Laluce Natz 18x18W Waterproof LED Par Light User Manual

June 15, 2024
Laluce Natz

Laluce Natz 18x18W Waterproof LED Par Light

Before You Begin

What In the Box

  • 1 x18LEDs Waterproof Par Light
  • 2 x Bracket
  • 2 x Screw
  • 1 x User Manual

Unpacking Instructions

Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.

Caution

There are no user-serviceable parts inside the fixture. Do not open the housing or attempt any repairs yourself. In the unlikely situation, that your unit may require service, please contact us: at info@lalucenatzonline.com.

Disclaimer

LaluceNatz believes that the information contained in this manual is accurate in all respects. However, LaluceNatz assumes no responsibility and specifically disclaims all liability to any party for any loss, damage, or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident, or any other cause. LaluceNatz reserves the right to revise the content of this document without any obligation to notify any person or company of such revision, however, LaluceNatz has no obligation to make and does not commit to make any such revisions.

Safety Introductions

  • Please keep this User Manual for future consultation.
  • Unpack and check carefully there is no transportation damage before using the fixture.
  • Before operating, ensure that the voltage and frequency of the power supply match the power requirements of the fixture.
  • It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
  • Disconnect main power before servicing and maintenance.
  • Use a safety chain when fixing this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
  • Maximum ambient temperature is Ta: 104℉/40℃. Don’t operate it where the temperature is higher than this.
  • In the event of a serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type of spare parts.
  • Do not connect the device to any dimmer pack.
  • Do not touch any wire during operation and there might be a hazard of electric shock.
  • To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
  • The housing must be replaced if they are visibly damaged.
  • Do not look directly at the LED light while the fixture is on.

Product Overview & Size

Setup

AC Power

The LED Par Light has an auto-ranging power supply and it can work with an input voltage range of 110 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.

Mounting

  • Before mounting the product, read and follow the safety recommendations indicated in the.
  • Safety Introductions.

Orientation
The LED Par Light may be mounted in any position; however, make sure adequate ventilation is provided around the product

Operation

Control PanelOperation

  • To access the control panel functions, use the four buttons located underneath the display.
Button Function

|

Select an operation mode or back out of the current menu option

| Scroll up the list of options or select a higher-value

|

Scroll down the list of options or select a lower-value

|

Activate a menu option or a selected value

  • A. MWNU
  • B. UP
  • C. DOWN
  • D. ENTER

System Menu

display mode function declaration
A001(A001-A512) address code
CHND (6CH/10CH) 6/10channelmode
CL01 (CL01 CL32) Static color mixing mode (32 kinds)
CC99 (CC01-CC99) Jump mode
EE99 (EE01-EE99) Mutation pattern
FF99 (FF01-FF99) Gradient mode
ST99 (ST01-ST99) Confirm FM flash color (32 kinds)
SOU1(SOU1/2/3/4) Voice control mode SOU1 voice control jump SOU2 voice

control mutation

SOU3 voice-controlled color-changing stroboscopic Sou4 vice control jmp+mutation+color change strobe

R255 (R000-R255)| R manual dimming
G255 (G000-G255)| G manual dimming
B255 (B000-B255)| B manual dimming
W255 (W000-W255)| W manual dimming
Y255 (Y000-Y255)| Y manual dimming
P255 (P000-P255)| UV manual dimming
T000 (OFF/60-100)| Panel temperature display, preset power reduction setting (factory default 60 degrees)

Remarks

  1. ln A001mode, press the confirmation key to automatically enter the current adjustment mode, the up and down keys to adjust the value, and the confirmation key to adjust the color, After the parameters are adjusted, press the menu key to return, and press the confirmation key to adjust the machine.
  2. This version supports the RDM function.

DMX Mode

6CH Value Description
1 0-255 Red dimming
2 0-255 Green dimming
3 0-255 Blue dimming
4 0-255 White dimming
5 0-255 Amber dimming
6 0-255 UV dimming

DMX512 10-channel description

10CH Value Description
1 0-255 Total dimming
2 0-255 Red dimming
3 0-255 Blue dimming
4 0-255 Green dimming
5 0-255 White dimming
6 0-255 Amber dimming
7 0-255 UV dimming

8

| 0-10| Lights off
11-255| Strobe speed(slow-fast)

9

| 0-9| Lights off
10-50| Color mixing mode
51-100| Hopping mode
101-150| Gradient mode
51-200| Mutation pattern
21-220| Console jump voice control
21-240| Console color-changing stroboscopic sound control
21-255| Console mutation voice control

10

| 0| Lights off
1-255| Speed (slow to fast)

DMX Connection

DMX Signal Connection

3-Pin XLR to 5-Pin XLP Conversion

Conductor| 3-Pin XLR Female (OUT)| 5-Pin XLR Male (IN)
Ground/Shiela| Pin 1| Pin 1
Data Compliment (-signal)| Pin 2| Pin 2
Data True (-signal)| Pin 3| Pin 3
Not Used|  | Pin 4-Do Not Used
Not Used|  | Pin 5-Do Not Used

TECHNICAL SPECIFICATIONS

  • Power: 18LEDs x 18-Watts
  • Voltage: AC110-240V, 50/60Hz
  • LED: 18LEDs x 18W RGBWA+UV 6in1
  • Color: RGBWA+UV
  • Beam Angle: 45°
  • Dimmer: 0-100% Linear Dimming
  • Operation Mode: Jump, Fade, Strobe, DMX512, Sound, Master-slave
  • Channel: 6CH/10CH
  • Size: 11x10x7in
  • Weight: 8lb

info@lalucenatzonline.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals