) | 160 |
Rail value limits
Physical specifications
Upstream connector type | USB 2.0 Type-B |
---|---|
Downstream connector type | USB 2.0 Type-A |
Maximum Downstream Data Speed per Port (Gbps) | Maximum downstream speed |
Ambient Operating Temperature range °C | 0-35 |
Relative, non-condensing, humidity operating range (%) | 5 – 95 |
Dimensions WxDxH (mm) | 430 x 86 x 28 |
Weight (kg) | 1.5 |
Number of Downstream ports | 54 |
Ports Lifetime
Standard USB connections have a minimum rated lifetime of 1,500 cycles of
insertion and removal. USB-C receptacles have a minimum rated lifetime of
10,000 cycles of insertion and removal. This is an industry-standard.One thing
you can do to prolong the lifetime of the ports on your SyncPad54 is to use
“sacrificial cables” in between the hub and your charging cables so when you
repeatedly connect/ disconnect you are only going to wear the cables rather
than the hub.
Consumables and Placing Orders
Below is a list of any Consumable products you may require for your SyncPad54
including the cables you will require to connect devices to the hub.
- Cables USB 2.0 Type-A
If you require any spare parts, such as the power cable or USB 2.0 Type-B cable, these can be ordered by quoting the product part number and the spare part number (available from the Getting Started section). These can be ordered from the reseller or solution partner you purchased your SyncPad54 from, or from Cambrionix directly. To find one of our partners local to you please visit www.cambrionix.com/partners where you can learn about the local vendors and distributors that can assist you and find their contact information.
Power Supply
Input Voltage (V) | 100-240 |
---|---|
Input Current @ 115VAC (A) | 4 |
Input Current @ 230VAC (A) | 2 |
Input Frequency (Hz) | 50-60 |
Input Connector | C14 |
Output Voltage, Max (V) | 12 |
Output Current, Max (A) | 15 |
Output Power, Max (W) | 180 |
Output Connector | 4-Pin Mini-DIN |
Dimensions WxDxH (mm) | 210 x 85 x 46 |
- -V is connected to AC input ground.
Troubleshooting
If you experience any issues with your SyncPad54; please try the following troubleshooting steps, if the issue is not addressed in this section, please get in touch with your local vendor or Cambrionix. To contact Cambrionix Support please see Help and Support.
Common troubleshooting tips
Some tips and information to check first.
- If you directly connect the same device to the port the hub is in, does it appear to the OS.
- If you plug a device (phone, USB stick) into the hub, does it appear to the OS (device manager/system info etc.).
- Try switching the cables with ones that are working/ use cable from a hub that is working.
Logging through LiveViewer
If you are experiencing a bug or an issue, we may ask you to obtain some logs
of the behaviour, to see in more detail what is happening. To get logs of the
behaviour use the following steps to get a zip file of the logs.
- Open LiveViewer (if this is not already downloaded, then go onto our website and download both the API and LiveViewer) www.cambrionix.com/software
- Once in LiveViewer, on the left-hand side of the screen, select the settings section.
- Once in the settings section, select the API tab.
- In the API section click the “cog” button on the right hand side of the local API
- Click the “select all” tick box and then the save button.
- After this is enabled, use the hub in a way that causes the issue you are seeing.
- Wait for the issue to occur, i.e. device disconnects.
- Make a note of the time and date that the issue occurs then go back to the API page in LiveViewer, and press the zip logs.
- Once you have the logs un-tick the “select all” box and save your settings.
- Send the logs to us for us to take a look at.
The API keeps a maximum of 20 logs at 256Mb each, so the latest one is usually smaller. If a crash occurs, you will see a smaller log file and the next instance of API shuffles the existing ones
Hardware Failure
If the Hardware fails the LEDs can flash in a pattern to determine the type of
failure. The power LED will flash the pattern if no LEDs are present on the
downstream ports. The unit will blink four times, followed by eight long or
short flashes, which then repeat. The flashes are a number in binary which
matches a number in our error code list. i.e if the LED flashes the following
– B SLSSSLSS, the binary number is 01000100.
Device connection
If you are seeing any device connection issues please read through the
following troubleshooting steps to see if this resolves the observed
behaviour.
Device issues when updating
We have found that during updates on some devices the connection can be
dropped or lost on the device, this is due to devices going in and out of the
bootloader and requiring different power levels. In most instances disabling
CDP and changing the ports to always be on has resolved this issue for our
customers. You can disable CDP through Internal hub settings either by going
through the advanced settings and turning “Sync charge” off or through the API
and disabling it via code. For example, the instructions would be below using
the command line.
You can set the ports to always be on through Internal hub settings through the advanced settings and turning “Ports On” settings to always on for each port. When you set the port to always be on you will need to set a default profile on each port for when the port(s). There is a desription for each profile within LiveViewer or Cambrionix Connect.
Unstable device connection
Some devices can have unstable connections with your host system through the
SyncPad54. We have only observed this behaviour in a very few amount of
devices, disabling CDP and setting the ports to always be on has resolved all
issues and the connections are stable. You can disable CDP through Internal
hub settings either by going through the advanced settings and turning “Sync
charge” off or through the API and disabling it via code. For example, using
the command line, the instructions would be as below.
