ACLAST AC-001 Ergonomic Computer Desk Chair Instruction Manual

ACLAST AC-001 Ergonomic Computer Desk Chair

Safety Precaution

The precautions written here are to prevent harm or damage to you or others.All of these are important contents for safe use, so be sure to observe them.

Attention

Ignoring this instruction and using the product incorrectly may result in injury or property damage.

WARNING

Cause of Suffocation
Do not cover your head with the plastic bag used for packaging.
Cause of Explosion
Do not disassemble or lubricate the gas cylinder.
Do not put the as cylinder into fire.
Do not 1nc1nerae.
Cause of Fall
Do not stand on the chair, use it as a stepping stone, or place it in an unstable position.
Do not sit on the armrests or lean on the backrest, or sit on only part of the seat.
Do not use the chair on slippery floors.
Cause of Poisoning
incineration may produce toxic gases.

Attention

Please ensure that the chair is assembled on a stable and flat surface to avoid injury or damage.
Be careful not to get your hands or fingers caught in the casters or reclining parts, as it may cause injury.
When turning the chair, pay attention to your surroundings to avoid colliding with any objects or people.
Do not use the chair for anything other than its intended purpose to avoid any accidents.
To prevent discoloration and deformation, please note that this product is designed for indoor use only.
Outdoor use or exposure to moisture may cause malfunction, rust, or discoloration.
Avoid using the chair in places exposed to direct sunlight or heat, such as near a stove, or in areas with significant humidity or dryness.
Please be sure to avoid any actions that could be considered dangerous, in addition to the above guidelines.

Upholstery Care:

To keep your upholstery looking its best, gently scrub the surface with a soft brush, or use a vacuum cleaner to remove dust from seams and crevices.

If you notice any stains or dirt, simply dab it with a soft cloth that has been dampened with a small amount of diluted neutral detergent. After cleaning, wipe off any remaining cleaner with a towel dampened with a little water.

Care of Metal and Resin Parts:

To clean metal and resin parts, wipe them down with a soft, dry cloth.
If they become dirty, wipe them with a diluted neutral detergent, then use a wrung cloth to remove the excess cleaner. Finally, wipe the parts with a dry cloth to completely remove any remaining detergent and water.

After sale policy

VIP Customer service 12] : Aclastus@126.com

1. Manufacturer’s Warranty for 365 Days Within 365 days from the date of purchase, if there is a failure or b real<down while using the product according to the instruction manual, we will replace the parts for free or replace the product at our discretion.
   The foUowing cases are not covered by the warranty, even within the warranty period:
   a. Damage caused by transportation, movement, dropping, or any other reasons after delivery.
   b. Malfunctions caused by failure to observe the precautions or specified conditions stated in the instruction manual labels, packaging, etc., or malfunctions caused by incorrect use exceeding the limits.
   c. Product damage repaired by anyone other than our company or the designated supplier.
   d. Damage caused by natural disasters such as earthqual<es, fires, Lightning stril<es, wind disasters, floods, salt damage, or other external factors.
   e. If the warranty card or order number is not presented, the warranty period cannot be confirmed.
   f. Leather (fabric) wear, synthetic leather hydrolysis or hardening, genuine leather discoloration or cracl<ing, sun fading, etc.
   g. Abrasions, scratches, stains, discoloration, etc. caused by daily use.
   h. Wear on casters, etc.
   i. Other defects caused by the negligence of the customer.

30-Day Return and Money-Back Guarantee (non-Amazon orders are subject to our store’s policies) If you are not satisfied with your purchase, you can return the product to Amazon’s designated location within 30 days from the date of your order, as long as you fo Uow Amazon’s return policy instructions. Refunds wi U be processed automatica Uy.
Please refer to the above Link for the return method and return conditions. The original manufacturer packaging is required for returns. Please do not discard the original boxes.
The above guarantees (1) and (2) are only applicable when the seUer is ACLAST Co., Ltd.
[Additional Information]

