KOOL-IT KSM-36-KGM-36 Upright Display Cooler Instruction Manual
- June 15, 2024
- KOOL-IT
Table of Contents
KOOL-IT KSM-36-KGM-36 Upright Display Cooler
Please read these instructions completely before operating the units.
SAFETY PRECAUTIONS
- To ensure proper use, please thoroughly study these SAFETY PRECAUTIONS before operating the Unit.
- The purpose of the safety precautions in this manual is to ensure safe and correct use of the unit to minimize risks that could cause serious damage and injury to you or other persons. The safety precautions are divided into WARNINGS and CAUTIONS. Cases where improper handing of the unit could lead to death or serious injury are listed under the “AWARNING’ heading. However, the cases listed under the ‘CAUTION” heading could also lead to serious results. To ensure the safety, adhere strictly to both types of safety precautions.
- Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
- This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
- Do not damage the refrigerant circuit.
- WARNING Improper handling of the unit could lead to death or serious injury.
- CAUTION Improper handling of the unit could lead to serious results depending on the circumstances.
- Text set off by the exclamation mark ® contains information that should be strictly adhered to.
- After reading the instruction manual, store it an easily accessible place where the users) of this product can easily find it.
PRECAUTIONS FOR INSTALLATION
WARNING
Installation should be performed only by the dealer or a qualified expert.
Attempting to install the unit yourself could result in water leakage,
refrigerant leakage, electrical shock, or fire.
PRECAUTIONS FOR USE
HOW TO USE
BEFORE USE
- Remove the shipping package, tape, etc, and leave doors open and ventilate for a while.
- The unit is cleaned before shipment. However, clean the compartment interior after delivery.
- Please insert a power supply plug into the wall outlet, single-phase to cat voltage.
- Allow the unit to operate for about 1 hour to cool the compartment before placing items in the cooler.
WAIT 5 MINUTES OR MORE BEFORE RE-STARTING
- Restarting the unit immediately after it has been turned off may cause fuses to blow and activate the circuit breaker, the compressor may be overloaded, and/or other damage may occur.
DRAIN TRAY
- Defrosting is performed automatically and drain water is collected in the drain tray.
- Water in the drain tray is evaporated automatically. In humidity, there is a large amount of water in the drain tray, so please throw away drain water once a day.
EFFICIENT USE
- To prevent cold air from escaping, open and close the door quickly and keep the door open for as short a time as possible.
- Please install the unit in a well-ventilated place.
SHELF HEIGHT ADJUSTMENT
The shelf height can be adjusted. Arrange the shelves under the dimensions of
the items to be placed in the cooler.
TEMPERATURE ADJUSTMENT
For the showcase cooler, the interior temp. during fully loaded at the factory
default setting of position at 4-5 will be kept at 0-10’C., If the ambient
temp. is extremely high or the stuffing food inside is too much, which might
cause the interior temp. a little bit higher. So, it would be better turn the
thermostat right so as to maintain the right temp. On the opposite, if the
ambient temp. is very low or empty loaded, or in less food storage, the
interior temp. might be able to reach minus 0’C, and in return to cause the
evaporator ice up; Thus, it would better switch the thermostat back to left to
relieve something.
CONTROL ON KSM SERIES ECS-180 instructions
Here are the instructions to change Celsius Degrees to Fahrenheit degrees:
Step 1
To make the manipulations easier, refer to the buttons as follows:
- First, you need to press the “D” button for at least 10 seconds until “HO” appears. Then you need to press “D” again a couple of times (to go down) until “H7” appears.
- Then, press the “C” button to show “Dr”. That means the change has been made from Celsius to Fahrenheit.
- As soon as the setting has been changed, the “E2” alarm will appear, we will go to step 2 for the next step.
Step 2
- To cancel this alarm, press the “A” button for at least 3 seconds to enter settings (“St” will appear). At this point, press “A” again to change the value of temperature from 3 to 37 (in Fahrenheit degrees) and press set to save the change, it will bring you back to “St”. Then, press the “B” button (to go up) until you see “PO”. Then press “A” and digits”00″ will appear. At this step, the menu requires a password which is 55. Press “B” until it reaches the proper number and then press “A” to confirm, it will bring you back to “PO”. Then, to cancel the E2 alarm, press the “B” button until you see the settings.
“D1” then press “A” button to enter the settings and change the settings to “00” and confirm by pressing “A” and the alarm is cancelled. It will bring you back do “D1”. You need to go up to the settings “C 1” Here is a menu of what needs to be changed when you switch from Celsius to Fahrenheit, the rest remain the same.
- Every time you get to a setting (“C1” as example), press the “A” button to access the value and use the “B” and “D” to go up (B) or down (D). After changing the value, always press “A” to save the change of values. You repeat the operation for all the settings included in the previous table and the rest is all default and doesn’t need any change.
- After all the changes were made, you just need to wait 10 to 15 seconds, and it will switch back to the temperature display. At that point, the changes have been made and will remain in the controller.
Here are the direct instructions on how to adjust the set point on the ECS-180 temperature controller:
- Locate the set button (button A). First, press and hold that button for 3 seconds until the letters “St” will appear and release.
- Press set (A) and release one more time to access the set point.
