OSOTEK H200 Cordless Wet Dry Vacuum Cleaner and Mop and Wash 3 in 1 User Manual

H200 Cordless Wet Dry Vacuum Cleaner and Mop and Wash 3 in 1
User Manual

Safety Instructions

Household use only.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE), Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
WARNING– To reduce the risk of fire, electric shock, or injury.

• Use indoors only during charging and cleaning mode.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children, pets or plants.

• Use only as described in this manual. Use only manufacturer’s recommended attachments

• To Reduce the Risk of Fire due to internal component damage, use only OSOTEK cleaning fluid intended for use with this appliance. See the Cleaning Fluid section of this manual.

•  To Reduce The Risk Of Electric Shock – Use indoors only during charging and cleaning mode.

• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.

• Any servicing should be done with the appliance disconnected from the supply circuit.

• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle charger, including charger plug, and charger terminals with wet hands

• Risk Of Injury. Brush May Start Unexpectedly. Keep the power off Before Cleaning or Servicing.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• Use extra care when cleaning on stairs.

•  Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Do not use without filter in place.

• Turn off all controls before unplugging.

• Do not remove the brush roll and its cover when the main unit is working.

• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack, picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing appliance that have the switch on invites accidents.

• Have servicing performed by a qualified repair person using only identical replacement parts.This will ensure that the safety of the product is maintained.

• Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care.

• This appliance contains batteries that are only replaceable by skilled persons.

• The appliance is only to be used with the power supply unit provided with the appliance.

• This vacuum is for indoor use only. Do not use or install it in outdoor, industrial, or commercial environments. Do not use the charging dock in humid environments such as bathrooms.

• Do not touch the plug or any part of the vacuum with wet hands.

• A hazard may occur if the appliance runs over the supply cord.

• The plug must be removed from the socket-outlet before cleaning or maintaining the appliance.

• Neither use the vacuum to pick up flammable or explosive liquids such as gasoline, nor other liquids such as water or toxic liquids like bleach, ammonia, and drain cleaners.

• To reduce the risk of fire, explosion, or personal injury, check before use to make sure the lithium battery and power cord are undamaged. Do not use the vacuum if either the lithium battery or power cord is damaged.

• The main body and the floor brush of the vacuum are electrically conductive and should not be immersed in water or other liquids.

• Clean the dirty water tank in time to avoid the decrease of suction and overheating of the motor caused by obstruction. Otherwise, the service life of the vacuum may be affected. Do not use the vacuum if the roller brush bar, the dirty water tank, and the filter are not installed in place.

• Make sure to turn off the vacuum before replacing the roller brushbar.

• Do not use the vacuum to clean up toner used in laser printers and copiers, as toner may cause fire or explosion.

• Do not use the vacuum to pick up smoking or burning materials such as charcoal, cigarette butts, or matches.

• Do not use the vacuum to pick up sharp or hard objects, such as glass, nails, screws, or coins, which may damage the vacuum.

• Do not use the vacuum to clean stains of thick oily substances, strong adhesives, or dyes, such as shoe polish, paints, and pigments.

• Do not put any object into the vacuum’s openings, nor use the vacuum with any opening blocked. Keep free of dust, lint, hair, or other items which may reduce airflow.
  o not shake the vacuum up and down or hit it violently to prevent dirty water from flowing into the motor.

• Do not lift or move the vacuum while the motor is operating, nor tilt it to one side to prevent dirty water from entering the motor.

• Do not place the vacuum on unstable surfaces such as chairs or tables to prevent damage or personal injury caused by its falling off. If the vacuum malfunctions because of being knocked over or damaged, please contact the authorized service department. Never attempt to disassemble the vacuum on your own.

• Do not block the drying air outlet on the charging dock to avoid malfunctions.

• Do not rinse the charging dock with water.

• Do not charge or store the vacuum near heat sources or in humid areas, such as by a radiator or in a kitchen or bathroom.

•  Only use replacement parts that are approved by OSOTEK.

