GOBOOST 18P.5.LLCPA.1 Mobile Signal Repeater User Manual
- June 15, 2024
- GOBOOST
Table of Contents
<<< User Manual
Mobile signal repeater
Product parameters
model
18P.5.LLCPA.1
Network
LTE-B12, LTE-B13, CDMA, PCS, AWS
parameter
| Frequency Range | Frequency | Uplink | Downlink |
|---|---|---|---|
| LTE-B12 | 699~716 | 729~746 | |
| LTE-B13 | 777~787 | 746~756 | |
| CDMA | 824~849 | 869~894 | |
| PCS | 1850~1910 | 1930~1990 | |
| AWS | 1710~1755 | 2110~2155 | |
| Output Power | 16±2 dBm | 16±2 dBm | |
| Gain | 58±3 dB | 63±3 dB | |
| Bandwidth | 17M+10M+25M+60M+45M | ||
| --- | --- | ||
| Ripple in Band | LTEB 12/17≤6dB;LTE-B13≤6dB;CDMA≤6dB;PCS ≤6dB;AWS≤6dB | ||
| Spurious Emission | 9KHz~1GHz | ≤ -36 dBm | |
| 1GHz~12.75GHz | ≤ -30 dBm | ||
| Intermodulation Products | 9KHz~1GHz | ≤ -36 dBm | |
| 1GHz~12.75GHz | ≤ -30 dBm | ||
| VSWR | ≤3 | ||
| MTBF | ＞50000 hours | ||
| Power Supply | AC：100~240V, 50/ 60Hz；DC：5V 3A | ||
| Power Consumption | < 6W | ||
| Impedance | 50 ohm |
Mechanical Specification
| RF Connector | N-Female N |
|---|---|
| Dimensions (DWH ) | 25316028mm |
| Packing size (DWH ) | 33522050mm |
| Net weight | <0.53KG |
| Gross weight | <0.87KG |
| Installation Type | Wall Installation |
| Environment Conditions | IP40 |
| Humidity | < 90% |
| Operating Temperature | -10℃ ~ 55℃ |
Product display
-
FREQUENCY LIGHT
-
POWER LIGHT
-
Output gain
-
Power Supply
-
Indoor port
Installation steps
Step 1: Install the outdoor antenna on the roof or other positions where you can receive 4 bars of signal or more
Step 2: Connect the outdoor antenna to the BTS port via the cable and tighten the connectors at both ends, make the outdoor antenna point to the base station
Step 3: Connect the indoor antenna to the MS port, and place the indoor antenna at a higher position so as to increase signal coverage
Step 4: After connecting and tightening the two antennas, plug in the power supply and check the condition of the signal display light
Step 5: Check whether the phone signal has been improved or not. If it is not ideal, you can adjust the height or direction of the outdoor antenna. A good outdoor signal is half of the success.
Attention: There must be a solid wall between the indoor antenna and the outdoor antenna to prevent self oscillation.
installation drawing
- base station
- host
- Indoor antenna
Application Scenario
| |
---|---|---
villa| basement| residence
| |
hotel| Office building| BarKTV
frequently asked question
After the installation, the signal improvement is not significant, and the indoor coverage area is small
1. Adjust the position and direction of the outdoor antenna
2. Check if the cable is properly connected
3. Raise the outdoor antenna so that it can receive better signals
4. Replace high-power amplifier
5. Replace a high gain outdoor antenna
The phone signal is full, but the call quality is poor
The distance between outdoor and indoor antennas are too close, so it is necessary to increase the distance between them, or increase barrier isolation between them
After installation, the signal did not improve, but it was worse
The distance between outdoor and indoor antennas are too close, so it is necessary to increase the distance between them, or increase barrier isolation between them
I have been using it normally before, but suddenly the signal is not good after using it for a period of time
1. Check if water ingress at outdoor cable joints
2. Check if the power indicator light is normal
3. If there is no water ingress into the cable and the power indicator light
is normal, it is possible that the amplifier has malfunctioned and needs to be
returned to the factory for repair
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>