FISHER PAYKEL EB24 Coffee Maker Steam Oven Speed Oven User Guide

**FISHER PAYKEL EB24 Coffee Maker Steam Oven Speed Oven User Guide

**

WARNING!

Cut Hazard
Take care – some edges are sharp.
Failure to use caution could result in injury or cuts

Checking for transport damage
After removing the packaging, make sure the product is complete and undamaged and that all accessories are present. Do not use the appliance if it is visibly damaged. Contact Customer Care

IMPORTANT!

• Before connecting the appliance to the electrical supply make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. If in doubt, consult a qualified technician.
• The appliance must be properly installed before operation to ensure that no electrical  components are accessible. Ensure that power is not supplied to the appliance whileinstallation work, repairs or maintenance is performed.
• Be certain your appliance is properly installed and grounded by a qualified technician. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and effective grounding system. It is imperative that this basic safety requirement be met. If there is any doubt, have the electrical system of the house checked by a qualified electrician. The manufacturer cannot be held responsible for damages caused by the lack, or inadequacy, of an effective grounding system.
• Do not use an extension cord to connect the appliance to electricity. Extension cord doesn’t  guarantee the required safety of the appliance (danger of overheating).
• Before service or maintenance disconnect the power supply by either switching off the main switch and unplugging the unit.
• Install or locate this appliance only in accordance with the provided installation instructions.
• Installation work and repairs must be only performed by a trained technician in accordance with national and local safety regulations. Repairs and other work by unauthorized persons could be dangerous and may void the warranty.
• Only use original spare parts. Only then can the manufacturer guarantee the safety of this machine.
• Never open the outer casing of the appliance. Tampering with electrical connections or components and mechanical parts is dangerous and may cause machine damage.
• If the machine is installed in combination with other appliances, a protective base should be installed between the appliance and the unit.
• Do not install or use outdoors even if installed in the display cabinet.
• To protect against fire, electric shock and injury to persons do not submerge the cord or plugs in water or other liquids.
• To reduce the risk of injury, do not drape cord over the counter top or table top where it  can be pulled on by children or tripped over unintentionally.
• Do not let the cord hang over the edge of a table or counter, or touch hot surfaces.
• Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner.
• Return appliance to an authorized service facility for examination, repair or adjustment.
• To disconnect turn the machine off, switch off the main switch then remove the plug from the wall outlet.
• Do not allow children and animals to stop or linger near the appliance when it is pulled out of the cabinet.
• Do not leave the machine pulled out of the cabinet when it is being used.
• Do not leave the machine pulled out of the cabinet when it is not needed.
• Install the machine according to the instructions in the handbook to guarantee there are no spills when it is pulled out from the cabinet.
• he rails fixing panel must have a thickness suited to the fixing screws supplied standard.
• The panel material must be suited to the machine weight of approximately 55lb.

PARTS SUPPLIED

• Screws (28)

• Rails (2)

• Clip (1)

• Spacers
  (4) for side
  (4) for bottom

PRIOR TO INSTALLATION

• The countertop and coffee maker cavity are square and level, and are the required dimensions.
• The installation will comply with all clearance requirements and applicable standards and regulations.
• The isolating switch will be easily accessible to the customer with the coffee maker installed.
• The electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 59 1/16″ (1.5m) in front of the bottom edge of the opening.
• The cable may enter the cavity from the side, top or bottom, but top entry must be at the rear of the cavity.
• The coffee maker connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
• The coffee maker will rest on a surface that can support its weight.
• The height from the floor suits the customer.
• You consult local building authorities and by-laws if in doubt regarding installation.

IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the coffee maker during use.
To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, commend moisture-proofing the cavity

Optional Trim kit installation
If you are using a 30″ (762mm) trim kit, refer to the separate Trim Kit Installation Guide.

AFTER INSTALLATION

IMPORTANT!
Take extra care not to damage the lower trim of the coffee maker during installation. The trim is important for correct air circulation and allows the door to open and close without obstruction. The manufacturer does not accept any responsibility for damage resulting from incorrect installation.

• The coffee maker can be used fully without obstruction.
• The power supply cable does not touch any hot metal parts.
• The isolating switch is easily accessible to the customer with the coffee maker installed.
• You complete the ‘Final checklist’ at the end of the installation.
• If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorized Service Center, Customer Care, or contact us through our local website listed at the end of this document.

PRODUCT DIMENSIONS

• TOP

• SIDE

• FRONT

PRODUCT DIMENSIONS

CABINETRY DIMENSIONS (18 1/8″ (460mm) HIGH CAVITY)

Verify the minimum measurements required for correct installation of the appliance. The coffee maker must be installed in a column and the column must be firmly fixed to the wall with commercially available brackets.

IMPORTANT!

• All installation or maintenance operations must be performed with the appliance disconnected from the mains electricity supply.
• Kitchen furniture in direct contact with the appliance must be heat resistant 149°F min (65°C min).
• To guarantee correct ventilation, leave a gap at the bottom of the cabinet (see measurements below

1. SIDE

2. TOP

CABINETRY DIMENSIONS

CABINETRY DIMENSIONS (18 7/8″ (480mm) CAVITY TRIM KIT)

Verify the minimum measurements required for correct installation of the appliance. The coffee maker must be installed in a column and the column must be firmly fixed to the wall with commercially available brackets.

Lower Trim Kit
The Lower Trim kit shown is available to order separately from fisherpaykel.com. To install the trim kit, refer to the instructions which accompany it.

IMPORTANT!

• All installation or maintenance operations must be performed with the appliance disconnected from the mains electricity supply.
• Kitchen furniture in direct contact with the appliance must be heat resistant 149°F min (65°C min).
• To guarantee correct ventilation, leave a gap at the bottom of the cabinet (see measurements below).

1. SIDE

2. TOP

CABINETRY DIMENSIONS

INSTALLATION INSTRUCTIONS

1. Position the rails on the sides of the cabinet. Fix with the screws provided, then extract them completely.

   • If the coffee maker is installed over a warmer drawer, use the top surface of this as a reference to position the rails.
   • In this case, there will be no surface to rest the rails on

2. Fix the power cable with the clip. The power cable must be long enough to allow the appliance to be extracted from thebaine to fill the coffee bean container.

   • The appliance must be earthed in compliance with legislation.
   • Electrical connections must be performed by a qualified electrician following the instructions

3. Position the appliance on the rails, making sure the pins are correctly inserted in the housings, then fix it with the screws supplied. If the height of the appliance requires adjusting, use the spacer disks provided.

4. If necessary, correct alignment of the appliance by positioning the spacers supplied under or at the sides of the support.

FINAL CHECKLIST

TO BE COMPLETED BY THE INSTALLER

• Make sure the coffee maker is level and securely fitted to the cabinetry.
• Check the lower trim is undamaged.
• Check there is adequate clearance. This is to ensure correct air circulation.
• Make sure any cable ties and internal packaging has been removed from the coffee maker cavity.
• Make sure all coffee maker vents and openings are clear and free of any obstruction or damage.

IMPORTANT!
Failure to make sure all vents are clear may result in poor product performance.

• Make sure the isolating switch is accessible by the customer

TEST OPERATION :

• Turn the power to the coffee maker on. The display should light up.
• Have you demonstrated the basic operation to the customer?
• Fill the water tank to the indicated level.

References

• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>