• Do not repair the vacuum on your own when it breaks down or has problems like electric leakage, overheating motor, making unusual sounds, overheating main body, giving off bad odors, or weak suction.

• Do not use any third-party battery or power cord. The vacuum can only be used with the model BLJ24WD260090P-U power supply.

• Fire Hazard Warning: Do not apply any type of fragrance to the vacuum’s filter. These types of products are known to contain flammable chemicals which may cause the vacuum to catch fire.

• Do not use the appliance at ambient temperature above104°F(40°C) or below 43°F (6°C).

•  Storage Temperature: 32°F (0°C) to 104°F(40°C).

Battery Pack and Charging

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 266°F(130°C)may cause explosion.
• Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
• Battery charging can only be performed at the ambient temperature between 43°F (6°C) to 104°F(40°C). Excessively high or low temperature may extend the battery charging time, and even damage the battery. The normal charging of this product takes about 4-5 hours, so as to fully activate the battery.
• For use only with BLJ24WD260090P-U power supply.

SAVE THESE INSTRUCTIONS

| Direct current
---|---
| Alternating current
| Power Bottom

Transportation
It is recommended to transport the vacuum cleaner in its original packaging.
Precautions for Using Cleaning Solution

1. Please use the specified cleaning solution. Please use the cleaning solution as instructed to prevent any danger caused by excessive bubbles entering the motor.
2. Keep the cleaning solution out of reach of children. In case of contact with eyes, rinse immediately with plenty of water. In case of accidental ingestion, seek medicaladvice immediately.
3.  Please comply with local environmental regulations when disposing of the dirty water and cleaning solution.

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference, and
   (2) This device must accept any interference received, including interference that may cause undesired operation.

Product Overview

Vacuum Self-cleaning Charging Dock

Accessories

Note: All pictures of products, accessories, user interface, etc. shown in the manual are for illustration purpose only. Actual product may vary due to product updates/enhancement.

Installation

Install the Roller Brush

1. Press the two removal keys of the roller brush cover inward at the same time to remove the roller brush cover.
2. Remove the brush protector.
3. Press the roller brush holder as shown, put the roller cloth on the roller brush holder, and press the roller cloth firmly to install it in place.
4. Install the roller brush, rotate the lock to the locked position and install the roller brush cover Tips: When a new dry roller brush is used for the first time, it is normal for it to vibrate slightly when it rubs against the ground. The roller brush can be used normally after it is completely wet.

Installing the Handle
Insert the handle upright into the main unit until you hear a click, which indicates that it is locked. Then reconfirm that it is secured in place.
Removing the Handle
Use a non-sharp tool to hold down the handle release button on the back of the main unit, while pulling the handle upright. Installing the Self-cleaning Charging Dock

1. Installing the Power Cord
   Plug the power cord into the power port at the bottom of the self-cleaning charging dock, then wind and store the excess power cord.

2. Installing the Mounting Clip
   Install the mounting clip onto the installation slot on either side of the bottom of the self-cleaning charging dock.

3. Installing the Accessory Container
   Install the accessory container onto the mounting clip.

4. Storing the Accessories
   The container can store the cleaning brush, the roller brush bar, and the filter.
   Note: The spare roller brush bar and the spare filter need to be purchased separately.

How to use

Connecting to an Electrical Outlet
Place the self-cleaning charging dock on a flat surface and connect it to power via the power supply.
Note:
Keep the self-cleaning charging dock away from heat sources such as radiators or humid environments such as kitchens and bathrooms. Charging the Main Unit
After powering on the self-cleaning charging dock, align the charging electrode at the bottom of the cleaner head with the charging electrode of the self-cleaning charging dock, and the charging starts until you hear the “charging” voice alert. Notes:

• The battery level is shown in numbers on the LED screen.
• 20s after the battery is full, the LED screen will go off.

Note:

• Please fully charge the main unit before the first use and after each use (charging time: 4-5h). The battery may overheat after continuous use for cleaning stubborn stains. In this case, it’s normal that the charging may take longer or the battery level may remain constant in a short time.

