BBSHD TCB 22TCB 001B 8.5 Inch Electric Scooter User Manual
- June 15, 2024
- BBSHD
Table of Contents
BBSHD TCB 22TCB 001B 8.5 Inch Electric Scooter
Package Contents
- Assembled
- Electronic
- Scooter
Accessories
-
Charger plug in
-
Screw*4
-
Hexagon Wrench
-
Cross Wrench
-
Power cord
Carefully check the package contents before starting to ensure that everything is included
Product Review
The power level is indicated by four power lights on the control panel. As power is consumed, the lights will change from solid to flashing, and finally turn of from up to down. When all four power lights are on, the battery level is between 100%-86%; When The Lights are solid and one is flashing, the battery level is between 85%-71%,and so on. When the bottom power light flashes, it indicates low power. Please recharge soon for further use. After running out of power, all lights will turn off, and the scooter will coast until it comes to a complete stop.
The bottom light either flashes white or green. The white light indicates regular mode, and green light indicates power-saving mode.(power-saving mode: max speed of 11.2 mph with smoother acceleration for beginners)
When the scooter is off, press the button to turn on the scooter; When the scooter is on, press and hold for 2 seconds to turn off the scooter. After turning on, press the button to turn on or off the headlight; And press twice to switch between modes.
Assembly And Setup
-
Fasten the handlebar stem on the headset, and put the kickstand down
-
Attach the handlebar to the stem
-
Tighten the screws onto both sides of the stem with the hexagon wrench.
-
After the assembly, press the power button to check if it’s working properly.
Charge Your Scooter
-
Lift up the rubber flap
-
Plug the power adapter into the charging port.
-
When Charging Is completed, put back the rubber flap.
How To Ride
-
Wear helmets and knee pads in case of falls and injuries when you learn to ride the scooter.
-
Turn on the scooter, and check the power indicator.
-
Step on the deck with one foot, and slowly kicks off the other on the ground.
-
When the scooter starts to coast, put both feet on the deck and press the accelerator (the accelerator initiates once the coasting speed exceeds 3.1 mph)
-
Release the accelerator and the kinetic energy recovery system (KERS) initiates automatically to brake slowly; And squeeze the brake lever for a sudden brake.
-
Tilt your body to the steering direction as you turn, and slowly turn the handlebar.
Safety Instructions
Watch out for safety risks
Do not ride in the rain.
Keep your speed between 3.1-6.2 mph when you ride through speed bumps, elevator door sills, bumpy roads or other uneven surfaces. Slightly bend your knee to better adjust mentioned surfaces.
Look out for doors, elevators and other overhead obstacles.
Do not accelerate when you go downhill.
Do not press the accelerator when you’re walking alongside the scooter.
Always steer clear of obstacles.
Do not hang bags or other heavy stuff on the handlebar.
Keep both feet on the deck all time.
Do not ride in traffic lanes or residential areas where vehicles and pedestrians are both allowed.
Do not turn the handlebar violently during high-speed riding.
Do not ride in a ponding that is higher than 0.78 inches .
Do not ride with anyone else, including children.
Do not keep your feet on the rear mudguard.
Do not touch the disc brake.
Do not keep your hands away from handlebar.
Do not try riding up or down stairs, and jumping over obstacles.
Safety Reminder
- This electric scooter is a leisure device. But once they’re in a public area, they’ll be seen as vehicles, subjecting to any risks faced by vehicles. For your safety, please follow instructions in the manual and traffic laws and regulations set forth by government and regulatory agencies.
- At the same time, you should understand that risks cannot be entirely avoided as others may violate traffic regulations and drive incautiously, and you’re exposed to road accidents just as when you’re walking or biking. The faster the scooter is, the longer it takes to stop. On a smooth surface, the scooter may slip, lose balance, and even result in a fall. Thus it is crucial that you use caution, keep proper speed and distance, especially so when you’re unfamiliar with the place.
- Respect pedestrians’ Right of Way. Try not to startle them while driving, especially children. When you ride from behind pedestrians, ring your bell to give them a heads-up and slow your scooter to pass from their left (applicable to countries where vehicles drive on the right).When you ride across pedestrians, keep to the right at a low speed. When you drive across pedestrians, keep the lowest speed or getting off the vehicle.