• The warranty information provided on this page ensures that we will repair the product free of charge within the warranty period and in accordance with the conditions specified in the instruction manual
• This warranty information does not limit your legal rights. Therefore, if you have any questions about repairs after the warranty period, please contact us by phone or email.
• Our 365-day quality assurance service provides support (guarantee) for 365 days from the date of your order. After ordering a new replacement product, the warranty period wiU not be extended.
• When lending or transferring our products to a third party, be sure to attach the order number and instruction manual together. We are not responsible for any trouble caused by the act of lending or transferring.
• After-sales service rights such as returns and replacements are applicable only to the customer who purchased the product. These rights are not transferred even if the product is lent or transferred to a third party.
• When replacing parts or products, we may use alternatives with a different appearance.
• If the warranty has expired, we will provide after-sales service, but the customer will bear the freight and other costs.
• This warranty information on this page is valid only in the United States.
• Except for special circumstances, the warranty provided on this page is valid only for personal use of the product.
• If you would like to replace the product under warranty, you must return the original product to us. After confirmation by our customer support, you need to return the product within a certain period of time. Please note that if you change the time of return without contacting us in advance, you may not be covered by the warranty.
• We do not provide repair services.
• We do not sell assembled products.
  [Regarding Your Personal Information]
  The Company, along with its affiliated companies (hereinafter referred to as “the Company”), will handle your personal information (such as your name and address provided by you) as follows:
  We will use your personal information to respond to your inquiries about our products, confirm repairs, develop new products, etc., and keep a record of the content of your consultation for these purposes.
  Your personal information will not be disclosed or provided to third parties outside of the company, except when the company entrusts a cooperative company to carry out maintenance, when it is necessary to perform business or exercise the authority stipulated by laws and regulations, or when there are other legitimate purposes.
  If you request disclosure of your personal information, we will disclose it to you without delay. If you wish to be notified of the purpose of use of your personal information, correct, add, delete, stop using, or stop providing it to third parties, please contact us at our email address.

Point of Assembly

Do not tighten the screws from the beginning

• Tighten all the screws only in halfway at the beginning of the assembly, otherwise the screws might not be aligned with the screw

1. Temporarily tighten all screws to 80°/o

Tighten all screws up to80%

|
2. Finally, tighten all the screws firmly.

Tighten all screws tight

|

How to tighten the diagonal screws

1. Install the first screw into any hole and then install the second screw diagonally.
2. Install the remaining screws.

See the following sequence for the screws on the opposite bracket

|

Please lay the carpet

To protect the floor, place a rug under the unit as shown in the illustration.

• Thick cloth
• Packing cardboard, etc.

Parts checking

1. Base (1 &2)

2. Caster

3. Cylinder

4. Tilt Mechanism

5. Armrest (L&R)

6. Cushion

• Allen Key

• five-Star base Screws

• Tilt Mechanism Screw

• Screws at the bottom

• Armrest screw

• Backrest

::Note : BCD screws are already pre-installed on the seat and backrest during the quality check. We have provided an extra screw for ABCD screws as a spare.

Assembly 1

1. Installation of five-star base and gas lift 1
   Please remove the protective cover of the five-star base first, and then insert the five-star base B according to the reference diagram, and then tighten the five-star base screw A.
   Repeat the above steps to install the other four legs.
   *Insert the casters 2
   Note: it will be easier to install the casters after fixing the five-star base and casters according to the recommended gesture.
   Insert the gas lift 3

**

Assembly 2

2. Installation of backrest armrests
   Please note that you should install the armrests before installing the seat cushion. Following the recommended procedure can help you quickly and easily install the chair.
   First, remove the pre-installed screws from the backrest. Then, referring to the picture, insert the backrest into the armrest and tighten the screws.
   Repeat the above steps to install the armrest on the other side.
   *Note: If the connection between the backrest and armrest is too tight during installation, the screw may not enter. Please keep a certain gap at the connection and prioritize screw installation. The gap will naturally align after installation.
   

Assembly 3

3. Installation of Backrest, Armrest, and Seat Cushion
   * Please note that you should install the armrest first before installing the seat cushion. Following the recommended installation method can help you quickly and easily install the chair.
   First, remove the pre-installed screws on the backrest. Lay the backrest flat and insert the seat cushion into the correct position.
   Tighten the armrest screws. Note** : Inserting the seat cushion in the manner shown in the picture is the easiest installation method tested by the ACLAST team.

First, remove the pre-installed screws on the seat cushion. Install the tray on the seat cushion as shown in the picture. Please install the screws in a criss-cross pattern according to the installation points.
*Note:* Pay attention to the orientation of the tray before installation. Incorrect installation can cause the chair to tip over.
After correct installation, the height adjustment lever should be on your right side during normal use.
Important Note:** The front and rear screws of the tray have different sizes. Please strictly follow the corresponding size to remove and install the screws. Install the removed pre-installed screws into the original pre- installed holes (front hole M6x40MM, rear hole M6x35MM), and do not mix them to avoid unstable screw fixation.

Assembly 3

4. Chair Assembly Completed

Please refer to the picture and combine the upper and lower parts of the chair together.
*Note:It is recommended to tilt the chair and insert the gas lift and five-star base into the tray first. Then lift the chair up. This will make the assembly process easier.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>