Intended Use
The product is designed to clean hard floor surfaces such as floor, tile and marble.
Note:
The cleaner head lighting is on by default when the product is turned on.The product also works when lying flat on the floor, ideal for cleaning the floor surface below the furniture bottom. Cautions:

• Do not use it on fabrics such as carpets or blankets.
• Do not tip the product forward or shake it vigorously to prevent dirty water from flowing out.

Buttons

Press & hold, and then short press this button to change the language:
Press and hold this button for 3s to broadcast voice alerts in the current language, that is, enabling the language switch. Then, if no operations are performed within 5s, the current language will be still used; If you press the voice control button within 5s, the language will be switched to the next one. If you perform no operation within 5s after that, the switched language will be used, and so on.
LED Screen The Dirtiness/Error Indicator indicates the following information:

• Floor dirt detection
  Blue (always on) – clean
  Red (always on) – dirty

• Error status
  Red (flashing 5s then stay on) – Fault
  For detailed troubleshooting solutions, refer to Page 18 of the User Manual.

Water Adding

1. Press the clean water tank release button, and simultaneously pull the tank out.
2. Open the filling port of the clean water tank, slowly fill it with a proper amount of clean water, and then close it.
   Notes:
   • You can also add an appropriate amount of officially designated cleaning solution.
   • Do not add hot water, unofficial cleaning solution or disinfectants.

Cleaning Fluid Section
WARNING:
To Reduce the Risk of Fire and Electric Shock due to internal component damage, use only OSOTEK cleaning fluid intended for use with the appliance.
How to Clean

• Remove the vacuum from the self-cleaning charging dock, step on the floor brush with one foot and pull back the handle to tilt the vacuum.
• Press the button to turn on the vacuum.

Switching Modes
Press 0 to switch from Auto Mode, Turbo Mode, to Suction Mode.

suck up dust)

CAUTION:
Do not rotate the vacuum from side to side while lying it down for cleaning to prevent the floor brush from tilting up or dirty water from running out. Stop Cleaning/OFF
Hold the vacuum in the upright position to pause cleaning, or press the button to turn off the vacuum. To avoid dirty water residues, the vacuum will continue running for a few seconds before turning off. Place the vacuum back onto the self-cleaning charging dock after it completely stops working.
When the vacuum is paused in the upright position or turned off, pull the handle backward, and push the vacuum to the self-cleaning charging dock with the help of wheels. Then you can use the dock for storage, charging, and self- cleaning.
Notes:

• Put the vacuum back onto the self-cleaning charging dock properly after using it to prevent the vacuum from tipping over due to improper placement.
• To prevent dirty water from flowing out, do not vertically uplift the whole main unit (as shown in the figure below).

Self-cleaning

• When the vacuum is charging and its battery level is equal to or more than 10%, press to start self-cleaning.
• Press the button or the button to stop self-cleaning.
•  Based on how dirty the roller brush bar is, it will take about 2 to 3 minutes for the vacuum to complete the self-cleaning.

Notes:

• Clean the dirty water tank in time after self-cleaning to prevent odors.
• It is recommended to remove the roller brush bar after self-cleaning and place it in the accessory container for drying to prevent odors.
•  It is recommended to regularly clean parts that cannot be cleaned by self-cleaning, such as the roller brush bar cover and the parts around the suction port.

Care & Maintenance

CAUTIONS:

• Clean and maintain the relevant components when the vacuum is paused in the upright position or turned off.
• Move the self-cleaning charging dock away before cleaning the vacuum.

Maintenance Frequency

Dirty water tank components (including the dirty water tank, the dust compartment, and the water level sensor)| Clean after each use.
Dirty water outlet pipeline (including the dirt detection sensor)| Clean when prompted by relevant voice notification.
Water & Air Separator| 1–3 months
Floor brush (overall)| Clean once a week, depending on the dirtiness.
Roller Brushbar| Self-cleaning is required after each use.
Filter| Clean it monthly.
Self-cleaning Charging Dock| Clean once a week.