- Closely follow the safety instructions in the manual especially in China and countries that lack relevant laws and regulations regarding electric scooters. Xiaomi Communication Co., Ltd. shall not be liable for any financial losses, physical injuries, accidents, legal disputes and other interest conflicts resulted from actions that violate user instructions.
- Do not lend your scooter to whoever knows not the operations. And when you do lend it to your friends, please take the responsibility to ensure he/she knows the operation and wears the safety gear.
- Check the scooter before every use. When you note loosen parts, low battery alerts, flat tires, excessive wear, strange sounds, malfunctions and other abnormal conditions, stop riding immediately and call for professional support.
WARNING-Risk of Fire-Do Not Service the scooter yourself.
Folding and Carrying
Make sure that the scooter’s turned off. To fold, unlock the folding mechanism, and bend the handlebar stem to hook the buckle on the rear mudguard. To open, press the bell trigger to remove from the buckle, erect the handlebar and lock the folding structure.
Hold the handlebar stem with either one hand or both hands to carry
Maintenance and Care
Cleaning and storage If you see stains on the scooter’s body, wipe them off with a damp cloth. If the stains won’t scrub off, put on some toothpaste, and brush them with a toothbrush, then wipe them off with a damp cloth. If you see scratches on plastic parts, use sandpaper or other abrasive materials to polish them.
Notes: do not clean the scooter with alcohol, gasoline, kerosene or other corrosive and volatile chemical solvents to prevent dire damage. Do not wash the scooter with a high-pressure water spray. During cleaning, make sure that the scooter’s turned off, the charging cable is unplugged, and the rubber flap is closed as water leakage may result in electric shock or other major problems. When the scooter’s not in use, keep it indoors where it is dry and cool. Do not put it outdoors for long time. Excessive sunlight, overheating and overcooling accelerate tire aging and compromise the scooter and the battery pack’s lifespan.
Battery maintenance 1. Use original battery packs, use of other models or brands may bring about safety issues; 2.Do not touch the contacts. Do not dismantle or puncture the casing. Keep the contacts away from metal objects to prevent short circuit which may result in battery damage or even injuries and deaths; 3.Use original power adapter to avoid potential damage or fire;4. Mishandling of used batteries may do tremendous harm to the environment. To protect natural environment, please follow local regulations to properly dispose used batteries.5.After every use, fully charge the battery to prolong its lifespan.
Do not place the battery in an environment where the ambient temperature is higher than 122°F or 1 over than-4°F(e.g., do not leave the scooter or the battery pack in a car under direct sunlight for an extended time). Do not throw the battery pack into fire as it may lead to battery failure, battery overheating, and even another fire. If the scooter is expected to be left idle for more than 30 days, please fully charge the battery and place it in a dry and cool place. Keep in mind to recharge it every 60 days to protect the battery from potential damage which is beyond limited warranty.
Always charge before exhausting the battery to prolong the battery’s lifespan. The battery pack performs better at normal temperature, and poor when it is below 32°F. For instance, when it is below -4°F, the riding range is only half or less at normal state. When the temperature rises, the riding range restores. For detailed information, please refer to Mi Home App.
Note : fully charged Mi Electric Scooter will last for 120- 180 days. The built-in intelligent chip will keep a log of its charging and discharging records. The damage caused by prolonged no charge is irreversible and is beyond limited warranty. Once the damage is done, the battery can not be recharged (non-professionals are forbidden to dismantle the battery pack, as it may cause electric shock, short circuit or even major safety accidents).
Adjusting the disc brake
If the brake is too tight, use the M4 hexagon wrench to loosen the screws on the caliper, slightly send back the brake cable to shorten the length, then tighten the screws. If the brake is too loose, loosen the screws. slightly pull out the brake cable to lengthen it.
Adjust the handlebar
If the handlebar and its stem sway during riding, use the M5 hexagon wrench to tighten the screws on the folding mechanism.
How to use the extended nozzle adapter
Remove the outer and inner tires
Note: Crowbars not included, and should be purchased separately.
- Deflate the inner tire first. Use a tool to press the core rod in the air valve so that air is discharged from the inner tire, and use another hand to forcibly pinch the tire at different places to discharge more air.
- Select a position far from the air valve on the outer tire, use two crowbars to prize up the outer tire by about 1/6 of the circumference, and forcibly separate one side of the outer tire from the hub.
