Leegoal BravoX Portable Blender Instruction Manual

Leegoal BravoX Portable Blender

Product Information

Specifications

• Model: Bravo
• Language: English
• Cup lid: Sports cup lid
• Hand ring: Yes
• Cup body: Included
• Blade: Included
• Digital display: Yes
• Switch button: Yes
• Charging interface: Included
• Bottom cover: Included
• Blade cover: Included
• Mainframe base: Included

Operation Instructions

Step 1: Assembly

1. Place the cup body on the mainframe base.
2. Attach the blade to the bottom of the cup body.
3. Securely close the bottom cover.
4. Place the cup lid on top of the cup body.
5. If available, attach the hand ring to the cup lid.

Step 2: Adding Ingredients

1. Make sure the blender is turned off.
2. Remove the cup lid.
3. Add your desired ingredients to the cup body.
4. Make sure not to exceed the maximum water level indicated on the cup body (500ml).
5. If necessary, add at least the minimum required amount of water (150ml) for proper blending.
6. Securely close the cup lid.

Step 3: Blending

1. Press and hold the ON/OFF button for 3 seconds to turn on the blender.
2. The digital display will show the current mode (juicing or pulsing) and the countdown time.
3. To start blending, press the PULSE button or the RUN button depending on the desired mode.
4. Wait for the blending process to complete.

Step 4: Cleaning

1. Make sure the blender is turned off and unplugged.
2. Remove the cup lid, cup body, and blade from the mainframe base.
3. Wash each component with warm soapy water.
4. Rinse thoroughly and allow them to air dry.

FAQ

Q: Why is the blender not blending and showing an ER message?

A: The usual reasons for this issue are that the gasket has not been put flat or it was misplaced. Please follow the troubleshooting steps below:

1. Pull out the gasket and assemble it again.
2. Make sure to keep the gasket flat and close to the bottom.
3. When installing the bottle, press and tighten it.

Q: How do I contact customer support?

A : For any questions about the use of the product, please contact us via Amazon or email us at vip@leegoal.com. We believe we can provide a satisfactory solution to any problem you encounter.

Warm Tips Dear Customer

Thanks for purchasing our “blender bravo” Here are some Special Tips for you

If you have the below problems:

1. The Blender is not blending and always shows an “ER” message
2. liquid leaking out of the bottom of the bottle The usual reasons are :
3. The gasket has not been put flat
4. The gasket was misplaced

Troubleshooting:

1. Pull out the gasket and assemble it again
2. MUST keep the gasket flat and close to the bottom
3. When you install the bottle please PRESS & TIGHTEN

Any questions about the use of the product please contact us via Amazon or vip@leegoal.com first before you request a return, We believe we can provide a satisfactory solution to any problem you encounter Best Wishes

In package

Components

1. Cup lid
2. Sports cup lid
3. Hand ring
4. Cup body
5. Blade
6. Digital display
7. Switch button
8. Charging interface
9. Bottom cover
10. Blade cover
11. Mainframe base

Operation diagram

Product models and specifications

Specifications

• Model: Bravo.
• Charging specification: DC 5 V/2 A
• Working current: Maximum 26 A
• Rated power: 300W (MAX)
• Battery specification: about 2000 mAh*3/12 V
• Charging time: 4~5 h
• Note: Using a power adapter with less than 5V/2A is not recommended
• Operating time in standard mode: 20 seconds
• Operating time in PULSE mode: 30 seconds
• Motor speed: up to 20000 revolutions/min ‡10%
• Cup body capacity: 600 ml
• Product size: 3.3 3.3 11.5 inch
• Product weight: <0.85kg

