Novozopai 3 & Y Carplay Android Auto Instrument Cluster User Manual
- June 15, 2024
- Novozopai
Table of Contents
Dashboard Display
User Manual
Navigation Bar
Quickly locate the main panel
Swiping the right edge of the device screen to the left side, will pop up the
navigation bar. touching the icon will directly go to the panel.
By using the right steering wheel to roll up and down, the switching e!ect can also be triggered
Navigation Bar will hide automatically If there is no operation after 5
seconds
If the screen in power o!, touch the screen and hold 1 seconds to turn the
screen alive
Dashboard
Overview
Appearance
In the Setting > Appearance, We can choose “Day / Night / Auto” by select
“Auto”, system will match the style from your car
Volume & Brighteness
You can switch diferent status by Slide Up & Slide Down Left side control
volume, Right side control brighteness
Main Stage
You can switch diferent status by Slide Left & Slide Right Such as: Parked
(Frunk & Trunk & Door) / Driving / Tire Pressure
Phone Connection
Setting
Overview
Steering Wheel Roller CarPlay
In the General > Wheel Roller, When you trun it on, You can use Wheel button
to control the navigation of CarPlay
Steering Wheel can not work with Autopilot
Phone Connection Display Mode
In the Display > Split Screen , by choosing Full / Half to switch the screen
size for Phone Connection
OTA
Overview
In the Setting > Software, You can easily check your system version, using OTA
to get the latest update package, or swith to other theme as your favours.
Let’s Keep Your Dashboard Always Fresh & Safety
WE REALLY HOPE YOU CAN ENJOT IT!
Installation steps
1、Removal of the instrument panel (left side)| 2、Removal of the dashboard
(right side)| 3、Raise the instrument panel vertically upward from the left and
right sides
4、Remove the dashboard trim panel| 5、Plug the power cord into the 37th and
39nd holes counting from left to right, blind holes do not count in the count.
Insert the machine into the dashboard trim panel by aligning the holes|
6、Fixed mounting iron plate
7、Pry open the trim panel clips at the bottom of the glove box at the
passenger side| 8、Pull out the bottom flap of the glove box| 9、Unplug the gray
plug of the original car computer
10、Connect the unplugged computer plug B2 to the
instrument screen power cable B2 plug| 11、Connect the B1 end of the original
car computer to the instrument screen power cable B1 plug| 12、Wire interface
description diagram
13、After connecting A and A1, put it through the position pointed out by the
finger and fix the power cord with adhesive tape, which cannot block the
position of the snap| 14、Use tape to secure the power cable along the
dashboard recess, toward the steering wheel. This is
done to prevent rattling.| 15、Connect the dashboard trim panel with the
product installed to the power supply
16、After installing the trim panel, restore the front right A-pillar trim
panel to its original state| 17、Installation completed|
AMD Ryzen Chip
1、Removal of the instrument panel (left side)| 2、Removal of the dashboard
(right side)| 3、Raise the instrument panel vertically upward from the left and
right sides
4、Remove the dashboard trim panel| 5、Plug the power cord into the 37th and
39nd holes counting from left to right, blind holes do not count in the count.
Insert the machine into the dashboard trim panel by aligning the holes|
6、Fixed mounting iron plate
7、Remove the front right seat A-pillar flap| 8、Blue Protocol Interface A|
9、White power connector B
10、After unplugging the original power connector B, connect the female
connector to B1 and the male connector to B2| 11、The effect after the power
cord is connected is shown in the figure| 12、Wire interface description
diagram
13、Connect the blue protocol cable A1 to the original A connector| 14、After
connecting D and D1, put it through the position pointed out by the finger and
fix the power cord with adhesive tape, which cannot block the
position of the snap| 15、Use tape to secure the power cable along the
dashboard recess, toward the steering wheel.
This is done to prevent rattling
16、Connect the dashboard trim panel with the product installed to the power
supply| 17、After installing the trim panel, restore the front right A-pillar
trim panel to its original state| 18、Installation completed
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>