NORTEK R104HD Replacement Burner Igniter Inshot Installation Guide
- June 15, 2024
- NORTEK
Table of Contents
R104HD Replacement Burner Igniter Inshot
Installation Guide
R104HD Replacement Burner Igniter Inshot
LARGE PACKAGE INSHOT BURNER IGNITER
REPLACEMENT – R8GD, R8GE, R104GD,
R8HE AND R104HD UNITS
INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
INSTALLER: Please read all instructions before servicing this equipment. Pay
attention to all safety warnings and any other special NOTES highlighted in
the document. Safety markings are used frequently throughout this document to
designate a degree or level of seriousness and should not be ignored.
WARNING indicates a potentially hazardous situation that if not avoided,
could result in personal injury or death. CAUTION indicates a potentially
hazardous situation that if not avoided, may result in minor or moderate
injury or property damage.
WARNING:
ELECTRICAL SHOCK, FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury or
property damage.
Improper servicing could result in dangerous operation, serious injury, death
or property damage.
- Before servicing, disconnect all electrical power to the unit.
- When servicing controls, label all wires prior to disconnecting. Reconnect wires correctly.
- Verify proper operation after servicing.
WARNING:
Unless noted otherwise in these instructions, only factory authorized parts or
accessory kits may be used with this product. Improper installation, service,
adjustment or maintenance may cause explosion, fire, electrical shock or other
hazardous conditions which may result in personal injury or property damage.
WARNING:
Use caution when removing components or handling this product. Personal
injury can occur from sharp metal edges present in all sheet metal constructed
equipment.
GENERAL INFORMATION
This kit replaces Nortek 632320 igniter which is in Nortek kit 903179. The
igniter included in this kit is a different design but is an equal alternate.
This kit includes (1) igniter, (1) universal igniter bracket, (1) wire tie and
(3) fasteners. The 2 pin Molex plug is pre-installed to the new igniter for
an easier installation.
First, disconnect all electrical power to the unit. Remove the control panel
to gain access to the burner assembly and the igniter. Establish which style
of igniter bracket is on your equipment. There are 2 styles of igniter
brackets. If your equipment has the bracket in Figure 1, refer to the
instructions in Section 1. If your equipment has the bracket in Figure 2,
refer to the instructions in Section 2.
Section 1. Models – R8GE, R8GD, R104GD
- Disconnect the Molex plug, remove the 2 screws holding the old igniter in place and remove the assembly. These parts and screws will not be used with the new igniter.
- Insert new bracket in the burner box opening but do not fasten. See Figure 3.
- Insert the new igniter in the igniter bracket but do not fasten yet with the screws.
- Using (2) of the screw provided, fasten the bracket to the burner box.
- Using (1) screw, fasten the igniter to the bracket and re-attach the Molex plug.
- Use the wire tie to make sure the igniter wires are not touching any metal.
- The finished assembly should look like Figure 4, the igniter parallel to the burner face.
- Re-establish power, verify ignition and normal operation. Refer to the installation instructions for details.
- Replace the panel after a successful ignition.
Section 2. Models – R8HE, R104HD
- Disconnect the Molex plug, remove the 2 screws holding the old igniter in place and remove the assembly. These parts and screws will not be used with the new igniter.
- Fasten the igniter bracket with the (2) provided screws. See Figure 5.
- Insert the new igniter in the igniter bracket, fasten with the (1) provided screw and re-attach the Molex plug.
- Use the wire tie to make sure the igniter wires are not touching any metal.
- The assembly should look like Figure 6, the igniter parallel to the burner face.
- Re-establish power, verify ignition and normal operation. Refer to the installation instructions for details.
- Replace the panel after a successful ignition.
10465290 (NEW)
Specifications & illustrations subject to change without
notice or incurring obligations (08/23).
O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>