SEIKAKU AXV_SYSTEM Pro Audio Speakers User Manual

SEIKAKU AXV_SYSTEM Pro Audio Speakers User Manual

Important Safety Instructions

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK PLEASE DO NOT REMOVE THE COVER OR THE BACK PANEL OF THIS EQUIPMENT.

THERE ARE NO PARTS NEEDED BY USER INSIDE THE EQUIPMENT, FOR SERVICE, PLEASE CONTACT QUALIFIED SERVICE CENTERS.

This symbol, wherever used, alerts you to the resence of un- insulated and dangerous voltages in the product enclosure. These are voltages that may be sufficient to constitute the risk of electric shock or death,

This symbol, wherever used, alerts you to important operating and maintenance instructions. Please read.

Protective Ground Terminal
AC mains (Alternating Current)
Hazardous Live Terminal
ON: Denotes the product is turned on.
OFF: Denotes the product is turned off.

Describes precautions that should be damage to the product.

1. Read this Manual carefully before o

2. Keep this Manual in a safe place.

3. Be aware of all wamings reported v

4. Keep this Equipment away from wa

5. Clean it only with dry doth. Do not u chemicals.

6. Do not damp or cover any cooling c equipment only in accordance with instructions.

7. Power Cords are designed for your: Ground connections! If the plug da outlet, seek advice from a qualified power cord and plug from any phys of electric shock. Do not place heav power. This could cause electric sho

8. Unplug this equipment when unus time or during a storm.’

9. Referal service to qualified service personnel only. Do not perform any servicing other than those instructions contained within the User’s Manual.

10. To prevent fire and damage to the product, use only the recommended fuse type as indicated in this manual Do not short-circuit the fuse holder. Before replacing the fuse, make sure that the product is OFF and disconnected from the AC outlet.
    WARNING
    To reduce the risk of electric shock and fire, do not expose this equipment to moisture or rain.|
    Dispose of this product should not be placed in municipal waste and should be separate collection.

11. Move this Equipment only with a cart, stand, tripod, or bracket, specified by the manufacturer, or sold with the Equipment. When a cart is used, use caution when moving the cart/ equipment combination to avoid possible injury from tip-over.

12. Permanent hearing loss may be caused by exposure to extremely high noise levels. The US. Government’s Occupational Safety and Health Administration (OSHA) has specified the permissible exposure to noise level. These are shown in the following chart.

According to OSHA, an exposure to high SPL in excess of these limits may result in the loss of heat. To avoid the potential damage of heat, it is recommended that Personnel exposed to equipment capable of generating high SPL use hearing protection while such equipment is under operation.

The apparatus shall be connected to a mains socket outlet with a protective earthing connection.

The mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

Introduction

The new cabinets have been designed to provide a cost effective high grade solution while maintaining high quality cabinet construction and optimum components.

Our Professional Audio Products are designed and tested by a highly qualified engineering team with more
than 20 years of experience. Great care is placed in delivering products with excellent performance, specifications and dependable reliability. Also great emphasis is placed in creating and bringing to market products that can fill multiple applications and also offer customers exceptional value.

Every audio product is strictly tested and complied to very strict standards.

Installation Tips

• • Speakers should be placed in a position that allows for unobstructed sound projection. In many instances it is beneficial for speakers to elevate on tripod stands to achieve maximum dispersion and reach. Consider speaker stand or equivalent to raise speakers.
• Using quality cables ensure best possible sound. Consider using 16 or 14 gauge cables or equivalent.
• For best results match the speakers to a good amplifier that matches the wattage and impedance of your speakers. Proper amplification power results in good quality audio and longer component life. Check out.
• Avoid pointing microphone directly at an amplified speaker otherwise could cause feedback possible damaging speaker components and your hearing.

Enjoy the sound!

Usefull Data

Please write your serial number here for future reference.