- Find the air valve, and pull the air valve out of the air valve hole of hub. To pull out the air valve more conveniently, hold the air valve of the inner tire, and pull the outer tire outwards slowly, lest the inner tire would be damaged. Remove the inner tire from the position of air valve in sequence, and separate the inner tire finally.
Note: Wrap the pointed end of the crowbar with fiber cloth so that it will not damage the inner tire and coating of the hub.
Install the inner and outer tires
- Fill a small amount of air into the deflated inner tire till the inner tire is just bulged to look round.
- Put the hub on the top of a desk. Pay attention to the direction when installing the outer tire. There is an arrow on the outer tire, and it must be consistent with the forward direction of the wheel. Use one hand to hold the hub, and use the other hand to insert one side of the outer tire in the hub groove.
- Insert the air valve of the inner tire into the air valve hole. Insert the inner tire in the outer tire clockwise and in sequence. Make sure that the air valve does not tilt. Then, insert the other side of the outer tire in the hub groove. Finally use a crowbar to install the remaining tire lips in the hub groove. After installation, pinch the outer tire to check if the inner tire is pressed by the tire lips of outer tire.
- Inflate the inner tire to 15-20 PSI, and check the safety lines at two sides of the outer tire. Make sure that the distances from the safety lines to the hub edge are consistent.
- Finally inflate the inner tire to 45-50 PSI. Tighten the air valve cap. Then, the tire assembly is completed. Note: Wrap the pointed end of the crowbar with fiber cloth so that it will not damage the inner tire and coating of the hub.
Specifications
| Product Name | Electric scooter |
|---|---|
| Max Load Weight | 100KG |
| IP grade | IP54 |
| Brake Type | Electronic brake and Disc brake |
| Cruising Range | 30-40KM (It is the experimental data under ideal |
conditions, such as a 60KG rider riding on flat road in summer without wind)
Max Speed| 25KM/H (Speed ECO mode:10KM/H; D:15KM/H; S:25KM/H)
30KM/H (Speed ECO mode:10KM/H;D:15KM/H; S:30KM/H)
Maximum Climbing Angle| 15-20Degree
Tires| 8.5 Inch Solid tire ▢ Inflatable tire ▢ Honeycomb tire
✔
Rated Voltage| 127-220VAC 50/60Hz
Motor Power| Brushless motor/ 350W R
Battery| 36V,4.4AH ▢ 6.6AH ▢ 7.5AH 10.4AH R ✔
Charging Time| 4-6Hours
Product Weight| 14.5KG
Packing List|
- Electric scooter*1,
- User manual*1,
- Charging adapter*1,
- Screw*4,
- Hexagon wrench*1,
- Cross wrench*
Warranty
-
Warranty service is carried out in accordance with the law on 《 consumer rights》 and the 《Law on the quality of products 》The warranty service includes Recommendation: use the packaging for safe transport of the device. We recommend keeping the original packaging within 15 days after receipt of goods.
-
Warranty terms
Part Name| Warranty Period| Exception| Note
---|---|---|---
Li-ion battery
Charger| Three months
One month| -
Damage due to long-term power lack.
-
Water log | Replacement out of the warranty period will be charged at cost price
Controller| One month| -
Water log
-
Damage by strong deliberate impact | Replacement out of the warranty period will be charged at cost price
Motor| One year| -
Water log
-
Damage by strong deliberate impact | Replacement out of the warranty period will be charged at cost price
Frame, brake cables, Brake pads, Paints| Quick-wear parts are not covered by warranty| Replacement of parts that are not covered by warranty will be charged at cost price
LED lights ,Grips Rubber foot rest, electronic brake plastic part, tyres, Inner tubes, and other quick-wear parts.
Caution:
Hex wrench, cross wrench and other consumable component parts have no
warranty.
- Non – warranty regulations
- Authorized maintenance, misuse, collision, negligence, abuse, intake, accident. Improper use of non-product accessories, or tear up the modified label, anti-counterfeit mark.
- The warranty period has expired;
- Damage, caused by force majeure;
- Failures, that have arisen in connection with the human factors (including, but not limited to, excessive wetting device, puncture, drop, scratch and damage an outer casing, which have arisen as a result of normal use of goods)
- If this product is used for commercial purposes, all warranty conditions are not maintained.