Electrical schematic

Function introduction

Explanation of digital tube icon

1. Power on and off:
   • Press and hold for 3 seconds to turn on, and the digital tube displays  Press and hold the button for 3 seconds to shut down in the power-on state. If no operation is detected in the power-on state, it will shut down automatically after standing for 1 minute.
2. Working mode:
   • In the power-on state, click the button to enter the Normal Working Mode. After the digital tube display decreases from 20 to 0, the blender stops working.
   • In the power-on state, double-click the button to enter the PULSE Juicing Mode (This is a jump signal juicing mode, which reaches the maximum speed instantly, and then rapidly changes the speed frequency. It is used to crush harder food, frozen fruits or ice cubes, etc., in this mode, it is more conducive to the extraction of food nutrition). After the digital tube display decreases from 30 to 0, the blender stops working.
3. Idling protection:
   • If you operate the blender without putting any food into it, the blade will only run for 6 seconds.
4. Pause function:
   • When working, click the button to pause juicing, the digital tube displays and the motor stops working. After the pause, click the button again to resume juicing, and the blender stops working after the digital tube display decreases from 20 to 0 again.
5. Cup lock switch:
   • If the bottle body is not installed correctly, press and hold for 3 seconds to turn it on, the digital tube displays and flashes 3 times, and the buzzer emits 3 warning sounds of di-di-di”. At this time, single-click or double-click will not work. After prompting 3 times, it will shut down automatically without any operation;
   • Warm tips:
   • Loosen the cup lid during work, the motor stops, the digital tube displays and flashes 3 times, and the buzzer emits 3 warning sounds of “di-di-di”. Then it will shut down automatically without any operation;
   • When the bottle body is correctly installed and the machine is turned off or on, the buzzer will emit a prompt sound of “di”, and the digital tube displays 88
6. NTC discharge temperature protection:
   • When the NTC probe detects that the temperature exceeds 65 degrees during discharging, the motor cannot be started. When the NTC probe detects that the temperature exceeds 65 degrees during operation, the motor stops immediately, the digital tube displays and flashes 3 times, the buzzer emits 3 warning sounds of “di-di-di”, › and then it will shut down automatically.
   • Warm tips:
   • After triggering NTC discharge protection, the blender enters the temperature protection mode. In this mode, the blender cannot be turned on by long pressing, the digital tube displays and flashes 3 times, the buzzer emits 3 warning sounds of “di-di-di”, and then it will shut down automatically. It can be turned on again after 10 minutes.
7. Low power protection:
   • When low battery power is detected during operation, the digital tube displays and flashes 3 times, the buzzer emits 3 warning sounds of “di-di-di”, and then it will shut down automatically.
   • Warm tips:
   • After low power is triggered, long press, single click, and double click again will not work. The digital tube displays and flashes 3 times, the buzzer emits 3 warning sounds of “di-di-di”, and then it will shut down automatically, and the charging will resume.
8. Stuck blades prevention:
   • When the machine is jammed during operation, the motor is turned off, the digital tube displays and flashes 5 times, the buzzer emits 5 warning sounds of “di di-di di” and then the digital tube displays
9. Charging:
   • The digital tube displays when charging, and the battery indicator light flashes.
   • After fully charged, the digital tube will display
   • NTC charging temperature protection:
   • When the NTC probe detects that the temperature is ≥45°C or lower than -10°C, the charging stops, the digital tube displays and flashes, and the buzzer emits a “di-di” warning sounds. When the temperature is lower than 45°C or higher than -10°C, the charging is resumed. (Temperature tolerance ‡2°C)

Fault resolution

1. When starting blender, it shows ‘Er’ and can’t start?
   • The cup body and the base are not in right place, please tighten the cup body till display ’88.
2. When start blender, it shows ‘Lo’, and can’t turn on?
   • The battery voltage is too low, please charge it in time.
3. Stop down in 6 seconds after starting?
   • Add more fruits and vegetables…. and attention to the level mark on body “Min” and “Max”.
4. When starting blender, “EL” flashes for 5 seconds?
   • Open the cup and remove the hard objects stuck on the blade, or mixture that exceeds the safety line, so just pour out a little.
5. Er/Lo” flashes alternately when in charging?
   • The battery pack fails, so replace the battery pack or return it to the factory for repair.
6. Leaking?
   • The silicone ring is not in the right place, please clean the silicone ring or reassemble the silicone ring.

Special attention!

After 10 times of continuous use, you should wait more than 10 minutes before you can continue to use to Prevent components from being damaged or another risk due to high temperature!

Food labeling

Precautions for Safe Use

• A Product Designed and Powerd by LeeGoal
• E-mail:vip@leegoal.com
• URL：www.Leegoal.com

LeeGoal Innovation and Creation

• LeeGoal was originally a company that invented products around healthy because we knew “Health is wealth”.
• We look for the original intention of each product when it was created, and seriously solve your problems. We never thought we would be a great company, but we would certainly do it to be a reliable company. We strive for a high-quality product and customer experience. We would love to hear your feedback and suggestions. We take all reviews and input seriously for product improvement. Any questions please contact us at vip@leegoal.com.
• Creation is an important part of who we are and how we’ve done business since our doors opened, We have long believed that we build our business by building the world we live in. We’ve got to give a little love, have a little hope, try a little more. Let’s do what we can do together. Every purchase you make will contribute to the world⸺We would like to make a Joint Donation to the Red Cross to help people in disasters. Just share your honest feedback on our LeeGoal products whether on Amazon or any social media site then email us at vip@leegoal.com so that we can finish the donation on behalf of “us”

References

• Leegoal® Blender Bravo | Redefine The Portable Blender – LEEGOAL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>