Replacement Frequency
Note:
The following recommended replacement frequencies are for reference only. Components should be replaced promptly if damaged.

Cleaning the Dirty Water Tank

1. Press the dirty water tank release button, while pulling the tank out.

2. Hold the bottom of the dirty water tank, while pressing the button on the top of the dirty water tank. Take out the solid waste bin upward, and empty the solid waste and dirty water respectively.

3. Rinse the dirty water tank and solid waste bin with tap water.
   Notes:
   • Use the cleaning tool for assist.
   • Clean the full tank sensor frequently to avoid adhesive stains from affecting its detection accuracy.

4. Install the solid waste bin, then re-install the dirty water tank onto the main unit until you hear a “click”, which indicates it is installed in place.

Cleaning the Floor Brush

1. Press both roller brush bar cover release buttons inward at the same time to remove the roller brush bar cover.

2. Rotate the brush roll latch counterclockwise to the UNLOCKED position, and pull out the brush roll.

3. Rotate the handle of the cleaning brush to remove the blade. Use the blade to cut the hair tangled on the roller brush bar and the floor brush.

4. Use tap water to rinse the roller brush bar and its cover until they are clean, and then put them in the accessory container for drying to prevent odors.
   Note: Do not expose the roller brush bar to direct sunlight.

5. Use a dry cloth or paper towel to remove the hair, dirt, and foreign objects blocked at the suction port.
   Notes:
   • Do not rinse the floor brush directly.
   • Do not touch the gearbox right after using the vacuum to avoid scalds.

6. Reinstall the roller brushbar and its cover in order. When reinstalling the roller brushbar cover, align it with the mounting position, and it is secured in place when you hear a click.

Cleaning the Water & Air Separator
It is normal to find a small amount of dirty water around the water & air separator after removing the dirty water tank. Please wipe the dirty water away. Cleaning the Filter
Pull out the filter from the top left corner of the dirty water tank’s mounting slot as illustrated.
Rinse the filter clean under tap water, then dry it or put it in the accessory container to dry before reinstalling to prevent odors. Cleaning the Dirt Detection Sensor
Take out the dirty water tank, and use the cleaning brush to clean the dirt detection sensor and the pipeline of the dirty water outlet. Cleaning the Self-cleaning Charging Dock
Disconnect the self-cleaning charging dock from the power supply before cleaning the dock.
Use a dry cloth or paper towel to clean the dust from the self-cleaning charging dock.
Note: Do not rinse the self-cleaning charging dock directly with water to prevent short circuits.

Cleaning the Vacuum
Stand the vacuum upright, and use a dry cloth or paper towel to clean the dust from the vacuum.

Troubleshooting

The display will show an error message or a voice notification will be played when the vacuum is not working normally, please refer to the table to find the solution. If the error cannot be solved by the solution, please contact the after-sales service team in time.

clean water tank before use.
| Please check and clean the roller brush.| Check whether the brush roll is entangled or blocked by foreign objects
| Please clean the dirty water tank.| Clean the dirty water tank and reinstall it.
| Re-install the dirty water tank| Please re-install the dirty wat, tank correctly
Reinstall the roller brush bar.| Reinstall the roller brush bar properly.
Please clean the pipes and dirty water tank.| Check whether the suction port of the floor brush and the pipeline of the dirty water outlet are blocked, and clean the dirty water tank.
The sensor is dirty, please clean the pipeline of the vacuum.| Clean the dirt detection sensor.
Fault code| Contact the after-sales service team.