Serial Number:

Date of Purchase:

Purchased at:

Technical Specifications

AXV24.215 SYSTEM: AXV24.215 SUB+AXV24.215 SAT

AXV24.215 System

Frequency Response| 35Hz – 20KHz (-10dB)
Total Amplifier Power| 2000W Continuous / 4000W Program / 8000W Peak Class D @ 4 Ohms
Maximum SPL@1M| 134dB
Crossover Frequency| 200Hz
Dispersion(-6dB)| 130°Horizontal
Dimensions(WxHxD)| 460 x 2010 x 676mm (18.11” x 79.13” x 26.6”)
Net Weight| 50.15Kg (110.56 Ibs)
AXV24.215 SUB
System Type| 2 x 15″ Active Subwoofer Speaker Cabinet
Frequency Response(-6dB)| 35Hz – 180Hz
Total Amplifier Power| 2000 W Continuous / 4000W Program/8000W Peak Class D @ 4 Ohms
Amplifier, Subwoofer| 1000 W Continuous / 2000W Program/4000W Peak Class D @ 4 Ohms
Amplifier, Satellite| 1000 W Continuous / 2000W Program/4000W Peak Class D @ 4 Ohms
DSP Presets Modes| LIVE / Music / SPEECH / DJ
Electronic Protections| Over heat Protection/Short Circuit Protection/Digital Compressor
Cooling| Temperature-controlled fan
Connections| Input: 4 x Combo-XLR&1/4”, 1 x RCA In L&R, 1 x 3.5 Stereo Jack,Output: 1 x XLR Thru&Mixout, 1 x Speakon Satellite
External Controls| Volume Control/Switch for Input sens/Swtich for mode selector/Power ON with Green LED/Limiterwith Red LED/Ground Lift/OLED DSP Display and Control /IP Control/MP3 and BT(option)
Power Supply| 115V/230V ~50/60Hz Switchable
Enclosure Construction| Plywood Cabinet, Resistant Black Paint, Metal Grille with Foam, Rubber Feet, Integrated side handles
Mounting| Smart Mounting and Connection
Dimensions(WxHxD)| 460 x 830 x 676mm (18.11” x 32.67” x 26.6”)
Net Weight| 40.47Kg (89.22 Ibs)
AXV24.215 SAT
System Type| 24*3″ Passive Speaker System
Output Power| 480W Continuous, 960W Program, 1920W Peak
Sensitivity (1W/1M)| 99dB
Frequency Response(-6dB)| 150Hz-20kHz
Impedance| 4 ohms
Transducer Low| 3” Neodymium Fullrange Speaker, 0.8” (20.4mm) Voice Coil
Enclosure Construction| Aluminium Cabinet, Metal Grille, Resistant Paint
Connector| 2 Pin smart connection
Dimensions(WxHxD)| φ167 x 1170mm(φ6.57” x 46.06”)
Net Weight| 9.7Kg (21.38 Ibs)

