LAPP MS MSR M ATEX BRUSH Strain Relief Cable Instruction Manual
- June 15, 2024
- LAPP
Table of Contents
MS MSR M ATEX BRUSH Strain Relief Cable
Instruction Manual
Instruction sheet
IIC Gb II 1D Ex ta IIIC
Assembly:
- Screw SKINTOP® into housing or tighten with locknut (tightening torque M)
- Put cable through
- Tighten the capnut (tightening torque M)
Protection class:
IP68 – in acc. to EN 60 529
IP66 in acc. to EN 60 529
Temperature range:
Identification| Gr6Be Size| denying and sealing range| Seal color| Marking on
the sealing
---|---|---|---|---
DIN IEC 62444
Type of cable anchorage| lightening torque ( NM| OF (mm)
SKINTOP® MS-M20 ATEX BRUSH| M20x1,5| A| 12| 7 – 13| Black| violet stripe
SKINTOP® MS-M25 ATEX BRUSH| M25x1,5| A| 12| 9 – 17| Black| violet stripe
SKINTOP® MS-M32 ATEX BRUSH| M32x1,5| A| 17| 11 – 21| Black| violet stripe
SKINTOP® MS-M40 ATEX BRUSH| M40x1,5| A| 17| 19 – 28| Black| violet stripe
SKINTOP® MS-M50 ATEX BRUSH| M50x1,5| A| 20| 26- 35| Black| violet stripe
SKINTOP® MS-M63 ATEX BRUSH| M63x1,5| A| 20| 34 – 45| Black| violet stripe
SKINTOP® MS-M63 plus ATEX BRUSH| M63x1,5 plus| A| 30| 44 – 55| Black| violet
stripe
SKINTOP® MSR-M25 ATEX BRUSH| M25x1,5| A| 12| 6 – 13| Grey| violet stripe
SKINTOP® MSR-M32 ATEX BRUSH| M32x1,5| A| 17| 7 – 15| Grey| violet stripe
SKINTOP® MSR-M40 ATEX BRUSH| M40x1,5| A| 17| 16 – 23| Grey| violet stripe
SKINTOP® MSR-M50 ATEX BRUSH| M50x1,5| A| 20| 19 – 29| Grey| violet stripe
Note:
- The cable entries is to be used only for non-armoring cables and only for fix installation.
- The BRUSH is to be used only for EMC-purposes. It is strictly forbidden to use the BRUSH as a potential equalization.
- In areas with combustible dust the glands can be used only for threaded holes.
- If the content of this bag will be split on two or more units, a copy of this instruction sheet must be placed in every packing unit.
Installation
Prepare a cable for contacting of screen braiding in one of the following
forms.
A. Remove a cable sheath from the end section of screen braiding.
B. Remove a segment of cable sheath at the contact area.
C. Pull the fringe section of screen braiding over the cable sheath. 
Pull the cable through. The contact brush must be on screen
braiding.
| Size | [mm] |
|---|---|
| M20x1,5 | 17 |
| M25x1,5 | 19 |
| M32x1,5 | 22 |
| M40x1,5 | 26 |
| M50x1,5 | 30 |
| M63x1,5 | 38 |
| M63x1,5 plus | 40 |
Tighten the cap nut with recommended tightening torque M.
C€ 0637
EU DECLARATION OF CONFORMITY
| Document no.’ | CE21 10023EN- 00/06/20 |
|---|---|
| Manufacturer’ | U.L Lapp GmbH Schulze Delitzsch-Str. 25 70565 Stuttgart Germany |
This declaration is issued under the sole responsibility of the manufacturer.
| Product/ object description | SKINTOP MS-M ATEX BRUSH/MSR-M ATEX BRUSH |
|---|---|
| Product/ object name: | SINTOP MS-M ATEX BRUSH/MSR-M ATEX BRUSH |
The object of the declaration described above is in conformity with the
relevant Union harmonization legislation: 20 14/34/EU
Approval-No.: IBE KUO1ATEX1041 X IC Ex IBE 13.0026¥
References to other technical specifications :
- IEC 60079-0:2018
- IEC 60079-7:2015/41:2018
- 60079-312014
- 60079-0:2017
- 6C 60079-7:2015/A12017
- EC 60079-31:2013
| Signed for and on behalf of: | U.A. Lapp GmbH |
|---|---|
| Place of issue: | Stttgart / Germany |
| Date of issue: | 04,/06/2020 |
| Signatory’s name: | iA. Daniel Miller |
| Signatory’s title: | Deputy ATEX responsible |
Signature
U.I.LAPP GmbH
Schulze-Delitzsch-Straße 25
D-70565 Stuttgart
Tel.0711/7838-1010
Internet:www.lappkabel.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>