Common Issue

before use.
The battery has overheating protection.| Try again after the battery temperature returns to normal.
Clean water tank, dirty water tank, or roller brush bar is not installed.| Install the clean water tank/dirty water tank/brush roll correctly
Full Dirty Water Tank| Clean the dirty water tank and reinstall it.
The clean water tank is out of water.| Add water to the clean water tank and reinstall the tank.
The suction port of the floor brush or the pipeline of the dirty water outlet is blocked.| Clean the suction port of the floor brush and the pipeline of the dirty water outlet.
The roller brush bar is tangled with foreign objects.| Clean the roller brush bar.
Dirty water recycling error of the main unit| The filter is not installed.| Install the filter before use.
Unable to charge the main unit| Self-cleaning charging dock not powered on| Use the original power supply to power the self-cleaning charging dock
The power supply being used is not original.| Use the original power supply.
The vacuum has no voice notification.| The voice notification is disabled.| Press and hold the voice button for three seconds to enable voice notification.
The vacuum cannot carry out self-cleaning.| The clean water tank is out of water.| Add water to the clean water tank and reinstall the tank.
The clean water tank is not installed.| Reinstall the clean water tank.
The dirty water tank is full.| Clean the dirty water tank and reinstall it.
The dirty water tank is not installed.| Reinstall the dirty water tank.
The battery is low or depleted.| Carry out self-cleaning when the battery level is sufficient.
Self-cleaning charging dock not powered on| Use the original power supply to power the self-cleaning charging dock

Specifications

OSOTEK Horizon Wet Dry Vacuum H200

Self-cleaning Charging Dock

Power Supply

Environmental Notice

The lithium-ion battery pack contains substances that are hazardous to the environment.
Before disposing of the vacuum, please first remove the battery pack, then discard, or recycle it in accordance with local laws and regulations of the country or region it is used in.
CAUTIONS:

• Remove the entire battery pack together, and make sure not to damage the outer casing of the battery pack to prevent short-circuiting or leakage of harmful substances.
• In the event of a battery leak, avoid contact with the liquid. If the liquid enters the eyes, rinse with plenty of water and seek medical attention immediately.
• The battery should not be removed by non-professionals. Otherwise, it may lead to a short circuit or other risks. It is recommended to send the product to the professional after-sales service team or a government-approved recycling facility for removal.

Steps to Remove the Battery:

1. Use a non-sharp tool to press and hold the handle release button on the back of the vacuum, and simultaneously pull the handle upwards vertically.
2. Remove the dirty water tank.
3. Unscrew the display assembly to remove it.
4. Remove the rear cover of the vacuum by unscrewing the bottom cover, the front cover, and the rear cover of the vacuum.
5. Unscrew the battery pack assembly to remove it.
6.  Unscrew the top and bottom covers of the battery pack assembly and remove the top cover.
7.  Unscrew the battery pack assembly, and unplug the battery pack to remove it.

Warrant Information
The warranty period depends on the laws of the country in which the product is sold, and the warranty is the responsibility of the seller.
The warranty only covers defects in material or workmanship.
The repairs under warranty may only be carried out by an authorized service center.
When making a claim under the warranty, the original bill of purchase (with purchase date) must be submitted.
The warranty will not apply in cases of:
i. Failures caused by:

1.  Use of a OSOTEK product which is not in accordance with the “Usage Restrictions” in the User Manual.
2. Use of a OSOTEK product for cleaning white ashes, sand and other non-household garbage.
3.  Use of a OSOTEK product for decoration, ornament or cleaning in a commercial environment.
4.  Use of a OSOTEK product for cleaning in an environment with special adsorption chemicals, metal or other microparticles.
5. Use of a OSOTEK product in an environment with corrosive objects.
6. Use of a OSOTEK product in an improper voltage supply environment.
   ii. The product you purchased is a prototype, the model or SN of which does not follow the SN coding rule for a brand-new complete machine. Please consult us for any unclear terms. e-mail: support-global@osotek.com

Manufactured by: Beijing Shunzao Technology Co., Ltd.
Address: 101, 1st floor, Building 1, No.16, Anningzhuang East Road, Haidian District, 100089 Beijing, PEOPLE’s REPUBLIC OF CHINA
For further information, please go to www.osotek.com
User Manual Version: V1.0

References

• OSOTEK Wet Dry Vacuum Technology │ Beyond Your Expectation - OSOTEK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>