You can set the ports to always be on through Internal hub settings through the advanced settings and turning “Ports On” settings to always on for each port. When you set the port to always be on you will need to set a default profile on each port for when the port(s). There is a description for each profile within LiveViewer or Cambrionix Connect.
Battery information for Android
If you are observing an issue displaying battery information on Android
devices ensure firstly you have the ADB tool installed and open then try these
things in order.
- Check that developer options are enabled on the Android device, and then that USB debugging is also enabled.
- If you have done this step and it still does not work, go to Developer Options and click ‘Revoke USB debugging authorisations’. Unplug the cable and reconnect.
- If this still doesn’t work, turn off the developer options at the top, re-enable it, and re-enable ‘USB Debugging’.
- You can get detailed info directly from ADB at each step to diagnose things:
Unknown devices
Sometimes, within Liveviewer and Device Manager, the connected device may show
up as an unknown device. This can be due to the host system needing to be
trusted on the device. This can be done on the device itself on the initial
connection. This could also be due to an insufficient number of endpoints
available on the USB controller in the host system. This limitation within the
USB controller can only be resolved if you connect fewer USB devices to the
controller in question. For Apple devices there is a setting called “USB
accessories” which can be activated, Once activated it will reduce the number
of times a device will need to be unlocked/ trusted. More information can be
found at the link https://support.apple.com/en-gb/HT208857.
Cannot connect any more devices
Sometimes, you may reach the endpoint limit of your USB controller and this
may stop you from being able to attach any more devices to your host system.
You can create more space is to change connections from USB3 to USB2. You can
change the connection by disabling USB3 in the BIOS on startup. A much simpler
way is to use USB2 cables instead of USB3 cables, limiting the connection to
USB2.
Hub connection issues
If there are issues with the hub and connecting to your host system, please
see below for troubleshooting solutions.
Hub not connecting to the host
If you see that the SyncPad54 is not connecting to the host system, one of the
issues may be caused by the USB drivers on your host system not being up to
date. It is good practice to ensure you have the latest drivers and updates
installed on your host system, which is usually handled by the OS, but
sometimes may require an update directly from the USB host controllers
manufacturer, which will be found on their website. USB drivers required are
FTDI drivers, which can be found on the site https://ftdichip.com/drivers/.
Cannot access the COM port
You may get an error message stating “COM (and then a number) could not be
opened (Access is denied)”. This is because an application has control over
the COM port that the hub is connected to, and no subsequent application can
access the hub. To resolve this, you will need to close any other applications
that are using the COM port before trying to use the COM port.
Using with a headless system
If you are using a headless system with no GUI, then and you require to enable
logging for support issues, you can use the following command to create the
logging cfg file manually:
Then after re-producing the problem, you can zip the logs from the folder
You may delete the file below when you are finished with it.
Software troubleshooting
Some users have noted that the API can cause a high level of CPU usage. This
can sometimes be linked to the API recorder service. If you are finding this
and you are not using it then we would recommend to uninstall it from your
system entirely. Information on how to uninstall programs can be found in the
Removing Software section.
Disposal
Disposal of Old Electrical & Electrical Equipment (Applicable in the European Union and other European countries with separate collection systems) This product is subject to Directive 2012/19/EU of the European Parliament and the Council of the European Union on the waste electrical and electronic equipment (WEEE), and in jurisdictions adopting that Directive, is marked as being put on the market after August 12, 2005, and should not be disposed of as unsorted municipal waste. Please utilize your local WEEE collection facilities in the disposition of this product and otherwise observe all applicable requirements.
- Cambrionix PRN (Producer Registration Number) For the UK is “WEE/BH191TT”.
Returns and Damaged Products
If you wish to return or fix a damaged product first look at the terms on our website www.cambrionix.com/terms-conditions Before a product is returned please contact support using the methods detailed in the Help and Support section.
What if my order arrives with an issue?
- If you have received your order in a damaged box and/or the product has physical damage please contact Cambrionix Customer Support or your distribution partner. Please provide photos of the damaged box and/or product when contacting Customer support.
- If an item in your order does not have physical damage but is not functioning properly or will not power on, please contact Customer Support or your distribution partner and provide as much information as possible and including any steps followed to troubleshoot internally.
- Please include photos of the damaged box and product when contacting Customer Support.
Note: If you have received your order in a damaged box and the damage was indicated to the courier, please provide us with a copy of the delivery note detailing this.
What happens after I have requested a Return?
- If you have not purchased the Product(s) direct from Cambrionix please contact the vendor the item was originally purchased from for their returns process.
- Once you have notified Cambrionix of your return, Cambrionix will arrange for the collection of the product(s), or provide instructions and details for you to return the product direct.
- When returning your product(s), please only send back the items that were advised through the support process.
- Return your product(s) in the original packaging where you can. Where original packaging is not available, use suitable packing methods, which will ensure that the product cannot be subject to impact damage. i.e. double-walled cardboard box with 50mm of soft material.
