AJA VIDEO SYSTEMS FiDO 12G Series SDI Optical Fiber Mini Converters Installation Guide
- June 15, 2024
- AJA VIDEO SYSTEMS
Table of Contents
- AJA VIDEO SYSTEMS FiDO 12G Series SDI Optical Fiber Mini Converters
- Installation and Operation
- Introduction
- FiDO Converter Simplified Block Diagrams
- FiDO Converter I/O Connections
- Installation
- Specifications
- Safety and Compliance
- Declaration of Conformity
- Before Operation Please Read These Instructions
- Warranty and Liability Information
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AJA VIDEO SYSTEMS FiDO 12G Series SDI Optical Fiber Mini Converters
Installation and Operation
Notices
Trademarks
AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc. for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for use with recorder, router, software and camera products. Because it matters.™ is a trademark of AJA Video Systems, Inc. for use with camera products. Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered trademarks of AJA Video Systems, Inc. AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, V2Analog™ and V2Digital™ are trademarks of AJA Video Systems, Inc. All other trademarks are the property of their respective owners.
Copyright
Copyright © 2020 AJA Video Systems, Inc. All rights reserved. All information in this manual is subject to change without notice. No part of the document may be reproduced or transmitted in any form, or by any means, electronic or mechanical, including photocopying or recording, without the express written permission of AJA Video Systems, Inc.
Contacting AJA Support
When calling for support, have all information at hand prior to calling. To contact AJA for sales or support, use any of the following methods:
- Telephone +1.530.271.3190
- FAX +1.530.271.3140
- Web https://www.aja.com
- Support Email support@aja.com
- Sales Email sales@aja.com
Introduction
Overview
FiDO 12G Mini-Converters offer unmatched flexibility and cost efficiency
for 12G-SDI, 6G-SDI, and 3G-SDI Fiber conversion, allowing the transport of
12G-SDI over distances of up to 10km when using standard Single-Mode fiber
optic cable. These converters use a compact, low-profile enclosure that works
well in tight spaces around and behind equipment racks, trucks and on camera.
FiDO 12G Mini-Converters meet all relevant SMPTE specifications as well as
offering electrical isolation to eliminate potential ground loop problems for
a rugged, versatile solution that is suitable for a variety of applications.
Features
- Transport of 12G/6G/3G/HD/SD-SDI as well as DVB-ASI over optical fiber
- Auto-reclocking at SMPTE SDI rates
- All SDI ancillary data, including embedded audio, is passed
- Simplex or duplex models available
- Single Mode
- 1310nm optical Transmitter
- 1260 – 1620 wide band optical Receiver
- LC fiber connectors
- ST fiber connectors
- Coax inputs are equalized
- Coax and fiber inputs are reclocked
- DVB-ASI compatible
- Useful for eliminating ground loop problems
- 5-20VDC power supply (included)
- Five year warranty
FiDO 12G Models
- FiDO-T-12G: Single Channel 12G-SDI to Single-Mode LC Fiber Transmitter
- FiDO-T-12G-ST: Single Channel 12G-SDI to Single-Mode ST Fiber Transmitter
- FiDO-2T-12G: Dual Channel 12G-SDI to Single-Mode LC Fiber Transmitter
- FiDO-R-12G: Single Channel Single-Mode LC Fiber to 12G-SDI Receiver
- FiDO-R-12G-ST: Single Channel Single-Mode ST Fiber to 12G-SDI Receiver
- FiDO-2R-12G: Dual Channel Single-Mode LC Fiber to 12G-SDI Receiver
- FiDO-TR-12G: Single Channel 12G-SDI/LC Single-Mode LC Fiber Transceiver
Accessories
- DWP-U-R1: Power supply included
- Rackmount bracket
FiDO Converter Simplified Block Diagrams
FiDO Converter I/O Connections
- NOTE: Green illuminated LEDs labeled OPT or SDI indicate a signal has been detected and locked for that input.
- NOTE: The OPT indicator for optical receivers may flicker or glow dim with the optical input disconnected.
Installation
NOTE: AJA does not support the use of any SFP modules other than our own; use of any non-AJA SFP module will void the warranty. Installation consists of the following steps:
- Connect video equipment to the FiDO converter BNCs.
- Connect fiber to the FiDO Optical fiber connectors.
Caution! Single-mode (1310 nm) and CWDM FiDO devices require the use of “single mode 1310nm compatible” fiber optic cable.
Warning! Active fiber-optic cables emit radiation invisible to the human eye. Do not look directly at the end of an active fiber-optic cable or the fiber connector on a FiDO-T-12G, FiDO-2T-12G, or FiDO-TR-12G, ; these models are Class 1 Laser Products.
-
FiDO-2T-12G, FiDO-2R-12G, and FiDO-TR-12G require either a duplex LC cable or two simplex LC cables. Insert each connector until it latches.
-
FiDO-T-12G and FiDO-R-12G require a single simplex LC cable connected to the optical port on the converter pointed to by the arrow (Optical Output on FiDO-T-12G, or Optical Input on FiDO-R-12G).
NOTE: Fiber optic interconnections can be severely compromised by dirt, oils, or other contaminants. All dust caps should be replaced on cables and equipment whenever FiDO converters are disconnected from fiber optic cables. -
Apply +5VDC power to the converter (AJA power supply included).