Technical Specifications

AXV62.15 SYSTEM: AXV62.15+AX POLE+AXV62BM+AXV62TP

AXV62.15 System

Frequency Response| 40Hz – 20KHz (-10dB)
Total Amplifier Power| 1000W Continuous/2000W Program/4000W Peak Class D @ 4 Ohms
Maximum SPL@1M| 128dB
Crossover Frequency| 220Hz
Dispersion(-6dB)| 120°Horizontal
Dimensions(WxHxD)| 440 x 2015 x 640mm (17.32” x 79.33” x 25.20”)
Net Weight| 37.81Kg (83.35 Ibs)
AXV15SA
System Type| 15″ Active Subwoofer Speaker Cabinet
Frequency Response(-6dB)| 40Hz – 210Hz
Total Amplifier Power| 1000W Continuous/2000W Program/4000W Peak Class D @ 4 Ohms
Amplifier, Subwoofer| 500W Continuous/1000W Program/2000W Peak Class D @ 4 Ohms
Amplifier, Satellite| 500W Continuous/1000W Program/2000W Peak Class D @ 4 Ohms
DSP Presets Modes| LIVE / Music / SPEECH / DJ
Electronic Protections| Over heat Protection/Short Circuit Protection/Digital Compressor
Cooling| Temperature-controlled fan
Connections| Input: 4 x Combo-XLR&1/4”, 1 x RCA In L&R, 1 x 3.5 Stereo Jack,Output: 1 x XLR Thru&Mixout, 1 x Speakon Satellite
External Controls| Volume Control/Switch for Input sens/Swtich for mode selector/Power ON with Green LED/ Limiter with Red LED/Ground Lift/OLED DSP Display and Control /IP Control/MP3 and BT(option)
Power Supply| 115V/230V ~50/60Hz Switchable
Enclosure Construction| Plywood Cabinet, Resistant Black Paint, Metal Grille with Foam, Rubber Feet, Integrated side handles
Mounting| Smart Mounting and Connection
Dimensions(WxHxD)| 440 x 520.5 x 640mm (17.32” x 20.49” x 25.20”)
Net Weight| 26.1Kg (57.54 Ibs)
AXV Pole
Enclosure Construction| Aluminium Cabinet, Metal Grille, Resistant Paint
Connector| 2 x Electronic Adapter – 1 x Input Connector for Sub & Another with Input Connector for Satellite
Dimensions(WxHxD)| φ112.5 x 354mm(φ4.43” x 13.94”)
Net Weight| 1.36Kg (3.0 Ibs)
AXV 62BM
System Type| 6 x 3.5″ Passive Speaker System
Output Power| 180W Continuous, 360W Program, 720W Peak
Sensitivity (1W/1M)| 96dB
Frequency Response(-6dB)| 150Hz-20kHz
Impedance| 16 ohms
Transducer Low| 3.5” Woofer , 1.0” (25.4mm) Voice Coil
Rotation| 360 Degree Mechanical Adjustment
Enclosure Construction| Aluminium Cabinet, Metal Grille, Resistant Paint
Connector| 2 x Electronic Adapter – 1 x Input Connector for AX Pole & Another with Input Connector for AXV62TP
Dimensions(WxHxD)| φ112.5 x 609.7mm(φ4.43” x 24.0”)
Net Weight| 5.2Kg (11.46 Ibs)
AXV 62TP
System Type| 6 x 3.5″ Passive Speaker System
Output Power| 180W Continuous, 360W Program, 720W Peak
Sensitivity (1W/1M)| 96dB
Frequency Response(-6dB)| 150Hz-20kHz
Impedance| 16 ohms
Transducer Low| 3.5” Woofer , 1.0” (25.4mm) Voice Coil
Rotation| 360 Degree Mechanical Adjustment
Enclosure Construction| Aluminium Cabinet, Metal Grille, Resistant Paint
Connector| 2 Pin smart connection
Dimensions(WxHxD)| φ112.5 x 583.2mm(φ4.43” x 22.96”)
Net Weight| 5.15Kg (11.35 Ibs)

Quick Start

When mounting a speaker onto any stand, always ensure that the stand is on a flat, level sur-face, with the legs fully extended. Be sure to check that the maximum load weight for the stands is greater than the weight of the ARRAY SYSTEMS loudspeaker. Never use a stand with a maximum load weight lower than the speaker.

Do not attempt to mout more than one speaker on a stand at one time.

The ARRAY SYSTEMS loudspeakers are heavy. It is recommended that a second person to help place the cabinet on a stand.

When the speaker is placed on a stand, always check the integrity and center of gravity of the system If the speaker can be tipped easily, or the pole is swaying, it is recommended that you lower the height of the stand. Position the stand and route cables so that the performers and the audience cannot tip over or trip on the system.

Connect Manner

AX V42.12

1. Insert the 4 PCS of fixed legs of AX POLE into the fixed seat of SUB, It means the assembly and connection of signal cable completed, details as below picture#1.
2. Snap the slot-terminal holder of AX V42BM into the upper protruding holder of AX POLE, and then push AX V42BM into slots along the opposite direction of grill. It means the assembly and connection of signal cable completed. details as below picture #2.
3. Snap the slot-terminal holder of AX V42TP into the upper protruding holder of AX V42BM, and then push AX V42BM into slots along the opposite direction of grill. It means the assembly and connection of signal cable completed . details as below picture #3.
4. Once assembly completed, no extra signal cable needed, based on the needs, user can rotate AX V42BM/AX V42TP towards left or right within 90 degree limit.

