Hygena LIB0139256D Stainless Steel Cap Hood Instruction Manual
- June 15, 2024
- Hygena
Table of Contents
Hygena LIB0139256D Stainless Steel Cap Hood
Product Information
Specifications
- Model : Unknown
- Languages : IT, EN, DE, FR, NL, ES, NO, LT, LV, SR, SL, HR, MK, TR, AR
- Mounting and Use Instructions available in multiple languages
Product Usage Instructions
Installation and Setup
Before starting the installation process, make sure to read and understand
all the instructions provided in this manual.
- Mounting : Follow the specific mounting instructions for your model. Ensure that all necessary accessories are included and properly installed.
- Connection : Connect the appropriate tubing to the corresponding connector on the product. Make sure the connection is secure.
Operating Modes
This product has two operating modes: aspirating (A) and filtering (F).
- Aspirating Mode : Ensure that the selector G is in the aspirating position (A) before using the product in this mode.
- Filtering Mode : If you prefer to recycle fumes and vapors, set the selector G to the filtering position (F).
Maintenance and Safety
Regular maintenance is essential to ensure the proper functioning and
safety of the product.
- Cleaning : Clean the product internally and externally at least once a month. Follow the cleaning instructions provided in this manual.
- Filter Replacement : Replace and clean filters as recommended in the maintenance instructions. Failure to do so may result in fire hazards.
- Safety Precautions : When using the product together with other gas or fuel-burning appliances, ensure proper ventilation and take necessary safety precautions.
Additional Usage Tips
- Lamp : Only use the specified lamp type mentioned in the lamp replacement section of this manual.
- Cooking : Exercise caution while frying to prevent oil overheating and potential fires.
- Hot Surfaces : Be aware that surfaces of the product may become hot during operation. Avoid direct contact to prevent burns.
Frequently Asked Questions (FAQ)
-
Q: Can I use this product with gas or fuel-burning appliances?
A: Yes, you can use this product together with other gas or fuel-burning appliances. However, ensure proper ventilation and follow safety guidelines. -
Q: How often should I clean the product?
A: It is recommended to clean the product internally and externally at least once a month. Follow the cleaning instructions provided in the manual. -
Q: What should I do if the lamp needs replacement?
A: Refer to the lamp replacement section in the manual for instructions on how to replace the lamp. Use only the specified lamp type. -
Q: Can I recycle this product?
A: Yes, this product should not be treated as domestic waste. Please dispose of it at an appropriate collection point for recycling of electrical and electronic equipment.
Note: the elements marked with the symbol “(*)” are optional accessories supplied only with some models or elements to purchase, not supplied.
- Check (for transport reasons) that there is no other supplied material inside the hood (e.g. packets with screws (), guarantees (), etc.), eventually removing them and keeping them.
- Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. This appliance is intended to be used in household and similar application such as
- staff kitchen areas in shop, offices and other working environments;
- farm houses; – by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments.
- The hood is supplied with an upper air outlet (A1 – attachment to bayonet fitting + screw) for exterior fume extraction (Aspiration version A), remove the corresponding removable metal panel and install the tube connector.
- Check that selector G is in suction position (A). If it is not possible to discharge the cooking fumes and steam outside, the filtering version hood can be used, mounting a carbon filter (*). The fumes and steam are recycled through a front grill placed over the command panel (do not remove the pre-fractural walls!). Check that selector G is in filtering position (F).
Caution
-
Before any cleaning or maintenance operation, disconnect hood from the mains by removing the plug or disconnecting the mains electrical supply.
-
Always wear work gloves for all installation and maintenance operations.
-
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
-
Children shall not be allowed to tamper with the controls or play with the appliance.
-
Cleaning and user maintenance shall not be made by children without supervision.
-
The premises where the appliance is installed must be sufficiently ventilated, when the kitchen hood is used together with other gas combustion devices or other fuels.
-
The hood must be regularly cleaned on both the inside and outside (AT LEAST ONCE A MONTH).
