WASJOYE E217 Security Home Safe Instructions

WASJOYE E217 Security Home Safe

Specifications

• Model: E217
• Power Source : 4 x 1.5V AA batteries
• Emergency Power Source: Battery-operated emergency power box
• Keypad: Numeric keypad with # and * buttons
• Lock Type: Tubular lock with emergency key

The First Opening

1. Take out the tubular emergency key from the plastic bag.
2. Insert the tubular emergency key counter-clockwise into the lock hole.
3. Turn the key, then turn the knob to open the door.
4. Put 4 batteries of 1.5V AA battery in the battery box (on the back of the door).
5. Leave the door open and take the keys out.

Set or Change the Master Code

1. While the door is opened, press the button 00 twice.

2. Press the red reset button (on the left-side of back of door).
   The yellow light will be on.

3. Input any 3-8 digits you want, press # or * to confirm.

4. You will hear one beep, indicating that the new code has been accepted and stored.

Product schematic

The first opening

1. For the first opening, please take out the tubular emergency key from the plastic bag, insert the key into the lock hole, turn the key, then turn the knob to open the door. After that, put 4 batteries of 1.5V AA battery in the battery box(on the back of the door), then leave the door open and take the keys out. 1.Take out the tubular emergency key from the plastic bag.

2. Insert the tubular emergency key counter-clockwise as shown.

3. Turn the knob to open the door

Set the code

1. Set or change the master code
   • While the door is opened, press the button “0””0″(twice”0″), then press the red reset button (on  the left-side of back of door), the yellow light will be on, then input any 3-8 digits you want, press “#” or”*” to confirm, followed by one beeps, indicating that the new code has been accepted and stored.
2. Set or change the personal code
   • While the door is opened, press the red reset button(on the left-side of back of door), the yellow  light will be on, then input any 3-8 digits you want, press”#”or”*”to confirm, followed by 1 beeps, indicating that the new code has been accepted and stored.

Open the door

1. Input the code, followed by one beep and yellow light flashing, then press” #”or”*”to confirm, the green light will be on.
2. In 5 seconds, rotate the knob and pull out, the door will be opened.
3. Close the door, then rotate the knob left anti-clockwise to lock the safe.

Use the emergency box to open the door
When the battery is dead and the key is lost and the door cannot be opened ,the emergency box can be used to open the door.

1. Put the battery into the emergency power box.
2. Insert the plug of the emergency power box into the power hole (below the number keys).
3. Enter the password after booting successfully.

Main troubleshooting methods

1. If the safe has been used for a period of time, enter the correct password and the green light is on, but the safe cannot be opened, it may be that the battery is under voltage, which is not enough to provide suction. At this time, it needs to be replaced with a new battery.
2. If there is a “beep “sound emitted by the safe, it may be caused by the circuit board (circuit in the main board or panel) encountering water or moisture, or it may be caused by the corrosion of the battery or battery box which has not been used for a long time, replace the faulty parts according to the situation.
3.  According to the customer’s past usage, forgetting the set password is a common occurrence, so the management of the emergency keyis very important. Please do not put the emergency key in the safe. If the key is lost, you can contact the sales store to reissue the key for a fee.

Notice

1. If 3 incorrect codes input continuously, the keypad will be blocked about 20s with alarm sound for 20s. If another 3 incorrect codes input again after20s, the the keypad will be blocked about 300s with alarm sound for another 300s, and so on.
2.  If the yellow light turns on, indicating that you should change the batteries.
3. If you forgot the code or the batteries are run off, use the emergency key to open the safe as the first opening, and then press the reset button(on the left-side of back of door) to reset the code.
4. Any key pressed for 20 seconds, no subsequent key input into the sleep state, the front input cleared.
5.  The “*”and “#” on the operation pane have the same function to confirm.
6. The electronic part of the electronic safe will be short-circuited when it encounters liquids, and the product can not be placed in a humid environment. It is easy to cause the risk of circuit back-moistening and failure.
7. If you find that the safe can’t be opened by the key after not using it for long time, you can add lube to your keys and key locks.

Working conditions

1. Working power supply: four 1.5V AA alkaline batteries. Under-voltage(voltage less than 4.8 ±0.3V) will affect the magnet suction, which will cause the risk of difficult to open. When the red indicator on the panel lights up, remind you to replace the battery;
2. Working voltage range: DC 4.0-6.8V
3. Working current: <380mA
4. Static current: <5uA
5.  Use ambient temperature: -10″C-+70°C

If you need to wall mount the safe, install it as follows

1. Choose the place you want to install, use the impact drill to drill the expansion screw mounting holes on the wall and floor according to the sizeof the rear and bottom mounting holes.
2. Hammer the expansion tube into the hole.
3. Align the safe mounting hole with the extension hole.
4. Screw in the expansion screw from the box to complete the installation.

Recommended fixation method

MADE IN CHINA

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>