Technical Specifications

AXV42.12 SYSTEM: AXV12SA+AXV POLE+AXV42BM+AXV42TP

AXV42.12 System

Frequency Response| 42Hz – 20KHz (-10dB)
Total Amplifier Power| 700 W Continuous / 1400W Program / 2800W Peak Class D @ 4 Ohms
Maximum SPL@1M| 125dB
Crossover Frequency| 250Hz
Dispersion(-6dB)| 100°Horizontal
Dimensions(WxHxD)| 385 x 1970 x 500mm (15.15” x 77.56” x 19.69”)
Net Weight| 31.06Kg (68.47 Ibs)
AXV12SA|
System Type| 12″ Active Subwoofer Speaker Cabinet
Frequency Response(-6dB)| 40 Hz – 250 Hz
Total Amplifier Power| 700 W Continuous / 1400W Program / 2800W Peak Class D @ 4 Ohms
Amplifier, Subwoofer| 350 W Continuous / 700W Program / 1400W Peak Class D @ 4 Ohms
Amplifier, Satellite| 350 W Continuous / 700W Program / 1400W Peak Class D @ 4 Ohms
DSP Presets Modes| Center / Open / User
Electronic Protections| Over heat Protection/Short Circuit Protection/Digital Compressor
Cooling| Temperature-controlled fan
Connections| Input: 2 Combo-XLR&1/4”, RCA In L&R, 1 XLR Thru&Mixout
External Controls| Volume Control/Switch for Input sens/Swtich for mode selector/Power ON with GreenLED/Limiter with Red LED/Ground Lift/IP Control/MP3 and BT
Power Supply| 115V/230V ~50/60Hz Switchable
Enclosure Construction| Plywood Cabinet,Resistant Black Paint, Metal Grille with Foam, Rubber Feet, Integrated side handles
Mounting| Holder with Input Jacks for Pole
Dimensions(WxHxD)| 385 x 473 x 500mm (15.15” x 18.62” x 19.69”)
Net Weight| 21.5Kg (47.40 Ibs)
AXV Pole
Enclosure Construction| Plywood Cabinet, Resistant Paint, Metal Grille with Foam
Connector| 2 x Electronic Adapter – 1 x Input Connector for Sub & Another with Input Connector for Satellite
Dimensions(WxHxD)| 98 x 700 x 106.6mm(3.86” x 27.56” x 4.20”)
Net Weight| 2.70Kg (5.95 Ibs)
AXV42BM
System Type| 3.5″ Passive Speaker System
Output Power| 120W Continuous, 240W Program, 480W Peak
Sensitivity (1W/1M)| 95dB
Frequency Response(-6dB)| 160Hz-20kHz
Impedance| 8 ohms
Transducer Low| 4 x 3.5” Ferrite Woofer, 1.0” (25.4mm) Voice Coil
Rotation| 180 degree Mechanical Adjustment
Enclosure Construction| Plywood Cabinet, Resistant Paint, Metal Grille with Foam
Connector| 2 x Electronic Adapter – 1 x Input Connector for AXV Pole & Another with Input Connector for AXV42TP
Dimensions(WxHxD)| 98 x 448 x 106.6mm(3.86” x 17.64” x 4.20”)
Net Weight| 3.48Kg (7.67 Ibs)
AXV42TP
System Type| 3.5″ Passive Speaker System
Output Power| 120W Continuous, 240W Program, 480W Peak
Sensitivity (1W/1M)| 95dB
Frequency Response(-6dB)| 160Hz-20kHz
Impedance| 8 ohms
Transducer Low| 4 x 3.5” Ferrite Woofer , 1.0” (25.4mm) Voice Coil
Rotation| 180 degree Mechanical Adjustment
Enclosure Construction| Plywood Cabinet, Resistant Paint, Metal Grille with Foam
Connector| 1 x Electronic Adapter – 1 x Input Connector for AX V42BM or AX Pole
Dimensions(WxHxD)| 98 x 422 x 106.6mm(3.86” x 16.61” x 4.20”)
Net Weight| 3.41Kg (7.52 Ibs)

