DEWINNER ET1502 Cordless Grass Shear and Hedge Trimmer Instruction Manual

DEWINNER ET1502 Cordless Grass Shear and Hedge Trimmer

Specifications

• Type : Cordless Grass Shear & Hedge Trimmer
• Battery voltage : DC 7.2V
• Battery type : Lithium-Ion
• No load speed : 1000rpm
• Cutting length : 170mm
• Cutting width: 100mm
• Battery capacity: 1.5Ah
• Charging time: 3-5 hours
• Net weight : 1Kg (no swivel handle), 1.4Kg (with swivel handle)

WARNING

• READ THIS MANUAL BEFORE USING For your safety and for proper operation and maintenance, please read carefully and keep readily available for future reference.

IMPORTANT TIPS

1. Unit is fully assembled. Remove clear plastic blade guard before use and save it to use as blade-cover when unit is not in use.
2. Battery must be charged before use. Please refer to battery charging instructions.
3. If the blade becomes jammed on a branch while cutting, IMEDIATELY release trigger and clear jam. If you continue to hold trigger with blade jammed you will damage the motor
4. IMPORTANT : This is a powerful tool that is remarkably easy and comfortable to use. As such, please pay attention to the placement of the blades while using to avoid cutting yourself.

TECNICHAL SPECIFICATIONS

SAFETY INSTRUCTIONS

Please read these instructions before operating this product and save these instructions. For safe operation

1. Keep children and animals away from working area.
2. Switch on motor only when the hands and feet are away from the cutting blades.
3. Use only the manufactures recommended replacement parts and accessories.
4. When not in use, tools and batteries should be stored separately in a dry, high or locked up place, out of reach of children. Ensure that battery terminals cannot be short-circuited by other metal parts such as serews, nails, etc.
5. Do not use excessive pressure during operation. It will do the job better and safer at the rate for which it was intended.
6. Dress properly Do not wear loose clothing or jewelry; they can be caught in moving parts. Wear stout shoes while using the grass shear. Wear protecting hair covering to contain long hair.
7. Maintain tools with care Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubrication and changing accessories.
8. Disconnect tools Disconnect the tool from its battery pack when not in use, before servicing and when changing accessories such as blades.
9. Avoid unintentional starting Do not carry the tool with a finger on the switch.
10. Stay alert Watch what you are doing. Use common sense. Do not operate the tool when you are tired.
11. Warning The use of any accessory or attachment, other than recommended in this instruction manual, may present a risk of personal injury. Ensure that the battery pack is correct for the tool. Ensure that the outside surface of battery pack or tool is clean and dry before plugging into charger. Ensure that batteries are charged using the correct charger recommended by the manufacturer. Incorrect use may result in a risk of electric shock, overheating or leakage of corrosive liquid from Incorrect use may result in a risk of electric shock, overheating or leakage of corrosive liquid from the battery.
12. Have your tool repaired by a qualified person This tool is constructed in accordance with the relevant safety requirements. Qualified persons using original spare parts should only carry out repairs; otherwise this may result in considerable danger to the user.
13. Disposal of battery Ensure battery is disposed of safety as instructed by the manufacturer.

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER

1. Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using battery pack.
2. DANGER: 230 volts present at charging terminals. Do not probe with conductive objects. Danger of electric shock or electrocution.
3. The charger and battery are specifically designed to work together. DO NOT attempt to charge the battery with any chargers other than the ones in this manual.
4. Do not expose charger to rain or snow.
5. This charger is not intended for any uses other than charging rechargeable batteries. Any other uses may result in risk of fire, electrie shock or electrocution.
6. To reduce risk of damage to electric plug and cord, disconnect from mains socket by pulling the plug rather than the cord.
7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
8. The charger is ventilated through slots in the top and the bottom of the housing. Do not place any object on top of charger or on a surface that might block the ventilation slots and result in excessive internal heat. Place the charger in position away from any heat source.
9. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way.
10. Do not disassemble charger. Take it to authorized service center when service or repair is required. Incorrect reassemble may result in a risk of electric shock, electrocution or fire.
11. To reduce risk of electric shock, unplug charger from outlet before attempting any cleaning. Removing the battery pack will not reduce this risk.
12. Never attempt to connect 2 chargers together.
13. DO NOT store or use the tool in locations where the temperature may reach or exceed 105°F (such as outside sheds or metal buildings in summer).
14. The charger is designed to operate on standard household electrical power (230volts). Do not attempt to use it on any other voltage!

