DONGFXK M100-pro Motorized 100 Percent Blackout Roller Window Shades Instruction Manual
- June 15, 2024
- DONGFXK
Table of Contents
DONGFXK M100-pro Motorized 100 Percent Blackout Roller Window Shades
Instruction Manual
-
Tuy
Hub not included
-
Fast Setup
-
External Battery Rod Supported
-
Quiet Motor
Details of Parts Included in Package
-
Motorized Shade
-
Remote
-
Install Hardware **
**
Battery Installation
-
Open the battery cover
-
Install the battery in the battery compartment.
-
Connect the power plug of the shade to the battery socket.
-
Close the battery cover
Change the Battery
-
Remove the shade
-
Open the battery cover.
-
Take out the battery compartment and replace the battery. Then put it back.
-
Close the battery cover.
-
Install the shade on the bracket.
Installations Guide
We provide two installation methods:
- No drill installation
- Drill installation.
No drill Installtion
Inside Mount: No Tools-No Drill design allow it no need to drill any holes on your window frame, easy to install
We provide 3 widths of the extension blocks.
NOTICE: Do not paste two expansion blocks together for use.
Select an extension block with appropriate thickness and paste it to the shade motor end.
1/8″| W ≤ 1/4″
1/4″| 1/4″ W ≤ 1/2″
1/2″| 1/2″ W ≤ 1″
-
Push the shade to the left and pressed against the wall.
-
Push up the right end of the shade and put it into the window frame.
-
Tighten the safety lock.
Drill Installation
(You can decide the inside mount or outside mount according to your own needs.)
Inside Mount
-
Decide on and mark the positions of the two brackets with a pencil, using pencil marks as a guide. (We suggest marking at 1/3 and 2
-
Drill holes at marked locations.
-
Hook the headrail of the shade into the front of the bracket rotate the headtail until the back of it securely snaps into place.
Outside Mount
-
Decide on and mark the positions of the two brackets with a pencil, using pencil marks as a guide.
-
Drill holes at marked locations.
-
Hook the headrail of the shade into the front of the bracket rotate the headtail until the back of it securely snaps into place.
NOTICE
- Please read the installation instructions carefully to familiarize yourself with safe and effective usage before use. In addition, keep the installation instructions handy when using the product.
- The brackets and screws apply to the wooden window frames, plasterboard walls and concrete walls, but they cannot be installed onto the window frames or ceiling which are not made up of wood, plasterboard and concrete.
- Please check the materials and hardness of the window frames or ceiling before installation.
- Make sure to comply with the quantity of brackets and installation location required in the installation instructions when installing the products. Improper installation could cause the shades dropping and bring damage to health or property.
- Please do not hang any items on the product or pull the product roughly or fiercely.
- The product is only suitable for indoor use and not for outdoor use.
- Please do not use the product in a high heat or humid environment (such as saunas or furnace), or near an open flame.
- Please close the window or push the shades up during high winds, otherwise the strong winds could cause the damage to the product or an accident.
- Please do not place any items which can interfere with operating the shades within a range of moving up and down.
Function Key Description
Please refer to the manual according to the purchased remote control model.
Motor
Remote
Front
1-Channel remote AC2100-01A
Back
The shades have been adjusted to the best condition before delivery, so they do not need to be adjusted again. If you want to adjust, please refer to the following advanced setting functions
Quick Matching
Please refer to the manual according to the purchased remote control model.
Swtich the remote to “admin” state
Step 1
Make sure the motor is energized. Select the channel you want to match.
(single channel remote control doesn’t need to select.)
Step 2
Hold the M key of the shades for two seconds, and the motor of the shades
rotate forwards and backwards once to active;
Step 3
Hold the S key of the remote for two seconds, and the motor of the shades
rotates forwards and backwards once to indicate that the remote and the shades
are linked;
Step 4
Use the up button on the front of the remote to set the highest upper position
to a proper position, and then press pause button to stop.Hold the upward
arrow on the back of the remote for 2 seconds, and the motor rotates once to
lock the position of the highest upper position ;
Step 5
Use the down button on the front of the remote to set the lowest bottom
position to a proper position, and then press pause button to stop.Hold the
down arrow on the back of the remote for 2 seconds, and the motor rotates once
to lock the position of the lowest bottom position.”
In admin mode, you can switch between inching operation and continuous operation, to adjust the shades more accurately
Press once,the shades will be in inching operation.
Press twice,the shades will be in continuous operation
Advanced Settings
Please refer to the manual according to the purchased remote control model.
“admin”mode
Remote channel shows slow flash
Motor reversing
The running direction of the shades is oppsite to what shows on the remote
button.
Method 1
Press both together until the motor rotates once
Method 2
Press M key 10” motor rotates three times
Delete remote matches
- Select the switch to “admin” mode
- Press “S” 5 times, motor rotates once.The match is deleted.
“user” mode
In user mode, you can operate and use this product normally without worrying
about any mis operation to the motor.
Add a new remotes
A motor can match one or more remotes remotes need to be matched. See“ remote
quick matching”
There’s a quick way to copy it
-
Select the switch to “user” mode
-
Operate the matached remote (remote 1). (Select the channel you want to copy.)
Press”S” 1 time, motor rotates once
Press”S” 1 time again, motor rotates once -
Operate the remote 2 (new one) to be added. (Select the channel you want to add)
Press”S” 1 time, motor rotates once Copy complete.
Pairing channel
Please refer to the manual according to the purchased remote control model
One channel of a remote controls one motor, and 15 channels control up to 15 motors. For example, the 15 channel remote is only used 1-5 channels, the rest of 6-15 channels are not used and can be hidden without display
-
The remote shows the channels. Press and hold two channel switch keys at the same time. And the remote shows “L” at first, and then shows “15”. Release the keys.
-
Use channel switch button to select the channels which have to be reserved, from channel 1.}
-
use the “pause” key to confirm the channels to be reserved.
Reserved channels can only be counted from channel 1. For example, 1-5. No support for 3-7. Repeat the operation to adjust the final required number of channels.
Motor”M”Key| Operation| The motor feedback| Function
---|---|---|---
Press for 2”| Motor rotates once| The motor enters the matching state
Press for 5”| Motor rotates twice| \
Press for 10”| Motor rotates three times| Motor reversing
Press for 15”| Motor rotates four times| Restore the factory settings
Motor indicator light| Motor indicator light| Reason
---|---|---
Quick Flash| Low Battery
Slow Flash| Charging
Light From On to Off| Charging>90%