LOQRON 9902 Front Door Handle Set Installation Guide
- June 15, 2024
- LOQRON
Table of Contents
- LOQRON 9902 Front Door Handle Set
- Product Information
- Frequently Asked Questions (FAQ)
- Tools Required for Installation
- Parts in the Box
- Drill Holes
- Adjust the Deadbolt Latch
- Install the Latches and Striking Plates
- Install Exterior Lock
- Install Interior Lock
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LOQRON 9902 Front Door Handle Set
Product Information
Specifications:
Applicable door thickness: 35-45mm
Parts Included in the Box:
- Exterior Panel
- Interior Door Lever
- Thumb Knob
- Deadbolt Latch
- Entry Door Latch
- Striking Plate A (use for Deadbolt Latch)
- Striking Plate B (use for Entry Door Latch)
- Striking Plate Box A (use for Deadbolt Latch)
- Striking Plate Box B (use for Entry Door Latch)
- Fixing Ring
- Screw A(20mm) – 8pcs
- Screw B(45mm) – 2pcs
- Screw C(35mm) – 3pcs
Tools Required for Installation:
- Measuring Tape
- Electric Drill
- 2Hole Boring Saw
- 1 Drill Bit
- Phillips Screwdriver
Drill Holes:
If the door is pre-drilled, or if it is a replacement, skip this step and
proceed to “Adjust the Deadbolt Latch”. Otherwise, follow the steps below:
- Insert the latches into the holes and mark the outline of faceplates.
- Chisel 1/8 inch deep holes.
Adjust the Deadbolt Latch:
- Pull the block to extend the tongue.
- Rotate down.
- Pull the block back to retract the tongue.
Install the Latches and Striking Plates:
- Install the Deadbolt Latch and use Striking Plate A and Striking Plate Box A.
- Install the Entry Door Latch and use Striking Plate B and Striking Plate Box B.
- Secure the latches with Screw A (8pcs).
Install Exterior Lock:
- Fix the connecting column in the screw hole at the bottom of the panel using the recommended middle screw hole.
- Install the fixing ring.
- Insert the locking lever into the deadbolt latch and insert the spindle into the entry door latch. Ensure the deadbolt latch tongue is retracted.
Install Interior Lock:
- Secure the thumb knob with Screw B. Ensure the locking lever is vertical.
- Secure the door lever with Screw C.
- Secure the gasket with Screw C.
Frequently Asked Questions (FAQ)
-
What is the applicable door thickness for this product?
The applicable door thickness for this product is 35-45mm. -
What tools are required for installation?
The tools required for installation are a measuring tape, electric drill, 2Hole Boring Saw, 1 drill bit, and a Phillips screwdriver.
Tools Required for Installation
Parts in the Box
Drill Holes
(For pre-drilled door, or replacement, please skip to Adjust the Deadbolt Latch)
-
STEP 1
Fold the template at the dotted line and tape the template to the interior side of the door at 34-48 inch Height. -
STEP 2
- Mark the 2⅜ ” or 2¾”(60 or 70mm) hole center as A1 for the backset.
- Mark a point as A2, 5½” above A1 .
- Mark a point as C, about 9” below A1.
- Measure the thickness of the door and mark the middle point of the door thickness as B1.
- Mark a point as B2, 5½” above B1.
Note: Make sure the A1 and B1(A2 and B2) are at the same height.
-
STEP 3
- Drill two Dia. 2⅛” holes for the lock bodies at point A1 and A2.
- Drill two Dia. 1” holes for the latches at point B1 and B2.
- Drill a Dia. 3/8” hole for the connecting column at point C.
-
STEP 4
- Insert the latches into the holes and mark the outline of faceplates.
- Chisel 1/8” deep holes.
-
STEP 5
- Close the door with the latch installed and mark lines on the jamb as picture shown left.
- Align the striking plates with the lines. Draw the shape of striking plates.
- Drill 1 deep hole in the middle of the striking plates.
- Chisel ¹⁄8 ”(3mm) deep for the striking plate.
Adjust the Deadbolt Latch
The latch is initially set for 2⅜”(60mm). Switch to 2¾”(70mm), if your backset is 70mm.
Install the Latches and Striking Plates
Install Exterior Lock
- Fix the connecting column in the screw hole at the bottom of the panel. The middle screw hole is recommended.
- Install the fixing ring.
- Insert the locking lever into the deadbolt latch and insert the spindle into the entry door latch. Ensure the deadbolt latch tongue is retracted.
Install Interior Lock
- Secure the thumb knob with Screw B. Ensure the locking lever is vertical.
- Secure the door lever with Screw C.
- Secure the gasket with Screw C.