RIWORAL UX04 Channel Audio Mixer Sound Board System Owner’s Manual
- June 15, 2024
- RIWORAL
Table of Contents
RIWORAL UX04 Channel Audio Mixer Sound Board System
4-Channel Audio Mixer Sound Board System Features Digital USB/Bluetooth Input And Stereo Equalizer w/16 effects And Studio Monitor Function
System Description
Box Content
- 1 Audio Mixer
- 1 AC/DC Adapter
- 1 User’s Manual
System Overview
The UX04/06/08 is a 4/6/8 Channel Bluetooth studio mixer. No matter what your audio mixing needs, the UX04/06/08 mixing console provides the performance and features that can take your talent to the next level. The personal mix:
- 4 Channel Input:1st/2nd Mono Audio Input Channel Use XLR And 1/4 Inch compatible Jacks,3rd/4th Stereo Audio Input Channel Use 1/4 Inch Jacks
- 6 Channel Input:1st/2nd/3rd/4th Mono Audio Input Channel Use XLR And 1/4 Inch compatible Jacks,5th/6th Stereo Audio Input
- Channel Use 1/4 Inch Jacks
- 8 Channel Input:1st/2nd/7th/8th Mono Audio Input Channel Use XLR And 1/4 Inch compatible Jacks,3th/4th&5th/6th Stereo Audio Input Channel Use 1/4 Inch Jacks.
- Ultra-low noise discrete mic preamps with +48V phantom power
- 3-Band EQ on all channels with built-in 16 digital special effects
- USB/FLASH READER/MP3 compatibility. Bluetooth wireless streaming function, which enable users to stream music tunes from iPad, iPhone, and Android smart phone.
Specifications
- Mono Inputs
| Mic input | Electronically balanced, discrete input configuration |
|---|---|
| Bandwidth | 10Hz to 60kHz ±3dB |
| Distortion(THD&N) | 0.01% at 4 dBu, 1kHz, Bandwidth 80 kHz |
| TRIM range | +10dB to +60dB |
| Line Input | Electronically balanced |
| Bandwidth | 10Hz to 60kHz ±3dB |
| Distortion(THD & N) | 0.01% at 4dBu, 1kHz, Bandwidth 80kHz |
| Line level range | +10dBu to -40 dBu |
- Equalization
| Hi Shelving | 12kHz +/- 15dB |
|---|---|
| Mid Range | 2.5kHz +/- 15dB |
| Lo Shelving | 80Hz +/- 15dB |
- Master Mix Section
| Max Output | +22 dBu balanced |
|---|---|
| Aux Send Max Out | +22 dBu unbalanced |
| Control Room Out | +22 dBu unbalanced |
| Signal-To-Noise Ratio | 112 dB, all channel at Unity Gain |
- Power Supply
| Mains Voltages | USA/Canada, -120V AC, 60Hz |
|---|
U.K./Australia, -240V AC, 50Hz
Operation Instructions
Control Elements and Connector
INPUT CHANNEL SECTION
-
INPUT JACK (MIC/LINE)
MIC:XLR Audio Jack-Balanced LINE:1/4”（6.35mm) Audio Jacks-Unbalanced -
PHANTOM POWER SWITCH EACH CHANNEL
Press this button to enable phantom power for this channel. -
GAIN CONTROL
Adjust the input signal level.-
* **HI EQ**High range EQ control for up to 15dB of boost or cut at 12KHz and above. Use it to add sizzle to cymbals, add an overall sense of transparency or edge to keyboard, vocals, and guitar.
-
MID EQ
Mid range EQ control for up to 12 dB of boost or cut centered at 2.5KHz. Midrange EQ is often thought of as the most dynamics because the frequencies that define any particular sound are almost always found in this range. You can create useful EQ changes by using this knob to adjust sound. -
LOW EQ
Low range EQ control for up to 15dB b at 80Hz and below. This frequency represents the punch in bass drums and bass guitar.
-
-
AUX1/AUX2/FX CONTROL
Aux sends FX marked offering a direct route to the built-in effect processor and therefore post-fader and post-mute -
PAN CONTROL
PAN control determines the channel signal position in the stereo image. use PAN control to set the signal to just one output, which gives you extra flexibility recording the situation. For example, when routing to subgroups 3 and 4, the left-hand side will steer signal to output group 3 only, and the hard right-hand side will direct to output group 4 only.
-
CHANNEL FADER
Adjust the volume of the sound input from the microphone or other sources connected to each channel It works together with the maser fader. Normal operating position is at the “O” mark. providing 4dB gain above that point if required. MIXER OUTPUT SECTION
-
CD/TAPE INPUT JACKS (LEFT/RIGHT)
This RCA Jack pin uploads the stereo sound source. Use this jack when you want to connect the CD player directly to the mixer. -
CD/TAPE OUTPUT JACKS(LEFT/RIGHT)
This RCA Jack pin can be connected to an external recorder likean MD recorder to record the same signal is being released through jack. -
RETURN JACK
Connect all kinds of effects from outside. -
MAIN OUTPUT JACKS (LEFT/RIGHT)
Send the mixed output to main amplifier or next stage equipment through XLR jacks. -
AUX1 AUX2 JACK
Jack AUX usually acts as a feedback for the effect mix (made using aux post a fader sends)by connecting output from extreme effects. -
PHONE JACK
Connect headphone to this jack to monitor the output
Setup
-
MP3
-
FX TO AUX1
Control fx effect to jack of aux 1 device. -
FX TO AUX2
Control fx effect to jack of aux 2 device. -
AUX 1
Control aux 1 device of volume -
REPEAT
Control effect repeat times -
RETURNS
Adjust the level when the signals received on jack sent to the device -
CD/TAPE REP
Adjusts the signal level sent from jack CD input. -
PHONES Control
Use this control to adjust the output level of the control room and the volume of the head phone. -
POWER SWITCH ON/OFF
-
EX/EFFCT FADER
Control the level of the input effect signal. -
MAIN L/R FADER
Your FADER main mix uses high-precision fondest control the upgrading level of the main mix. -
AC IN JACK