- To change its value, use the “B” button to raise it and the “D” button to lower it*
- When the desired set point is reached, press “set” (A) again one more time to confirm the change and allow 15 to 20 seconds until the controller saves the change and goes back to the temperature display on itself.
Please note that this machine has an internal temperature differential that works as a protection for the compressor. The way the differential works is that at whatever temperature the unit will be set at, the compressor will work and cool the cabinet down until it reaches the chosen set point then it will shut itself up. It will allow a differential of 4 degrees before starting its operation back. The reason is to protect the compressor from doing short cycles (on/off) repetitively. Doing so can burn out the compressor, the same as flickering the alight switch very fast, it will burn the light bulb. The compressor works the same so it should be considered when adjusting the set point.
PLACING ITEMS IN THE SHOWCASE
This showcase employs a forced circulation of the cold air system. If the
circulation of cold air is obstructed, the items will not be adequately
refrigerated. Pay attention to the following points:
- Do not let items obstruct the cold air inlet and suction outlet.
- Place items so that they do not protrude from the shelves. The gap between the shelves and the door is used for the circulation of cold air.
- Place items evenly on all shelves.
- Please do not display goods on the bottom. Please put goods on the shelf. Commercial refrigeration display cooler.
- This showcase be used with rated voltage ( 110V) and frequency(60Hz).
- This equipment is intended for the storage and display of non-potentially hazardous bottled or canned products only.
- This display refrigerator is not for the display of potentially hazardous foods.
CLEANING
WARNING To prevent any electrical shock hazards or injury by rotating the circulation fan, always disconnect the power cord plug from the wall outlet before cleaning.
EXTERIOR AND COOLER COMPARTMENT
Wipe with a soft, dry cloth. If very soiled, wipe with a cloth that has been moistened with a detergent • Then wipe with a cloth that has been dipped in water.
WARNING: Do not splash water directly onto the cooler and do not wash with water. Short-circuit and electrical shock could result.
- Clean the cooler regularly to keep it clean at all times.
- Never use polishing powder, soap powder, benzine, oil or hot water as these will damage the painting and Volastic components.
CHECKS
To ensure the safety, perform the following checks after cleaning.
- ls the power cord plug firmly inserted into a dedicated wall outlet? Confirm that the plug is not abnormally hot.
- Check the power cord for cracks and damage. Should the slightest irregularity be observed, contact the dealer from whom you purchased this unit or our customer’s service.
IN CASE OF THE FOLLOWING
POWER FAILURE
Keep opening and closing of the door to a minimum. Avoid placing new items in
the cooler as this will raise the temperature inside the compartment.
WHEN NOT USED FOR A LONG PERIOD
Remove all items from the compartment and disconnect the power cord plug from
the wall outlet. Clean the compartment interior and wipe away all water. To
prevent mold formation and bad smell, leave the door open to dry the
compartment completely.
TRANSPORTATION
Disconnect the power cord plug from the wall outlet. When moving the cooler,
make sure that the feet do not damage the power cord. Do not let the feet hit
against floor steps, thresholds, etc.
TEMPORARY STORAGE
Affix a piece of wood, etc. Between the door and main unit to prevent complete
closing of the door. Make sure not to store the unused cooler at a location
where children play. Should a child enter the compartment and the door is
closed, the child may not be able to open the door from the inside.
BEFORE REQUESTING SERVICE
Please check the following items if you encounter problems with the unit. If the problem continues after taking the proper remedial actions, disconnect the power cord plug from the wall outlet. Transfer the items stored in the cooler to a box or other container. Then contact the dealer from whom you purchased this unit and be ready to provide information as listed in “REQUIRED INFORMATION” below.
CAUTION
To prevent any electrical shock hazards, do not disconnect the power cord plug
from the wall outlet with wet hands.
BEFORE REQUESTING SERVICE
- No refrigeration at all
- Is the power supply interrupted?
- Is the power cord plug disconnected from the wall outlet?
- Are the shop’s power fuses blown and/or the circuit breaker activated?
- Inadequate refrigeration
- Is the temperature setting appropriate?
- Are items obstructing the cold air inlet and suction outlet?
- Are stored items packed too tight?
- Is the door open or is it opened and closed frequently?
- Is the condenser clogged?
- Excessive noise
- Are all feet in firm contact with the floor?
- Is the rear panel of the cooler contacting the wall or other objects?
- Are other objects in contact with the cooler?
- Condensation on cooler exterior
- Condensation may condense on the exterior and door during hot and humid days or depending on the place of installation. This occurs when the humidity is high and water particles in the air contact cold surfaces. This is normal.wipe away condensation with a dry cloth.
Showcase sometimes stops running when the thermostat turns off.
REQUIRED INFORMATION
- Nature of malfunction (as accurately as possible)
- Product number
- Serial number
- Customer’s name, address, phone number
- Year and date of purchase
- 3560 NW 56th Street
- Fort Lauderdale, FL 33309
- Tel.: 786.600.4687 / Toll Free: 844.218.8477 Fax.: 786.661.4100
- 5659 Royalmount Avenue
- Montreal, Qc, Canada H4P 2P9
- Tel.: 514.737.9701 / Toll Free: 888.275.4538 Fax.: 514.342.3854 / Toll Free: 877.453.8832
KOOL-IT Is a registered trade mark of MVP Group. Specfflcatlons subject to change wtthout notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>