YARDISTRY YM117556X 10 Inch Meridian Wood Counter Instruction Manual

**YARDISTRY YM117556X 10 Inch Meridian Wood Counter Instruction Manual

**

Important Safety Notice!

Yardistry components are intended for privacy, decorative and ornamental use only.

Product is NOT INTENDED for the following:

• A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds.
• As load bearing support for a building, structure, heavy objects or swings.
• Used in structures that trap wind, rain or snow that would create extra load on the product.

Permanent structures may require a building permit. As the purchaser and or installer of this product you are advised to consult local planning, zoning and building inspection departments for guidance on applicable building codes and/or zoning requirements.

Wood is NOT flame retardant and will burn. Grills, fire pits and chimineas are a fire hazard if placed too close to a Yardistry structure. Consult user’s manual of the grill, fire pit or chiminea for safe distances from combustible materials.

Wear gloves to avoid injury from possible sharp edges of individual elements before assembly.

During installation, follow all safety warnings provided with your tools and use OHSA approved safety glasses. Some structures may require two or more people to install safely.

Check for underground utilities before digging or driving stakes into the ground!

It is important during assembly to closely follow the instructions, complete the assembly on a solid level surface and that you follow the instruction to square up, level and anchor the structure, this will reduce the gap at wood connections during assembly.

Instructions for Proper Maintenance

Your Yardistry structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you, the owner, properly maintain it.

HARDWARE:

• Check metal parts for rust. If found, sand and repaint using a non-lead paint complying with 16 CFR 1303.
• Inspect and tighten all hardware after completion of assembly; after first month of use; and then annually. Do not over-tighten as to cause crushing and splintering of wood.
• Check for sharp edges or protruding screw threads, add washers if required.

WOOD PARTS:

• Applying a water repellent or stain (water-based) on a yearly basis is important maintenance to maintain maximum life and performance of the product.
• Check all wood members for deterioration, structural damage and splintering. Sand down splinters and replace deteriorated wood members. As with all wood, some checking and small cracks in grain is normal
• Some gapping may occur at some wood connections.

Tools Required:

• Standard or Cordless Drill
• Safety Glasses
• Tape Measure
• Square

If you dispose of your Yardistry structure: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards at the time it is discarded. Be sure to follow your local waste ordinances.

General Information

Wood components are manufactured with Cedar (C. Lanceolata) which is protected with factory applied water-based stain. Knots, small checks (cracks) and weathering are naturally occurring and do not affect the strength of the product. Annual application of a water-based water repellent sealant or stain is important and will help reduce weathering and checks.

www.yardistrystructures.com

Questions?
Call toll free or write us at:
1 888-509-4382
support@yardistrystructures.com

Patents Pending

Part Identification

Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions maybe smaller or larger.

4pc. (1451) – FR/BK Bar- 1255.7mm (49-7/16″)

4pc. (1450) – Bar Top A- 1330.4mm (52-3/8″)

4pc. (1449) – Bar Top B- 1139.mm (44-7/8″)

4pc. (738) – Plinth- 177mm.8mm (7″)
(Y50131-738)

2pc. (1227) – Centre Block- 139.7mm (5-1/2″)
(Y50131-1227)

2pc. (1447) – Bar End- 425.5mm (16-3/4″)
(Y50131-1447)

2pc. (1448) – Bar Joist- 425.5mm (16-3/4″)

2pc. (1446) – Bar Center Joist- 425.5mm (16-3/4″)
(Y50131-1446)

1pc. (1231) – Post- 939.8mm (37″)

4pc. (1445) – Bar Gusset 425.5mm (16-3/4″)

4pc. Lag Screw (1/4″ Shank) 5/16 x 3″ (Y06218-330)

10pc. Pan Screw (Y06491-722)

16pc. Wood Screw (Y06091-740)

32pc. Wood Screw (Y06091-522)

80pc. Wood Screw (Y06091-513)

4pc. -1/4 – 5/16 Large Washer (Y05118-311)

1pc. #2 x 2″ (Y00400-005) Robertson Driver

1pc. Y00419-160 Corner Bracket

Step 1: Inventory Parts

1. This is the time for you to inventory all your hardware and components referencing the parts identification sheets. This will assist you with your assembly.
   • Each step indicates what you will need for assembly.
2. If there are any missing or damaged pieces or you need assistance with assembly please contact the consumer relations department directly. Call us before going back to the store.
3. Read the assembly manual completely, following the instructions in order.