-
This must be completed in accordance with the maintenance instructions provided. Failure to follow the instructions provided regarding the cleaning of the hood and filters will lead to the risk of fires.
-
Do not flambé under the range hood.
-
Do not remove filters during cooking.
-
For lamp replacement use only lamp type indicated in the Maintenance/Replacing lamps section of this manual.
The use of exposed flames is detrimental to the filters and may cause a fire risk, and must therefore be avoided in all circumstances.
Any frying must be done with care in order to make sure that the oil does not overheat and ignite.
CAUTION : Accessible parts of the hood may become hot when used with cooking appliances. -
Do not connect the appliance to the mains until the installation is fully complete.
-
With regards to the technical and safety measures to be adopted for fume discharging it is important to closely follow the regulations provided by the local authorities.
-
The air must not be discharged into a flue that is used for exhausting fumes from appliance burning gas or other fuels.
-
Do not use or leave the hood without the lamp correctly mounted due to the possible risk of electric shocks.
-
Never use the hood without effectively mounted grids.
-
The hood must NEVER be used as a support surface unless specifically indicated.
-
Use only the fixing screws supplied with the product for installation or, if not supplied, purchase the correct screws type.
-
Use the correct length for the screws which are identified in the Installation Guide.
-
In case of doubt, consult an authorized service assistance center or similar qualified person.
WARNING!
-
Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.
-
Do not use with a programmer, timer, separate remote control system or any other device that switches on automatically.
-
This appliance is marked according to the European directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE).
-
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
-
The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal.
-
For further detailed information regarding the process, collection and recycling of this product, please contact the appropriate department of your local authorities or the local department for household waste or the shop where you purchased this product.
Appliance designed, tested and manufactured according to: -
Safety : EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC 62233.
-
Performance : EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO 5168; EN/IEC 60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3; ISO 3741; EN 50564; IEC 62301.
-
EMC : EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2; EN/IEC 61000-3-2; EN/IEC 61000-3-3. Suggestions for a correct use in order to reduce the environmental impact: Switch ON the hood at minimum speed when you start cooking and kept it running for few minutes after cooking is finished. Increase the speed only in case of large amount of smoke and vapor and use boost speed(s) only in extreme situations. Replace the charcoal filter(s) when necessary to maintain a good odor reduction efficiency. Clean the grease filter(s) when necessary to maintain a good grease filter efficiency. Use the maximum diameter of the ducting system indicated in this manual to optimize efficiency and minimize noise.
Installation
- The minimum distance between the supporting surface for the cooking equipment on the hob and the lowest part of the range hood must be not less than 50cm from electric cookers and 65cm from gas or mixed cookers.
- If the instructions for installation for the gas hob specify a greater distance, this must be adhered to.
- The template (*) can be used for installation.
Electrical connection
The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area, after installation. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area, after installation, apply a double pole switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over-current category III, in accordance with installation instructions.
WARNING!
- Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check that the mains cable is correctly assembled.
- Warning! If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard.
Operation
The hood is fitted with a control panel with aspiration speed selection control and a light switch to control cooking area lights.
Maintenance
- Clean using ONLY a cloth dampened with neutral liquid detergent. DO NOT CLEAN WITH TOOLS OR INSTRUMENTS. Do not use abrasive products. DO NOT USE ALCOHOL!
- Grease filter – Carbon filter (*): it is/they are mounted on the back of the grill and must be changed once a month. If the metal fats filter is envisaged in the model in your possession, this must be cleaned once a month with non-aggressive detergent manually or in a dishwasher at low temperature and short cycle.
- The metal anti-fats filter might discolour by washing in a dishwasher but its filtering characteristics do not change at all.
- Changing bulbs (Attention! Make sure that the bulbs are cool before touching them):
- Remove the grill.
- Replace the damaged lamp.
- Use E14 3W max LED lamps only. For more details, check enclosed leaflet “ILCOS D” (alfanumeric position “1d”).
LIB0139256D Ed. 12/22
- Points de collecte sur www.quefairedemesdechets.fr