Wire Connections

For Active Speaker Cabinets

As to these circumstances, audio connections is mostly intended for the signal flow, so, determine the wire configuration according to your real application system and its connecting facility. Normally, you have the following choices:

• Balanced

• Unbalanced

For Passive Speaker Cabinets

Please only use the power connectors to make connections with other signal source equipment for the passive speaker cabinets. The power connector has four terminals: 1+, 1, 2+, 2.

In our cabinets, only 1+/1- are used to connect the Speaker+/Speaker-, and 2+/2- are not used.

Connect Manner

AX V62.15

1. Place the SUB on a flat surface.
2. Push the POLE from front to back into the SUB connector until it is tight-#1
3. Push the SAT-BM from front to back into the POLE connector until it is tight.-#2
4. Push the SAT-TP from front to back into the SAT-BM connector until it is tight.-#3
5. After the installation is completed, if you need to disassemble, press the “LOCK” button of the SUB connector and push the SAT forward slowly.

AXV24.215

1. Place the AXV24.215 SUB on a flat surface.
2. Push the AXV24.215 SAT from front to back into the SUB connector until it is tight.
3. After the installation is completed, if you need to disassemble, press the “LOCK” button of the SUB connector and push the SAT forward slowly.

Connection Plate System

Make your initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely down.

Two Active Subwoofers & Two Passive Satellite Speakers

1. Connect one side of the signal cable to the output of your mixer (left / right) with a TRS or
   XLR connector and the other side of the cable to the line input (combo) in the activesubwoofer (with a TRS to XLR connector). Then connect the speakon cable from the output of power in the Subwoofer to the satellites input.

2. Complete other connections as illustrated.

3. Turn on your mixer first, then the stereo power amplifier.

4. Turn up the volume controls of your amplifier to about70%.

5. Use PFL function to get the proper input level for the mixer, and adjust the Mian Mix Level control to manipulate the output level.

6. After using, turn off your stereo power amplifier first, then the mixer.

Make your initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely down.

1. Connect one side of the signal cable at your audio mixer into output left / right (with Stereo-Jack or XLR) and the other side of the cable into the line input (Stereo-Jack) of your active speaker cabinet.
2. Connect the power cord to mains.
3. Turn on your mixer first, then the active speaker cabinets.
4. Turn up the volume control of the active speaker cabinets.
5. Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the output level.
6. After using, turn off your stereo power amplifier first, then the mixer.

Back Panel Description

AX V 42.12

1. AC POWER SOCKET WITH MAIN FUSE.

2. ON-OFF MAIN POWER SWITCH.

3. MAIN FUSE

4. CONVECTION FAN

5. IP CONTROL

6. THRU OUTPUT ON XLR CONNECTOR
   This is a male XLR-type connector that produces exactly the same signal that is connected to the main input jack or a mix of input1 and input2.

7. CENTER / OPEN / USER CENTER: Allow use this subwoofer with the 2 satellite(AX V42TP and AX V42BM). Defaults factory preset
   for Both satellites never rotate and keep grill towards front
   OPEAN: Allow use this subwoofer with the 2 satellite(AX V42TP and AX V42BM). Defaults factory preset for the AX V42TP (or AX V42BM)turn 45 degree towards left, another turn 45 degree towards right.

8. POWER. GREEN LED, INDICATE ON STATUS.

9. SIGNAL / LIMIT, RED LED, INDICATE ON STATUS.

10. INPUT2 ON COMBO CONNECTOR.

11. LINE / MIC SWITCH(CHANNEL INPUT1 ONLY)

12. LINE / MIC INPUT1 ON COMBO CONNECTOR.

13. XLR AND 1/4” COMBO INPUT2 INPUT2 may accept Hi-Z sources (such as guitars) via the TRS 1/4” input, or line-level signal via XLR. NEVER connect the output of an amplifier directly to the input of the loudspeaker. This could damage the input circuitry of the active loudspeaker.

