TOPENS TC175P Touch Panel Wired Keypad User Manual
- June 4, 2024
- Topens
Table of Contents
TOPENS TC175P Touch Panel Wired Keypad User Manual
Specifications
- Operating voltage: 12-24VDC ±10%
- Operating current: < 100mA
- User Capacity: 1000 users
- Card type (alternative): EM(ID) card
- Card reading distance: 1－15CM
- Working temperature: -20℃-+50℃
- Relay output: SPDT, 3A 120VAC/24VDC
Factory default settings
- Programming Password: 123456
- Common Access Password: None
- Backlight: Auto (for options)
- Relay Unlock output: 5 Seconds
- W26 port: Input (for options)
- Security mode: OFF
- Open mode: Card or Access Password, Access Password include Private Access Password (PIN) and Common Access Password
Light and Sound indicates
| Light: red and green Light Description | Access control status |
|---|---|
| Red light flash every 1 sec （Slow flash） | Standby state |
| Red light is always ON | Programming state |
| Green light is always ON within Open time | **** Unlocking state |
| Green light flash every 0.5sec (Fast flash) | Pending further action |
| Buzzer: Description | Indicates |
| --- | --- |
| 1 short buzz | Valid input |
| 3 short buzz | Invalid input |
| 1 long buzz | Programming success |
| Continuous long buzz | Restoring factory programming passwords |
Definition of the output wires
| JP1 terminal: NO | Mark | Color | Function |
|---|---|---|---|
| 1* | +12V | X | This wire has been cut off |
| 2 | GND | Black | Power-(12-24VDC negative) |
| 3 | PUSH | BLUE | Low level output |
| 4 | OPEN | Yellow | Door Release |
| 5 | BELL | Grey | BELL |
| 6 | BELL | White | BELL |
| JP2 terminal: NO | Mark | Color | Function |
| --- | --- | --- | --- |
| 1* | +12V | X | This wire has been cut off |
| 2 | GND | Black | Power-(12-24VDC negative) |
| 3 | DATA0 | Green | WG DATA0 |
| 4 | DATA1 | White | WG DATA1 |
| 5 | NC | Brown | Relay NC output |
| 6 | COM | Blue | Relay Com output |
| 7 | NO | Purple | Relay NO output |
NOTE: The red wire of the both 2 terminals has been cut off and it has
been soldered to the PCB of the keypad. Thus you can connect the 12-24VDC
power supply to the RED wire on the PCB and the BLACK wire of JP2 to power up
the keypad. 
Wire connection of the keypad to the gate &
door opener NOTE: Below wiring diagram is a universal wiring diagram of
the connection between the keypad and the opener. You can refer to the user
manual of the TOPENS gate opener for detailed wiring diagram. 
Connect the keypad to the
Gate/Door opener without power on the board, when using external power supply
for TC175P. In this situation, you need an external 12-24VDC power source to
make the keypad to work with the gate & door opener. 
Programming
- There are three kinds of passwords while programming: programming password, access password, card password.
- User ID is auto-generating 4-digit number started at 0001. The number increases with adding user one by one and ignores deleting user. Common Access Password has no ID.
- All passwords can be 3-6 digits in length.
- Programming password is used for programming.
- Access password is used to activate the gate when the keypad has been set to “password” or “password or card” mode.
- Card password is needed to enter after swipe the card when the keypad has been set to “password + card” mode.
- Factory default program password is 123456.
FAQ
How to Change the Programming Password
Old Programming Password # 0 New Programming Password # New Programming Password
How to Set Common Access Password
Programming Password # 21 new Common Access Password
How to Add Private Access Password (PIN)
Programming Password # 22 (3-6 digits access password)
How to Add User Card
Programming Password # 1 read card
How to Delete All Users
Programming Password # 40 0000
How to Delete User by Read Card
Programming Password # 41 read card
How to Add Card by Input Card Number
Programming Password # 23 input card number
How to Add Multi-card by Input Card NO. Zone
Programming Password # 24 input start card No. card Qty
How to Add “card +PIN” User
Programming Password # 3 read card PIN
0 How to Delete User by Input User ID NO.
Programming Password # 42 input User ID No.
How to Delete User by Input Card NO
Programming Password # 43 input card No.
How to Delete User by Input Private Access Password (PIN)
Programming Password # 44 (3-6 digits access password) #
How to Delete All Private Access Password (PIN) Users
Programming Password # 45 1111
How to Change “Relay Unlock Output”
Programming Password # 5 XX #
How to Set Open Mode
Programming Password # 6 XX
Reader Setting (For options)
6 Reader Setting (For options) Programming Password # 6 04
Security Function Setting, Anti-dismantle Alarm Setting (For options)
Programming Password # 7 XX
. Backlight setting(For options)
Programming Password # 8 XX #
How to Reset Factory Default Setting
Programming Password # 8 99 #
Reset to Factory Programming Password（123456）
Step1: Power off the keypad and connect pin 2&3 of RST together. ep2: Power on the keypad and buzzer will give 3 long buzz with green light flashes fast. Step3: Power off the keypad and disconnect pin2&3 and connect pin 1&2 of RST together. Step4: Turn on power again.
Reset to Factory Programming Password（123456）
Step1: Power off the keypad and connect pin 2&3 of RST together.
Step2: Power on the keypad and buzzer will give 3 long buzz with green
light flashes fast. Step3: Power off the keypad and disconnect pin2&3 and
connect pin 1&2 of RST together. Step4: Turn on power again. 
Support
TOPENS Website
http://www.topens.com/ Any question, please do not hesitate to contact us:
E-mail: support@topens.com Kindly include
your Product Model, Purchasing Date & Site, Order #, and your contact
information. All your concerns will be replied within 24 hours. Tel: +1
(888) 750 9899 (Toll Free USA & Canada)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>