TRENDnet TEW-929DRU Dual Band Wireless Gigabit Dual WAN VPN SMB Router Installation Guide
- June 15, 2024
- TRENDnet
Table of Contents
TRENDnet TEW-929DRU Dual Band Wireless Gigabit Dual WAN VPN SMB Router
- Before You Start
- Quick Reference
- Hardware Installation and Configuration
https://www.trendnet.com/qig/1215
Before You Start
Package Contents
- TEW-929DRU
- Quick Installation Guide
- 2 x detachable high gain antennas
- Network cable (1.5 m / 5 ft.)
- RJ-45 to RS-232 console cable (1.5 m / 5 fl.)
- Power adapter (12V DC, 2A)
- Rack mount kit
Minimum Requirements
- A computer with a wired or wireless network adapter and web browser
- Broadband internet
- Installed modem
- Network cable
Optional Equipment
- EIA standard 19″ rack
Quick Reference
- By default, the admin password used to log into the router configuration, wireless network name/SSID, and wireless encryption settings have been pre-configured for your convenience and can be located on the included preset wireless settings sticker or on the device label located at the bottom of the router. By default, the router web management configuration page can be accessed from LAN ports 1-3 using the URL http://tew-929dru or using the LAN IP address http:l/192.168.10.1 and WAN1 default configuration is set to DHCP client for Internet connectivity. You can choose to quickly set up your router using the diagram below and use the pre-configured settings or refer to the next section for more detailed instructions on initial installation and configuration.
Hardware Installation and Configuration
It is recommended that you configure the wireless router from a wired computer.
-
Attach the antennas to the front of the router and position them for the best Wi-Fi coverage. It is recommended that you position both of the antennas vertically as shown.
-
Connect a network cable from the WAN1 port of your router to your modem.
-
Connect a network cable from one of the LAN ports (1-3) of your router to your computer
-
Connect the included power adapter from a power outlet to your router power port and push the Power On(-)/ Off(o) switch into the On(-) position..
-
The Power ( t!> ), 2.4G and 5G LEDs will turn on solid indicating that the router is ready.
-
Open your web browser on the connected computer and in the address bar, enter http://tew-929dru or http://192.168.10.1 and press Enter to access the router web configuration page.
-
Enter the default User Name and Password, then click Login. By default, the pre-configured user name and password are located on the included preset wireless settings sticker or device label located on the bottom of the router.
-
To change the administrator password for the router configuration, click Management and click Administration.
Note : By default the administrator password has been pre-configured for your convenience and can be located on the included wireless settings sticker or on the device label located on the bottom of the router. If you are modifying the administrator password, you will need to login to the router configuration using the new password. -
Enter the new administrator password in the Password field and re-type the new password in the Confirmation field. Click Apply to save and commit the changes.
-
To change your router’s LAN 1Pv4 address settings, click on Network and click LAN.
-
Under Common Configuration and General Setup, enter the new LAN 1Pv4 address and subnet mask in the 1Pv4 address and 1Pv4 netmask fields. Click Apply at the bottom of the page to save and commit the changes. Please wait for the new address settings to be applied and log back into the router web configuration page using the new LAN 1Pv4 address.
Note : If your computer IP address settings are not automatically updated to the new settings, you may need to manually renew your computer IP address settings in order for you to log back into the router web configuration with the new LAN 1Pv4 address settings.
-
To configure your WAN1 Internet connection settings, click Network and click WAN.
-
Under Common Configuration and General Setup, click the Protocol drop-down list and select the appropriate protocol (Static address, DHCP client, PPTP, PPPoE, L2TP) for your Internet connection. DHCP client is the typical protocol in which the connection settings are automatically obtained by your ISP (Internet Service Provider). If you are unsure about the Internet connection settings, please contact your ISP (Internet Service Provider) for details. After you have completed the Internet connection settings, click Apply to save and commit the changes.
-
To configure your wireless network name/SSID and wireless encryption settings, click Wireless and click the wireless band you would like to configure. Wireless 2.4GHz or Wireless 5GHz.
Note: By default, the wireless network name/SSID and wireless encryption has been
pre-configured for your convenience and can be located on the included wireless settings sticker or on the device label located on the bottom of the router. If you are modifying the wireless settings, you will need to connect to the router with your WiFi clients using the new settings. -
To change the wireless network name/SSID for the selected wireless band, under Interface Configuration and General Setup, enter the new name in the ESSID field and click Apply to save and commit the changes.
Note : The wireless network name/SSID is the name your Wi-Fi clients will need to search and discover when connecting to your router wireless network.
-
To change the wireless encryption key for the selected wireless band, under Interface Configuration and Wireless Security, enter the new encryption in the Key field and click Apply to save and commit the changes.
Note : WPA3-PSK AES wireless encryption is strongly recommended. By default, WPA3-PSK/WPA2-PSK mixed mode is configured for client compatibility. The wireless encryption key is the key your Wi-Fi clients will need to enter when connecting to your router wireless network.
- To download the latest version of the user’s guide, please go to http://www.trendnet.com/support and select the TEW-929DRU within the Product Download drop-down list.
Federal Communication Commission Interference Statement
- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This device is restricted for indoor use.
IMPORTANT NOTE:
FCC Radiation Exposure Statement
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 42cm between the radiator & your body.
- This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
- This radio transmitter [6337A-TEW929DRU] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
- The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate.
IMPORTANT NOTE
IC Radiation Exposure Statement
- This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26cm between the radiator & your body.
Certifications
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received. Including interference that may cause undesired operation.
- Waste electrical an electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or Retailer for recycling advice.
- Applies to PoE Products Only: This product is to be connected only to PoE networks without routing to the outside plant.
Note
- The Manufacturer is not responsible for any radio or 1V interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.