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY

The battery is not fully charged when you first receive it. First read the safety instructions below the follow charging notes and procedures.
READ ALL INSTRUCTIONS CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

1. Do not incinerate the battery even if it is severely damaged or is completely worn out. The battery can explode in a fire.
2. A small leakage of liquid from the battery cells may occur under extreme usage or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin
   • Wash quickly with soap and water.
   • Neutralize with a mild acid such as lemon juice or vinegar.
   • If battery liquid gets in your eyes, flush them with clean water for a minimum of minutes and seek immediate medical attention. (medical notes: the liquid is 25-35% solution of potassium hydroxide.)
3. Do not connect the positive pole and the negative pole of the battery with any metal objects. Battery could be short circuited causing damage to the battery and possibly causing severe burns or fire.
4. Charge the battery only in the chargers supplied with the product.
5. NOTE : the battery in your tool is the lithium-ion type, with no self-discharge or memory effect.

ASSEMBLY

Fitting/removing the wheels assembly

Fitting the wheels assembly

• Push the wheels assembly forward into the grass shear align the slot until both catches click into suitable place.

Removing the wheels assembly

• Pull the wheels assembly backwards and remove.

WARNING

• Do not turn on the switch when you fit or remove the wheels assembly. This can cause a serions iniurv

Fitting/removing the telescopie swivel handle

Fitting the telescopic swivel handle assembly (2)

• Guide the swivel handle assembly (2) at the desired angle between 0° and 360° into the handle holder of the wheels assembly (1) until the lock engages.

The starting lockout and ON button on the tools no longer function when the swivel handle is mounted.

Removing the telescopies swivel handle assembly (2)

• Press the release button (3) and pull out the swivel handle assembly (2).

WARNING

• Do not turn on the switch when you fit or remove the wheels assembly. This can cause a serious injury.

OPERATING YOUR TOOLS Warning

Never remove or bridge the switching devices. The starting lockout prevents your tools from being switched on unintentionally. Cutting without swivel handle

Push lock-off button

1.  forward and press switch
2.  Release the lock-off button (1) again.

Warning : Do not turn on the switch when you adjust the swivel handle. This can cause a serious injury.

1. Attach the swivel handle.
2.  Hold the tube (3) with one hand, and then loosen the adjusting bolt (4).
3. Set the handle to the correct length and tighten the adjusting bolt (4). Push lock-off button (1) forward and press switch (2).

CEO SOCCE

• Always release the On/Off switch before insertion or removal of the battery pack.
• To remove the battery pack, withdraw it from the tool while pressing the spring buttons 5 on both sides of the cartridge.
• Attention : The moving blade will move back if the moving blade is not in the fully open position when inserting the battery pack.

Battery charging Do not use other battery chargers.

• The supplied battery charger is designed for Lithium-ion battery in your machine.

Observe correct mains voltage

• The voltage of the power source must agree with the voltage specified on the nameplate of the unit. Equipment marked with 230 V can also be connected to 220 V or 240 V. The Li-ion battery is protected against deep discharging by the “Electronic Cell Protection”. When the battery is empty, the machine is switched off by means of a protective circuit: The inserted tool no longer rotates.

WARNING

• Do not continue to press the On/Off switch after the machine has been automatically switched off. The battery can be damage. The battery is supplied partially charged. To ensure full capacity of the battery, completely charge the battery in the battery charger before using your power tool for the first time. A battery that is new or has not been used for a longer period does not develop its full capacity until after approx. 5 charging/discharging cycles. When the machine can not rotate while the On/Off switch is pressed, then the battery has no enough capacity and should be charged.
• Plug the mains plug7 of the charger 6 into the socket 8 of the battery pack 5. And then Insert the charger into the power supply. At this time, the battery charge-control indicator 9 lights up. The battery charge-control indicator indicates the charging progress. The indicator lights up red during the charge procedure. The battery is completely charged when the indicator lights up green again. 26 Disconnect the battery charger from the mains supply when not using it for longer periods.

CHANGE THE BLADES

Warning! DO NOT operate the switch before dismantling or fitting the blades. Risk of injury!

The blade can be changed rapidly and expediently without any tools.

1. To change the blade, you must remove the Blade cover (A) at first. Follow the steps as shown in the upper figure. Hold the machine in one hand as showed in the upper figure. Lever the retainer (B) upwards with your thumb and forefinger of another hand.
2. Hold the blade cover firmly and pull it backwards.
3. ® Remove the blade cover upwards.

Warning!
DO NOT operate the switch before the blade cover is installed. Risk of injury!

MAINTENANCE AND REPAIR

• Do not rinse the machine with water.
• The cutter should be stored in a dry place when it is not in use.
• Before every use of this cutter, check whether the blade is in good order and it must be repaired in time if damage has been found.
• The blade should be cleaned and lubricated in time after every use of the cutter.
• When the cutter is to be used for a long time the blades should be lubricated during operations interval.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>