1-888-509-4382
support@yardistrystructures.com

YM11814
CARTON I.D STAMP:/NO.

STEP 2: Post Assembly

1. Flush to the bottom of (1231) Post place one (738) Plinth on each side so the ends are tight together and fit snug. Make sure the rounded edges are on top. Attach each (738) Plinth to (1231) Post with four (S15) Wood Screws per plinth. Place Post Assembly centred between two Gazebo Posts. (F2.1 and F2.2)
2. On the (738) Plinth facing the inside of the structure place one Corner Bracket centred and flush to the bottom then attach with two (S23) Pan Screws. (F2.1 and F2.2)
   F2.1: Inside View
   
   F2.2
   

Wood
1 x (1231) Post
4 x (738) Plinth

Hardware
16 x #8 x 1-3/4″
2 x #10 x 2-1/2″
1 x Corner Bracket

Step 3: Attach Bar Gussets

1. Measure 2-1/4″ down from the top of (1231) Post then place one (1445) Bar Gusset on each side facing the Gazebo Posts. Each side of the (1445) Bar Gusset should extend the post by 5-5/8″. (F3.1 and F3.2)

2. Make sure gussets are square then attach each (1445) Bar Gusset to (1231) Post with one (LS6) Lag Screw (with 1/4-5/16″ Large Washer) and two (S23) Pan Screws per gusset. (F3.1 and F3.2)
   F3.1
   
   F3.2
   
   Wood
   2 x (1445) Bar Gusset
   Hardware
   2 x 5/16 x 3″ (1/4-5/16″ large washer
   4 x #10 x 2-1/2″

3. Measure 34-3/4″ up from the bottom of each Gazebo Post then place one (1445) Bar Gusset on each post facing inside. Each side of the gusset should extend the post by 5-5/8″. (F3.3, F3.4 and F3.5)

4. Make sure gussets are square then attach each (1445) Bar Gusset to each Gazebo Post with one (LS6) Lag Screw (with 1/4-5/16″ Large Washer) and two (S23) Pan Screws per gusset. (F3.5)
   F3.3
   
   F3.4
   
   F3.5
   
   Wood
   2 x (1445) Bar Gusset
   Hardware
   2 x 5/16 x 3″ (1/4-5/16″ large washer)
   4 x #10 x 2-1/2″

Step:4 Frame Assembly

1. Lay out two (1451) FR/BK Bars so the pilot hole orientations match. In between the (1451) FR/ BK Bars place one (1447) Bar End at the end with one set of pilot holes, flush to the ends and bottoms, then attach with two (S3) Wood Screws per side. (F4.1)
2. Measure 3/4″ from the top of each (1451) FR/BK Bar then place one (1448) Bar Joist at the centre pilot holes and attach with two (S3) Wood Screws per side. (F4.1)
3. Measure 2-3/4″ in from the ends of (1451) FR/BK Bar and 3/4″ down from the tops then attach one (1446) Bar Centre Joist with two (S3) Wood Screws per side. (F4.1)
4. Repeat A – C again to create a second Frame Assembly.
   F4.1
   
   Wood
   4 x (1451) FR/BK Bar
   2 x (1447) Bar End
   2 x (1448) Bar Joist
   2 x (1446) Bar Centre Joist
   Hardware
   24 x a #8 x 2-1/2″

Step: 5 Attach Centre Blocks

1. On one Frame Assembly place two (1227) Centre Blocks tight to the outside face of (1446) Bar Centre Joist and to each (1451) FR/BK Bar then attach to (1446) Bar Centre Joist with one (S24) Wood Screw per block. (F5.1)
   F5.1
   
   Wood
   2 x (1227) Centre Block
   Hardware
   2 x #10 x 4″

Step: 6 Attach Frame Assembly

1. Centre Frame Assembly with Centre Blocks on top of two (1445) Bar Gussets. Attach (1445) Bar Gussets to (1447) Bar End and (1446) Bar Centre Joist with two (S15) Wood Screws per gusset. (F6.1 and F6.2)

2. Centre Frame Assembly without Centre Blocks on remaining (1445) Bar Gussets so (1451) FR/BK Bars are tight together and (1227) Centre Blocks are tight to (1446) Bar Centre Joist then attach (1445) Bar Gusset to (1447) Bar End and (1446) Bar Centre Joist with two (S15) Wood Screws per gusset. (F6.2 and F6.3)
   F6.1
   
