BACKRACK 30107TB31 Back Rack Kit Instruction Manual

: June 15, 2024
: BACKRACK

Table of Contents

IMPORTANT INFORMATION
PARTS LIST FOR KIT
INSTALLATION INSTRUCTIONS
CUSTOMERS SUPPORT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BACKRACK 30107TB31 Back Rack Kit

IMPORTANT INFORMATION

The BACKRACK is secured to your truck with a pair of“ Stake Pocket Bolts” specifically designed for your make and model of truck. These bolts mount into each of the two front stake pockets. The BACKRACK assembly sits on the bed rails of your truck and is secured to these Stake Pocket Bolts. If your truck has a BEDLINER we suggest you remove it to install the Stake Pocket Bolts

PARTS LIST FOR KIT

PARTS LIST FOR KIT #30107

PART	DESCRIPTION	QTY
RP507S	Rail Plate	2
RMB507D	Rail Mount Bracket Driver	1
RMB507P	Rail Mount Bracket Passenger	1

HARDWARE BAG507A
FYZ001| 3/8-16 Hex Nut| 4
FYZ002| 3/8 Lock washer| 4
B32714| Sealed Bag Fasteners| 1
FYZ016| 5/8-11 Hex Nut Gr 2| 2
FYZ017| 5/8 Lock washer| 2
FYZ018| 5/8 Sae Flat Washer| 2
SF017| Foam Pad| 2
HARDWARE BAG507B
SBY507S| Stake Pocket Bolt| 2

PARTS LIST FOR KIT #30107TB, 30107TB31

PART	DESCRIPTION	QTY
TB503D	Toolbox Bracket Driver	1
TB503P	Toolbox Bracket Passenger	1

FOR MORE INFORMATION SCAN HERE!

INSTALLATION INSTRUCTIONS

Install the Stake Pocket Bolts into the two front stake pockets
Using a square and a pencil, draw a center line below the bed rail on the inside wall of the truck bed as a guide to drill two 7/16” diameter holes ( see drawing on back of sheet). Be sure that the flat steel portion of the Stake Pocket Bolt is below the oval hole (see drawing)
Mark hole locations and drill two 7/16” diameter holes to accommodate the Stake Pocket Bolt.
Secure the Stake Pocket Bolts into the stake pocket with the 3/8” lock washers and nuts.
Place Rail plates on bed rail, over stake pocket bolts.
Apply the black adhesive foam to one side of the Rail Plates. Cut foam into smaller pieces.
Place Rail Plate onto bed rail. The thread of the Stake Pocket Bolt will protrude through hole.
Attach the Rail mount Brackets to the Backrack Frame
Drop the tailgate and lay the Backrack on the tailgate (decals up) with long tube nearest you.
Slide Rail mount Bracket on to end of tube so the oblong slot aligns with hole in end of tube.
Secure to Backrack with W’ bolt assembly (1/2’ × 3-1/2” Bolt, lock washer, flat washer, nut).
Do not tighten at this time. Keep loose for adjustment later in installation.
There is a LH & RH Rail mount Bracket. Refer to photos for proper fit.
Place Backrack assembly with Rail mount Brackets attached on to bed rail
Place the Backrack assembly on the bed rails. It will be sitting on the Rail Plates.
The threaded portion of the Stake Pocket Bolt will be protruding through the holes.
Secure the assembly to the truck using the 5/8” flat washer, lock washer and nut.
DO NOT OVER TIGHTEN! Sheet metal is thin and will crush if over tightened.
Tighten until the lock washer begins to compress. Use your discretion.
Center Backrack behind cab and tighten all fasteners
Stand at the rear of the truck and visually center the Backrack behind the cab.
Finish the installation by tightening all nuts and bolts.
DO NOT OVERTIGHTEN THE STAKE POCKET BOLTS.
The W’ bolt assembly should be tightened as firmly as possible with an extension handle.

CUSTOMERS SUPPORT

READ THIS NOW!
Your truck should look like the one shown. If you
think you are missing any parts, think that this part
number is not for your truck or have any installation
question, call our customer service department at
toll free:

800-265-8137 or locally 905 849-3633
Other ways to reach BACKRACK:
Fax 905-849-4116
email: techsupport@backrack.ca

Logo