DECO BREEZE 56 Brown Decorative Floor Fan Instruction Manual

Floor Fan Instruction Manual
DECO BREEZE
DECORATIVE
FLOOR FAN

ATTACH YOUR RECEIPT HERE

SerialNumber __ Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer service department
READ INSTRUCTIONS CAREFULLY PRIOR TO ASSEMBLY AND SAVE THESE INSTRUCTIONS.

PACKAGE CONTENTS

SAFETY INFORMATION

READ AND SAVE THESE. Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service

• Use the fan only for the specific purpose outlined in this instruction manual.
• Do not operate fan until fully assembled.
• Ensure the correct voltage is being used prior to plugging in your fan (120V AC Electrical Outlet).
• Unplug fan from outlet when not in use, when changing locations, before assembly or disassem- bly, or prior to cleaning.
• Avoid contact with all moving parts. Never insert your fingers, pencils or other objects through the fan grill during operation.
• Place the fan on a stable and level surface to avoid tipping or being knocked over accidentally.
• Do not operate the fan directly adjacent to curtains, plants, window coverings, etc. to avoid acci- dental entanglement.
• While your fan is tolerant of exposure to most weather situations, it is recommended you bring the fan unit into a covered or indoor location during periods of extreme cold, snow or rain.
• Do not submerge your fan under water and keep a safe distance from pools or outside water features or irrigation sprinklers.
• Do not use an outdoor watering hose or pressure sprayer to clean your fan. Please see the CARE AND MAINTENANCE section for specific instructions on cleaning.
• To avoid potential fire hazards, never place your fan or its electrical cord under rugs, or carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
• Place the electrical cord away from busy areas to avoid accidental tripping and contact.
• Always insert or remove plug from the outlet by grabbing the plug by hand. Do not pull on the electrical cord.
• Never operate the fan near an open flame or in the presence of explosive or combustible gases or fumes.
• Should the fan (including the electrical cord) ever become damaged or a malfunction occurs, discontinue operation at once until a certified repair has been made.
• Keep the fan out of the reach of children and pets. + Do not expose infants or seniors to prolonged periods of direct cold air.
• Never attempt to disassemble or alter the product in any way not instructed by this manual
• WARNING – To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device.
• Use only on GFCI protected receptacles.

DANGER
ELECTRICAL SHOCK HAZARD.
Do not plug cord into outlet with wet hands. Follow manual for recommended usage.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 10-15 minutes
Tools Required for Assembly (not included): Phillips Screwdriver

ASSEMBLY INSTRUCTIONS

1. For the floor bases, the base comes in multiple parts for shipping convenience. To assemble, simply thread the pieces together at their adjoining points. Using a Phillips screwdriver, remove locking screw (N) from fan motor assembly (J). Insert electrical cord (P) into connection pole (Q) and pull through the bottom exit hole of fan base (O).
2. Slide fan motor assembly (J) onto upper pole, aligning screw holes of both. Re-insert and tighten locking screw (N).
3. Remove Black Grill Locker (D) from Motor Assembly (J).
4. Slide on Back Girill (E) on to front of Motor Assembly (E) with the handle at the top center. Attach Black Grill Locker (D) and rotate lockwise to tighten.
5. Remove 5×8 Screw (G) from the Fan Blade (C) hozel piece. Slide Fan Blade (C) on to Motor Shaft (I) and re-insert 5×8 Screw (G) and tighten firmly.
6. Open all grill clasps on Front Grill (A). Remove Safety Screw (F) from bottom of Front Grill (A) and place aside momentarily. Position Grill Clip (B) at the top center of Back Grill (E) and hook over frame to secure. Secure all grill clasps so both grill frames are pressed together inside each clasp. Re-attach Safety Screw (F) and secure.

OPERATION INSTRUCTIONS

• The speed control knob (L) is located on the top rear of fan motor assembly (J). Position 0 = off, position | = low speed, position Il = medium speed and position 11 = high speed. Simply twist switch to desired position to operate.
• The fan can operate in stationary or oscillation mode. The oscillation knob (K) is located on the top rear of fan motor assembly (J). To engage the oscillation function simply depress the button. To stop, pull up.
• The fan head can also tilt slightly for added adjustment. Loosen tilt adjustment knob (M) and pitch the fan head to the desired angle and then retighten.

TROUBLESHOOTING

If you have any questions regarding the product, please call customer service Do not attempt to repair or modify any mechanical or electrical parts of this fan. Doing so may void the warranty.

position.
Confirm the plug connectors are perfectly joined.
The fan will not oscillate.| Push down on knob on top of motor housing to activate oscillation.

CARE AND MAINTENANCE

• Always unplug the appliance from the power supply before servicing.
• Clean parts with a duster, soft cloth or compressed air cannister (similar to computer cleaners). Warning: Do not use cleaning solutions or abrasive material as it may damage the finish or components of the fan.

USER SERVICING INSTRUCTIONS
This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.

1. Grasp plug and remove from the receptacle or on other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover. Using a flathead screwdriver tip, slide open fuse access cover on top of attachment plug towards the prongs.
3. Remove fuse carefully. Gently press on the end of the fuse with the flat head screwdriver tip and pull upward to remove. Risk of fire. Replace fuse only with 5-amp, 125-volt fuse.
4. Close fuse cover. Slide closed the fuse access cover on top of the plug and plug back into the outlet.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>