HOPEPOWER T02-C Smart Wireless Charging User Manual
- June 15, 2024
- HOPEPOWER
Table of Contents
HOPEPOWER T02-C Smart Wireless Charging
- This product is a desktop wireless charger, mainly for Apple, Android mobile phones or tablets and other 3C products provide charging function
- 2 in 1 Design. Compatible Type-C, USB wired output and wireless charging output|;
- The product built-in intelligent detection chip, detected a mobile phone or digital products and other load access When port, the product automatically starts the wired or wireless charging function for digital products;
- Adopt multiple protection circuits such as over current, over voltage, over temperature and short circuit, as well as high temperature resistant and flame retardant structural materials, product comprehensive performance safe and reliable;
- Ultra-low self consumption, permanent standby, light and beautiful. Installation diagram Table hole size / Bottom screw fixed /Schematic diagram after installation
Installation Diagram
Product Appearance
Packaging
- wireless charger*1
- Manual*1
Parameters
- Product name:Desktop wireless charger
- Product model: T02-C
- Input voltage:21-32V
- Input current:2.3-3.6A
- USB Output:40W
- Type-C Output:45W
- Wireless charging output:5W/7.5W/10W/15W
- Weight:955, Cable length:50cm
- Dimensions:Maximum diameter 77.8÷0.1mm,minimum diameter 70÷0.1mm, thickness 28.6#0.1mm
- Opening diameter :70÷0.1mm
- Wireless charging indicator :1 red LED+1 blue LED
- Output port 1 Type-C, support PD/QC output
- Output port 2USB, support QC output
- Output port 3 wireless charging, support QI output
Product Guide
- Power supply (input) usage
- this product is DC power supply, directly connected to the power supply can automatically start;
- power supply need meet the output electrical parameter requirements of the product ;
- Discharge (output) use method
- This product has the insertion detection function, connect the mobile phone or laptop pc and other electrical appliances to this product Type-C, USB port, can automatically identify and start to charge electronic products;
- After the power is turned on, the wireless charger enters the standby state, and the mobile phone or other wireless load, flat paste Placed on the wireless charging area, it can automatically connect and start charging;
- Use wireless charging to charge your device:
Before using this function, ensure that the device to be charged supports wireless charging. Devices that will need to be charged Place it flat in the wireless area of the charger, that is, the area printed with the wireless transmission signal, as shown in Figure 1. Need to top up The contact distance between the electrical equipment and the charger is required to be between 2-6mm, such as the mobile phone case More than 6mm thick, you need to remove the phone case to use wireless charging.
Note: This product is support fast charge model (7.5W/10W/15W), you need to connect an adapter of QC3.0 to reach fast charging function.
Lamp Description
overcurrent protection / short circuit protection
- If the port output/input current exceeds the protected value due to improper use or other factors, the product will automatically Switch off the output/input to protect the safety of the power supply itself and the appliances used;
- After the overcurrent state is lifted, can automatically return to normal working state;
- If it cannot be automatically restored, can be automatically activated after you remove the power supply and turn on again;
Precautions
- This product does not have waterproof function, it is strictly prohibited to clean the charger with a wet cloth or put it in water Avoid leakage, short circuit or other faults;
- It is strictly prohibited to short-circuit the charger, disassemble it by itself or throw the product into the fire, otherwise it will cause the equipment to catch fire or bBurst, causing an accident;
- Do not expose the charger to sunlight or wet, rain environment for a long time, and try to avoid it For use in such environments.
- Do not charge the phone in a closed environment, so as not to cause poor heat dissipation Hot and mobile phones, reduce the service life of chargers and mobile phones, lead to damage, and even cause smoke, Fire and other hazards. If there is an odor, hot, deformation, etc., during the use of the charger If the device is abnormal, stop using it immediately
- Wireless charging process may make the product local heat, is a normal phenomenon.
- Mainstream electronic products have been tested (such as Apple, Samsung, LG, HTC, etc.), the charging process is not You can lose your charge or overheat.
- Do not put metal objects in the wireless transmission area of the charger (such as metal mobile phone holder).
- Do not use the USB output and wireless charging at the same time, otherwise the charge may fail or the product is abnormal.
- The use of this product requires custom tables with round holes with a diameter of 70mm.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>