14. XLR AND 1/4” COMBO INPUT1
    INPUT1 may accept a MIC or line-level signal via XLR or line-level signal via TRS 1/4” cable. Be aware of the position of the MIC / line switch (12).

15. RCA INPUTS (INPUT2 ONLY).

16. INPUT1 / MIX SWITCH (THRU OUTPUT)
    This switch allows you to choose whether only the input1 signal is sent out to the next loudspeaker(switch out-input1) or mix of the input1 and input2 signals are sent out to the next loudspeaker(switch in-Mix).

**AX V62.1

**

1. AC INPUT-The AC connection is established via the IEC connector. The IEC connector is compatible with a lockout power cord (not included).
2. POWER – AC switch for turning the power on or off. When POWER is turned on,the power led lights up and LCD screen lights up.
3. MP3/BT PLAYER for option.
4. Convection fan.
5. OUTPUT – The XLR output sends mixed input signals to other speakers or subwoofers, Input level controls the level of signal sent to the OUTPUT, The MASTER VOL or DSP control settings do not affect the OUTPUT.
6. INPUT1 / INPUT2 – FOR line\ MIC or HI-Z input level control is available for INPUT 1/2
7. INPUT3/4 – FOR line stereo input level control is available for INPUT 3/4
8. RCA INPUTS- FOR line stereo input level control is available for INPUT 3/4
9. VOLUME- Input level is used to adjust the level control of the level of a signal input.
10. AUX IN – Line input level control is available for stereo
11. SIG / LIMITER signal light, it will light green when there is signal, and the red light will start to ligh when the amplifier starts to compress.
12. LCD – DSP Control and monitoring interface
13. MASTER VOL – Total volume adjustment ,range: -60dB ~ +10dB. DSP-Scroll through the menus and select the available options. Press the MASTER VOL knob to enter the DSP menu item.
14. IP CONTROL
15. POWER indicators – the POWER LED will lihg up when turn on.
16. PROTECTION indicators – the PROTECTION LED will lihg up when an exception occurred in DSP
17. LIMITER indicators – the LIMITER LED will lihg up when the amplifier starts to compress

**AXV24.215

**

1. AC INPUT-The AC connection is established via the IEC connector. The IEC connector is compatible with a lockout power cord (not included).
2. POWER – AC switch for turning the power on or off. When POWER is turned on,the power led lights up and LCD screen lights up.
3. MP3/BT PLAYER for option.
4. Convection fan.
5. OUTPUT – The XLR output sends mixed input signals to other speakers or subwoofers, Input level controls the level of signal sent to the OUTPUT, The MASTER VOL or DSP control settings do not affect the OUTPUT.
6. INPUT1 / INPUT2 – FOR line\ MIC or HI-Z input level control is available for INPUT 1/2
7. INPUT3/4 – FOR line stereo input level control is available for INPUT 3/4
8. RCA INPUTS- FOR line stereo input level control is available for INPUT 3/4
9. VOLUME- Input level is used to adjust the level control of the level of a signal input.
10. AUX IN – Line input level control is available for stereo
11. SIG / LIMITER signal light, it will light green when there is signal, and the red light will start to ligh when the amplifier starts to compress.
12. LCD – DSP Control and monitoring interface
13. MASTER VOL – Total volume adjustment ,range: -60dB ~ +10dB. DSP-Scroll through the menus and select the available options. Press the MASTER VOL knob to enter the DSP menu item.
14. IP CONTROL
15. POWER indicators – the POWER LED will lihg up when turn on.
16. PROTECTION indicators – the PROTECTION LED will lihg up when an exception occurred in DSP
17. LIMITER indicators – the LIMITER LED will lihg up when the amplifier starts to compress

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>