amazon basics B089XB2X4RJ Contemporary Stamford Door Levers User Manual
- June 15, 2024
- amazon basics
Table of Contents
Contemporary Stamford Door Levers
B089XB2X4RJ Contemporary Stamford Door Levers
Important Safeguards
Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.
When using the product, basic safety precautions should always be followed to
reduce the risk of injury including the following:
NOTICE This product is classified as “full indoor type” and should only
be installed in indoor environment.
(For model BO9XB2X4RJ and BO9XB3M2Q3)
Close and lock the door by using the thumb-turn button on the inside lever.
When locked, on the outside, the door lock can be opened with a coin or
emergency release tool.
- This product must be assembled by an adult.
- Keep children and pets away while assembling the product.
- Do not let children play with the product.
- Do not use this product if any parts are missing, damaged, or worn.
- Do not over-tighten the fasteners.
- Regularly examine the product for wear and tear. Stop using the product at first sign of damage or if parts become detached.
- No lock can provide complete security by itself. This product may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. The builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, consult a qualified locksmith or other security professionals.
Product Description
B09XB2X4RJ/B09XB3M2Q3
(A) Exterior lever (with bracket)
(B) Latch
(C) Latch face plate x2
(D) Drive-in collar
(E) Screw x4
(F) Strike plate
(G) interior chassis
(H) Bolt x2
(I) interior rose
(J) Interior lever
(K) Lever catch tool
B09XB37HRY / B09XB3SB47
(A) Exterior lever (with bracket)
(B) Latch
(C) Latch face plate x2
(D) Drive-in collar
(E) Screw x4
(F) Strike plate
(G) interior chassis
(H) Bolt x2
(I) Interior rose
(J) interior lever
(K) Lever catch tool
Installation
For additional illustrated installation steps, refer to the end of the written
instructions. The steps are for left-handed doors. Reverse the lever position
for right-handed doors.
NOTICE Determine the door handing before installing the product.
Face the door from the exterior side:
- If the hinges are installed on the left, the door is left- handed.
- If the hinges are installed on the right, the door is right-handed.
Before First Use
DANGER Risk of suffocation!
Keep any packaging materials away from children and pets — these materials are
a potential source of danger, e.g. suffocation.
- Remove all the packing materials.
- Remove and review all components before starting installation.
- Check the product for transport damages.
Cleaning and Maintenance
- Toclean the product, wipe with a soft, slightly damp cloth.
- Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.
- Regularly check that all the components and fasteners are tightened.
Disposal
Dispose of the product according
to local regulations.
If in doubt, consult your local authorities.
Specifications
Door thickness | 1-3/8 to 1-3/4″ (35 to 45 mm) |
---|---|
Backset | 2-3/8″ (60 mm) or 2-3/4″ (70 mm) |
Latch bolt | Zinc alloy latch bolt with 1/2″ (12.7 mm) throw |
Frequently Asked Questions
Problem | Solution |
---|---|
The latch does not retract easily when rotating the turn piece. | Ensure the |
position of the strike plate on the door frame is aligned with the position of
the latch.
Door jammed while attempting to lock.| Reposition the strike plate.
Feedback and Help
We would love to hear your feedback. To ensure we are providing the best
customer experience possible, please consider writing a customer review.
Scan QR Code below with your phone camera or QR reader:
https://www.amazon.com/review/review-your-purchases/listing/?ref=HPB_UM_CR
If you need help with your Amazon Basics product, please use the website or
number below.
amazon.com/gp/help/customer/contact-us
+1 877-485-0385
Instructions for doors with existing holes
Drilling instructions
P.48 – 55
Confirm that the hole in door edge is 01″ (25.4 mm) and the door is between 1-3/8″ (35 mm) and 1-3/4″ (45 mm) thick. Also confirm that the hole in the door is 2-1/8″ (54 mm).
Hold the latch (B) with the latch face plate (C) flush against the door edge.
Ensure that the square hole is not tilted and it is centered in the door hole.
Adjust the latch if needed.
Optional – for doors with chiseled pocket: pry open the attached latch face plate (C) and replace it with the rectangular one.
Optional – for doors without chiseled pocket: pry open the attached latch face plate (C). Remove the face plate holder and attach the drive-in collar (D).
Latch with face plate (C): fit it into the hole and secure with 2 screws (E).
/ Latch with drive-in collar (D): insert it and tap into position using a wood
block and hammer.
Latch bolt bevel must face to closing direction.
BO9XB2X4RJ / BO9XB3M2Q3
Mount the exterior lever (A) on the door. The spindle and the middle bolt of
the lever must pass through the slot on the latch (B).
Use the lever catch tool (K) to detach the interior lever (J) from the interior rose (I). Pry to detach the interior chassis (G) from the interior rose (I).
Mount the interior chassis (G) on the door with 2 bolts (H). Attach the interior rose (I} and interior lever (J) on the interior chassis (G) . Ensure the orientation of the interior chassis (G) for the door is correct.
Ensure that the door frame hole is at least 1″ (25 mm) deep. Mount the strike plate (F) on the door frame with 2 screws (E).
Use template to mark holes on door. Fold template along fold line and place it along the door edge. Select the drilling point for different door thickness: 1-3/8″ (35 mm), 1-9/16” (40 mm) or 1-3/4″ (45 mm).
Drill the holes using chisel and circular drill bits.
NOTICE Drill from one side until the drill just breaks through, then
complete hole from the other side to prevent wood from splintering.
Mark the outline of the face plate (C). Chisel 1/8″ (3 mm) deep for the face plate (C).
Mark the positions of the screw holes. Drill 2 1″ (25 mm) deep holes for each face plate using 1/8″ (3 mm) drill bit.
Close the door and mark the top and bottom position of the latch across the door frame. Open the door and measure the distance X from the exterior door edge to the flat end of the latch.
Mark a vertical line on the door frame for the measured distance X from the outside to the inside. Align the strike plate (F) with the 3 guidelines. Mark and drill two 1° (25 mm) deep screw holes using 1/8” (3 mm) drill bit.
Mark and drill a 1/2″ (13 mm) deep hole for the lever at intersection of horizontal and vertical lines of the cutout of the strike plate (F).
Chisel 1/16″ (1.6 mm) deep for the strike plate (F).
amazon.com/AmazonBasics
MADE IN TAIWAN
V01 -06/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>