Lingzhu SC116 Smart Camera User Manual
- June 15, 2024
- Lingzhu
Table of Contents
Lingzhu SC116 Smart Camera
Introduction
Thank you for purchasing Smart Camera. Get started using your new devices by downloading TuyaSmart, one convenient app that manages everything straight from your phone. Easily connect to your home Wi-Fi and control multiple devices from the touch of your fingertips.
What’s in the Box
-
Smart Camera x 1
-
USB Cable x 1
-
User Manual x1
-
Mounting Bracket x 1 *
-
Adapter x 1 *
-
Screw bag x1 •
-
: Different products have different accessories, please refer to physical packing.
Get Ready
- Know your Wi-Fi network and password
- Make sure your mobile device is running iOS® 11 or higher or Android™ 6.0x or higher
- Make sure you’re connecting to a 2.4GHz Wi-Fi network (It can’t connect to 5GHz networks)
-
Register an account on your TuyaSmart app
STEP 1.
Enter your mobile phone number or email address.
STEP 2.
Enter the verification code and create a password.
Plug In
How do I reset my device?
- Press the Reset Button (as Pie 1) for several seconds until camera starts to beep.
- Optional: Insert Micro SD card as shown in Pie 1.
Add Device
-
Open TuyaSmart APP, click “+” on the top right corner of the page “HOME”, then select “Smart Camera”.
-
Make sure the indicator light on the device is flashing red quickly, then press “Next Step”.
-
Read the instruction about “Scan with the camera”, click “Continue”.
-
Scan the QR Code on your phone with camera. Heard a prompt tone, click “Heard the beep”.
-
When the indicator light on the device turns from flashing red light to steady green light, the network configuration is complete.
*Please refer to the specific APP interface if there are any difference.
Frequently Asked Questions
Can I share with family and friends?
What's the Wireless Range?
The range of your home Wi-Fi is heavily dependent on your home router and the conditions of the room. Check with your router specifications for exact range data.
How many cameras can I control?
TuyaSmart app can control an unlimited amount of devices in an unlimited amount of locations. Your router may have a limit of how many devices can be connected to one router.
My device can’t be connected to network with App
- Make sure the device is under the config status (indicator light is flashing quickly)
- Make sure the Wi-Fi is available and not too far away from router
- Make sure the Wi-Fi password you input is correct
My device shows offline in my App
-
Make sure the device is powered on
-
Make sure the network is stable and the Wifi name and password not modified. If not, add device again.
-
If the network is normal, but it’s still offline. Check if there are too many Wifi connections. You can restart your router to check the status of the device.
-
You can find much more useful information in the Help Center on App.
-
It is recommended that the device be installed at a height below 2M.
-
Operating temperature -10 ~ 45 C , Operating humidity ≤95%
-
Frequency Range : 2.412~2.462GHz, RF Output Power: 17.5 dBm
Installation Instructions
-
Take out all accessories and arrange them in order
-
Paste the positioning sticker on the installation area, such as the wall, ceiling or table, and drill 3 holes on the wall with a drill using a diameter of 6mm. Drive in three expansion screws in sequence to fully secure the
-
base.
Align the bottom of the camera’s main body, and aim to the right angle. -
Then rotate and snap it into the base until it is completely fixed. Insert the Micro-USS end into the camera interface, and connect the USS end to the adapter. Finally insert the adapter into the socket, then the device will run with power supply.
Technical Specifications
- Audio : Internal Speaker and Microphone
- Storage : supports up to 128G Micro SD card (not included)
- Wi-Fi : IEEE 802.11 b/g/n, 2.4GHz(not compatible with 5GHz Wi-Fi networks)
- Power : General 5V Direct Current 1 A, symbol ” ⎓ ” means direct current
Warning
Federal Communications Commission (FCC) Declaration of Conformity
FCC Caution : Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules.Operation is subject to the
following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled rolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator and your body.
Important Note
This radio module must not installed to co-locate and operating simultaneously
with other radios in host system except in accordance with FCC multi-
transmitter product procedures. Additional testing and equipment authorization
may be required to operating simultaneously with other radio.
The availability of some specific channels and/or operational frequency bands
are country dependent and are firmware programmed at the factory to match the
intended destination. The firmware setting is not accessible by the end user.
Declaration Of Conformity European Notice
Hereby, Ningbo Lingzhu Technology CO., Ltd. declares that this product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU,2011/65/EU.
This product must not be disposed of as normal household waste, in accordance with EU directive for waste electrical and electronic equipment (WEEE- 2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.
The device could be used with a separation distance of 20cm to the human body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>