   F6.2
   
   F6.3
   
   Front and back of the Frame Assembly will overhang the gussets by 1″.
   Hardware
   8 x #8 x 1-3/4″

3. Attach each (1446) Bar Centre Joist to (1231) Post and (1447) Bar Ends to Gazebo Posts with three (S24) Wood Screws per board (F6.4 and F6.5)
   F6.4
   
   F6.5
   
   Hardware
   12 x #10 x 4″

4. Attach (1446) Bar Centre Joist to both (1227) Centre Blocks with one (S24) Wood Screw per block. (F6.7)

5. Attach each (1451) FR/BK Bar to (1227) Centre Blocks with two (S3) Wood Screws per (1451) FR/ BK Bar. (F6.6 and F6.7)
   F6.6
   
   F6.7
   
   Hardware
   8 x #8 x 2-1/2″
   2 x #10 x 4″

Step 7: Bar Top Assembly

1. On one side of the Frame Assembly place one (1450) Bar Top A and one (1449) Bar Top B tight to (1451) FR/BK Bars and to each other. End of Bar Tops should be evenly spaced to (1447) Bar Ends. Repeat on other side of the Frame Assembly so each Bar Top is in the opposite position on each side. (F7.1)
   F7.1
   
   Wood
   2 x (1450) Bar Top A
   2 x (1449) Bar Top B

2. Attach each (1450) Bar Top A and each (1449) Bar Top B to (1447) Bar Ends, (1448) Bar Joists and (1446) Bar Centre Joists with eight (S15) Wood Screws per (1450) Bar Top A and six (S15) Wood Screws per (1449) Bar Top B. (F7.1, 7.2 and F7.3)
   F7.1
   
   F7.2
   
   F7.3
   
   Hardware
   28 x #8 x 1-3/4″

3. Tight to each (1450) Bar Top A and (1449) Bar Top B place two more sets of Bar Tops so they are staggered. (F7.4)

4. Make sure all boards are evenly spaced then attach remaining Bar Tops to (1447) Bar Ends, (1448) Bar Joists and (1446) Bar Centre Joists with eight (S15) Wood Screws per (1450) Bar Top A and six (S15) Wood Screws per (1449) Bar Top B. (F7.4)
   F7.4
   
   Wood
   2 x (1450) Bar Top A
   2 x (1449) Bar Top B
   Hardware
   28 x #8 x 1-3/4″

Step 8: Fasten Corner Bracket

1. Fasten Corner Bracket to ground surface using appropriate hardware for surface material. (F8.1 and F8.2)
   Note: Anchoring hardware is not included.
   F8.1
   
   F8.2
   

Limited Warranty

Yardistry warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. In addition, for any product with lumber, all lumber is warranted for five (5) years against rot and decay. This warranty applies to the original owner and registrant and is non-transferable.

Regular maintenance is required to assure the integrity of your product and is a requirement of the warranty. This warranty does not cover any inspection costs.

This Limited Warranty does not cover:

• Labour for replacement of any defective item(s);
• Incidental or consequential damages;
• Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper use or installation; acts of nature, including but not limited to wind, storms, hail, floods, excessive water exposure;
• Minor twisting, warping, checking or any other natural occurring properties of wood that do not affect performance or integrity.

Yardistry products have been designed for safety and quality. Any modifications made to the original product could damage the structural integrity of the product leading to failure and possible injury. Yardistry cannot assume any responsibility for modified products. Furthermore, modification voids any and all warranties.

This product is warranted for RESIDENTIAL USE ONLY. Yardistry disclaims all other representations and warranties of any kind, express or implied.

This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or province to province. This warranty excludes all consequential damages, however, some states/provinces do not allow the limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.

Customer Registration Card

First Name:
Initial:
Last Name: ___

Street:
PO Box:
Apt.: ___

City:
State/Province:

ZIP/Postal Code:
Country:

E-mail Address:
Telephone Number:

Model Name:
Model Number (from front cover):

Date of Purchase (mm/dd/yyyy):
Place of Purchase:

Comments: ___

Mail To
Yardistry
375 Sligo Road West, PO Box 10
Mount Forest, Ontario, Canada, NOG 2L0
Attention: Consumer Relations

Online Registration
www.yardistrystructures.com/warranty

Yardistry would like to say “Thank you” for your time and feedback.

Yardistry — North America
Toll Free Customer Support: 1.888.509.4382
info@yardistrystructures.com
www.yardistrystructures.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>