- Product(s) not returned in their original condition may result in additional costs, please refer to the warranty and terms section on our website.
- Where Cambrionix arranges collection, return shipping will be free, unless Cambrionix notified you otherwise.
- When contacting us about returning a product please provide the following information.
- Collection Address
- Weights and Dimensions WxDxH (m) of shipment
- Preferred collection date and time.
- Product serial number(s) (this can be found on a label on the rear or underside of the unit)
- Purchase order number(s)
Compliance and Standards
- CB Certificate
- CE Tested and marked
- FCC Part 15 Tested and marked
- Housed within a UL94-VO specification fire enclosure
- RoHS Compliant
- Independently safety tested by the Underwriters Laboratory (UL) under file #E346549
Terms and Conditions
The use of Cambrionix hubs is subject to the Cambrionix Terms and Conditions, the document can be downloaded and viewed using the following link. https://downloads.cambrionix.com/documentation/en/Cambrionix-Terms-and- Conditions.pdf
Use of Trademarks, Registered Trademarks, and other Pro-tected Names and Symbols
This manual may refer to trademarks, registered trademarks, and other protected names and or symbols of third-party companies not related in any way to Cambrionix. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by Cambrionix, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Cambrionix hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and /or symbols contained in this manual and related documents are the property of their respective holders “Mac® and macOS® are trademarks of Apple Inc., registered in the U.S. and other countries and regions.” “Intel® and the Intel logo are trademarks of Intel Corporation or its subsidiaries.” “Thunderbolt™ and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries.” “Android™ is a trademark of Google LLC” “Chromebook™ is a trademark of Google LLC.” “iOS™ is a trademark or registered trademark of Apple Inc,in the US and other countries and is used under license.” “Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries” “ Microsoft™ and Microsoft Windows™ are trademarks of the Microsoft group of companies.” “Cambrionix® and the logo are trademarks of Cambrionix Limited.”
Cambrionix Patents
Title
|
Link
| Application Number|
Grant Number
---|---|---|---
Syncing and Charging Port|
GB2489429|
1105081.2| 2489429
CAMBRIONIX| UK00002646615| 2646615| 00002646615
CAMBRIONIX VERY INTELLIGENT…|
|
2646617
|
00002646617
MOD IT DS|
GB2591233|
6089600| 6089600
MOD IT| eSearch| 007918669| 007918669
MOD IT| 90079186690001| 007918669-0001| 90079186690001
MOD IT| 90079186690002| 007918669-0002| 90079186690002
MOD IT| 90079186690003| 007918669-0003| 90079186690003
MOD IT| 90079186690004| 007918669-0004| 90079186690004
MOD IT| 90079186690005| 007918669-0005| 90079186690005
MOD IT| 90079186690006| 007918669-0006| 90079186690006
MOD IT| | 195761| 195761
MOD IT DS| | 30202007995X| 30202007995X
MOD IT MM| | 30202007994Y| 30202007994Y
MOD IT STACK| | 30202007993P| 30202007993P
MOD IT DS| 6077253| 6077253| 6077253
MOD IT DS|
3a2f8b88e935| 202012311| 202012311
MOD IT DS| | 195759| 195759
MOD IT DS| | 329440-001|
MOD IT DS| | 29/735,477| D936,001
MOD IT| 6077254|
6077254| 6077254
MOD IT MM| 6077255| 6077255| 6077255
MOD IT MM|
2a6ebe915fe9| 202012310| 202012310
MOD IT MM| | 195758|
MOD IT MM| | 329441-001|
Title
|
Link
| Application Number|
Grant Number
---|---|---|---
MOD IT MM| | 29/735,479|
MOD IT| 6077256|
6077256| 6077256
MOD IT STACK| 6077257| 6077257| 6077257
MOD IT STACK|
081a4b9c69eb| 202012312| 202012312
MOD IT STACK| | 29/735,475| D936,000
MOD IT DS LUGS| 6089601| 6089601| 6089601
MOD IT MM| 6089602| 6089602| 6089602
MOD IT DS LUGS| 6089603| 6089603| 6089603
MOD IT STACK| 6089604| 6089604| 6089604
MOD IT| 6089605|
6089605| 6089605
Cambrionix Limited The Maurice Wilkes Building Cowley Road Cambridge CB4 0DS United Kingdom
- +44 (0) 1223 755520
- enquiries@cambrionix.com
- www.cambrionix.com
Cambrionix Ltd is a company registered in England and Wales with the company number 06210854
References
- Cambrionix: USB Hub Experts - Smart Managed USB Hubs
- Help Home - Cambrionix
- Partners - Cambrionix
- Product Registration - Cambrionix
- Product User Manuals - Cambrionix
- Software - Manage Your Devices With Cambrionix Software
- Terms & Conditions - Cambrionix
- Home - FTDI
- Jira Service Management
- IP Australia | Australian Design Search
- IP Australia | Australian Design Search
- IP Australia | Australian Design Search
- Allow USB and other accessories to connect to your iPhone, iPad or iPod touch – Apple Support (UK)
- Terms & Conditions - Cambrionix
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
- Find a registered design - GOV.UK
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>