PHENOM LIGHTING TECHNOLOGY 18581 Solar Cob LED Flashlight Instructions

SOLAR COB LED FLASHLIGHT
WITH WORK LIGHT FUNCTION

SOLAR COB LED FLASHLIGHT – WITH WORK LIGHT FUNCTION

• Non-slip, large handle
• Energy-saving XPE LED with directional light
• High-brightness COB LED for illuminating larger surfaces
• Solar panel built into the lamp body
• Rechargeable, high-capacity battery
• MicroUSB port
• Silicone cap
• IP55 protection
• Compact size

Lighting modes:

• 100% XPE LED flashlight mode
• Reduced XPE LED flashlight mode
• Flashing XPE LED flashlight mode
• 100% COB LED worklight mode

Never direct the light of the lamp towards another person or living being, because the bright light can cause partial or complete vision loss or eye injury!

Please read the following instructions carefully before using the appliance and keep them for future reference.

Safety warnings:

• Never direct the light of the lamp towards another person or living being, because strong light can cause partial or complete damage to eyesight or eye damage!
• Never look into the light beam when the lamp is on! If the light beam reaches your eyes, close your eyes immediately or cover your face! In case of injury or eye pain, consult your doctor!
• The device also has a flashing / alarm function that can cause epileptic symptoms in sensitive people! Please avoid flashing at other people.
• The device is used to illuminate objects and issue as SOS signal!
• Do not use the appliance indoors. The lamp is designed for residential use, hiking, outdoor hobbies!
• The device is not waterproof, only use it in accordance with the IP55 protection standard! IP55 = Dust protected (nondamaging intrusion allowed). Protected against splashing water from all directions (non-damaging leakage allowed)
• The IP protection of the lamp is said to be with the charging cover closed.
• If you do not charge the device battery or the device is not powered by the lamp, the charger cover must be kept closed to protect the charging ports and the indicator LEDs!
• The device has a built-in battery, which must be charged with the supplied cable or the built in solar panel. The charging adapter must be selected according to the specification. (standard 5V USB)
• The appliance must only be used in accordance with environmental factors: Only expose it to direct sunlight or heat sources for as long as is absolutely necessary until charging, keep it away from heaters and ovens.
• Please note during use that in cold environmental conditions, the lamp’s performance may be reduced due to a decrease in the built-in battery’s performance.
• The device cannot be disassembled! In the event of a fault, contact a specialist workshop!
• The built-in LED light source cannot be replaced! It is forbidden to disassemble the housing!
• Do not use the device near flammable, explosive materials.
• Do not insert any optical devices (eg magnifier, spectacle lens) into the light beam.
• The appliance must not be used by children! Not a toy!
• The lamp must be used for its intended purpose! The manufacturer and distributor are not liable for damage resulting from improper use!

Use: You can check whether the battery is charging under the connector cover on the top of the device. A flashing green light indicates that the battery is charging. You will also find the MicroUSB connector for charging the lamp there.
The flashlight can be switched on and off with the on / off button on the upper handle Before switching on, make sure that the light from the appliance is not directed at another person or animal. By pressing the button once, the device lights up at a high brightness, by pressing the button again you can reduce the intensity of the brightness, then by pressing the button again you can switch to a flashing light signal. The work light function can be activated by pressing the once more.
You can turn off the device by pressing the button again!
Charging the torch: The lamp must only be connected to a socket that complies with the specification (USB 5V )! A socket with a different voltage will cause damage to the lamp! Connect the supplied microUSB cable to the MicroUSB socket on the torch and then the other end to the USB charging socket.
The charging of the lamp’s battery is indicated by a flashing green indicator LEDIt takes at least 3 hours to fully charge the lamp (depending on the power of the adapter used for charging). Do not use the lamp for lighting while charging the battery!
Cleaning: If the lamp becomes dirty, clean the device with a slightly damp cloth. Do not use any chemicals or cleaning agents during the operation. Do not use abrasive or sharp cleaning tools! Make sure that the terminal cover is closed. Do not immerse the lamp in liquid!
Storage: Store in a place protected from sunlight, moisture. We recommend that if you won’t use the device for a long time to charge the built-in battery to maintain its performance. This increases the life of the battery.
Malfunction: In the event of a malfunction, contact a specialist! Do not disassemble the device! Repairs to the device may only be carried out with factory spare parts! The manufacturer and distributor are not liable for damage resulting from improper use!
Proper disposal of the appliance (Electrical appliance)
It is valid in the European Union and in all other European states that participate in selective collection According to Directive 2012/19 / EU, electrical waste and appliances must not be disposed of with household waste. Old appliances should be placed seperately to maximize the recycling of raw materials, thus reducing their impact on human health and the environment. The crossed-out wheeled bin symbol is attached to all products it requires to be collected separately. Consumers should contact local authorities and waste collectors for more information.

PRODUCT CODE:
18581

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>