4K HDMI Wireless Transmitter/Receiver Manual and Pairing
- June 15, 2024
- HDMI
Table of Contents
50M 5.8G Wireless Wifi HDMI Extender Video Transmitter Receiver Adapter 1 To 4 1080P Screen Share Switch for PS4 DVD Camera PC
Note:TX=Transmitter;RX=Receiver;TX RX= Transmitter Receiver, the link have two version ,one is 1080P ,other is 4K.but the description is only for 4K Version ;
Transmission distance
1.Outdoor space 50m/660FT
2.No indoor wall penetrates 30m/164FT
3.Pass through the wall 5-15m /32-65FT
4.Upper and lower layers are better within 5m/32FT
Introduction:
The HDMI wireless extender provides an easy way to extend the HDMI signal in
open environments up to 50
meters
Characteristics:
1.This wireless HDMI extender consists of a transmitter unit and a receiver unit.
2.The transmitter supports loop output for easy monitoring.
3.Supports multiple resolutions, including 480i/576i to 4k@30hz(4K Version) or 1080P@60Hz(1080P Version).
4.Support 5G single frequency, fast transmission speed,strong anti- interference ability.
5.The external antenna supports long-distance transmission with a maximum air expansion environment of 50 meters (pay attention to ambient interference).
6.Plug and play, the computer does not need to install drivers
Pairing method:
One to one pairing method (one transmitter and one receiver):
1.First press and hold the Pair key of the transmitter, then turn on the power, wait for the green light to flash, then release the key, then press and hold the Pair key of the receiver, then turn on the power,wait for the green light to flash, and then release the key.
2.Connect the transmitter and receiver with the HDMI female cable.Wait until the green light of the receiver is always on. At this time, the transmitter is still flashing, indicating that the pairing has been completed. If the receiver is still in the flashing state, it means that the pairing is unsuccessful. Please power off the transmitter and the receiver then pairing again.
3.After pairing, power off the transmitter and receiver, unplug the HDMI Female cable and wait for a few seconds before powering on again. The green lights of the transmitter and receiver are flashing, indicating that pairing has been successful.
One to many pairing method
(one 1. According to the above one-to-one pairing method, a transmitter with the first receiver, then pair this transmitter with the second receiver. In the same way, pair this transmitter with the third receiver and the fourth receiver one-to-one, When all receivers are paired with the same transmitter one-to-one successfully, they can be powered on for use. (Note: One to many supports one transmitter to four receivers at most)
Multi to one transmitter pairing method (multi transmitter and one receiver):
1.First press and hold the Pair key of the receiver, then turn on the power, wait for the green light to flash, then release the key, then press and hold the Pair key of the transmitter, then turn on the power,wait for the green light to flash, and then release the key.
2.Connect the receiver and transmitter with the HDMI double female cable. Wait until the green light of the transmitter is always on. At this time, the receiver is still flashing, indicating that the pairing has been completed. If the transmitter is still in the flashing state, it means that the pairing is unsuccessful. Please power off the transmitter and then pair again.
3.After pairing, power off the receiver and transmitter, unplug the HDMI female cable and wait for a few seconds before powering on again. The green lights of the receiver and transmitter are flashing,indicating that pairing has been successful.
4.According to the one-to-one pairing method, pair the first transmitter with a receiver. After the pairing is successful, pair the second transmitter with this receiver one-to-one. By analogy, pair the
third, fourth, fifth, and sixth transmitters with the same receiver one-to- one. When each transmitter and the same receiver are paired one-to-one successfully, the pairing is completed, and the power can be
turned on.(Note: many to one supports up to six transmitters to one receiver)
Packing list(TX RX Option)
Transmitter
Receiver
Antenna
Micro USB charging cable
HDMI male to female adapter
Model: GT-HWEX50M
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>