Operation
FiDO series converters have no user controls. No configuration or settings are
required. Once powered, the FiDO converters will begin converting applied
fiber/ SDI signals.
Specifications
Video Formats
- 270Mbps – 12 Gbps, format agnostic
Video Input Digital – FiDO-T-12G and FiDO-T-12G-ST
- 1-channel independent 12G-SDI BNC connector, SMPTE 259/292/424/2081/2082
Video Input Digital – FiDO-2T-12G
- 2-channel independent 12G-SDI BNC connectors, SMPTE 259/292/424/2081/2082
- Video Input Digital – FiDO-R-12G
- 1-channel independent Single Mode LC Fiber connector,
- SMPTE 297/259/292/424/2081/2082
- Nominal Wavelength: Rx 1260 nm (min), 1620 nm (max)
- Optical Sensitivity: -10 dBm (min 12 Gbps), -14 dBm (min 3 Gbps)
- Overload Power: -2 dBm (min)
Video Input Digital – FiDO-R-12G-ST
- 1-channel independent Single Mode ST Fiber connector, SMPTE 297/259/292/424/2081/2082
- Nominal Wavelength: Rx 1260 nm (min), 1620 nm (max)
- Optical Sensitivity: -10 dBm (max 12 Gbps), -14 dBm (max 3 Gbps)
- Overload Power: -2 dBm (min)
Video Input Digital – FiDO-2R-12G
- 2-channel independent Single Mode LC Fiber connectors, SMPTE 297/259/292/424/2081/2082
- Nominal Wavelength: Rx 1260 nm (min), 1620 nm (max)
- Optical Sensitivity: -9 dBm (min 12 Gbps), -10 dBm (min 3 Gbps)
- Overload Power: -2 dBm (min)
Video Input Digital – FiDO-TR-12G
- 1-channel independent 12G-SDI BNC connector, SMPTE 259/292/424/2081/2082
- 1-channel independent Single-Mode LC Fiber connector, SMPTE 297/259/292/424/2081/2082
- Nominal Wavelength:
- Tx 1260 nm (min), 1310 nm (typ), 1360 nm (max)
- Rx 1260 nm (min), 1620 nm (max)
- Optical Sensitivity: -10 dBm (min 12 Gbps), -14 dBm (min 3 Gbps)
- Optical Power: -5 dBm (min), 0.5 dBm (max)
- Overload Power: -2 dBm (min)
- Extinction Ratio: 5.4 dB (min)
Video Output Digital – FiDO-T-12G
- 1-channel 12G-SDI reclocked, loop out, BNC connector, SMPTE 259/292/424/2081/2082
- 1-channel independent Single Mode LC Fiber connector, SMPTE 297/259/292/424/2081/2082
- Nominal Wavelength: Tx 1260 nm (min), 1310 nm (typ), 1360 nm (max)
- Optical Power: -5 dBm (min), 0.5 dBm (max)
- Extinction Ratio: 5.4 dB (min)
Video Output Digital – FiDO-T-12G-ST
- 1-channel 12G-SDI reclocked, loop out, BNC connector, SMPTE 259/292/424/2081/2082
- 1-channel independent Single Mode ST Fiber connector, SMPTE 297/259/292/424/2081/2082
- Nominal Wavelength: Tx 1260 nm (min), 1310 nm (typ), 1360 nm (max)
- Optical Power: -5 dBm (min), 2 dBm (max)
- Extinction Ratio: 3.4 dB (min)
Video Output Digital – FiDO-2T-12G
- 2-channel independent Single Mode LC Fiber connectors, SMPTE 297/259/292/424/2081/2082
- Nominal Wavelength: Tx 1260 nm (min), 1310 nm (typ), 1360 nm (max)
- Optical Power: -5 dBm (min), 0.5 dBm (max)
- Extinction Ratio: 5.4 dB(min)
Video Output Digital – FiDO-R-12G and FiDO-R-12G-ST
- 1-channel dual matching 12G-SDI BNC connectors, SMPTE 259/292/424/2081/2082
Video Output Digital – FiDO-2R-12G
- 2-channel independent 12G-SDI BNC Outputs, SMPTE 259/292/424/2081/2082
Video Output Digital – FiDO-TR-12G
- 1-channel independent 12G-SDI BNC connector, SMPTE-259/292/424/2081/2082
- 1-channel independent Single Mode LC Fiber connector, SMPTE-297/259/292/424/2081/2082
- Nominal Wavelength:
- Tx 1260 nm (min), 1310 nm (typ), 1360 nm (max)
- Rx 1260 nm (min), 1620 nm (max)
- Optical Sensitivity: -10 dBm (min @12 Gbps), -14 dBm (min @ 3 Gbps)
- Optical Power: -5 dBm (min), 0.5 dBm (max)
- Extinction Ratio: 5.4 dB (min)
Reclocking
- 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.967 Gbps, 2.970 Gbps, 5.934 Gbps, 5.940 Gbps, 11.868 Gbps, 11.880 Gbps – Auto Select
- All other rates are passed through and not reclocked
Size (w x d x h)
- 4.6″ x 1.71 ” x.85″ (117 x 43.5 x 21.6mm)
Weight
- 0.4 lb (0.2 kg)
Power
- 2 watts (max)
- Uses 5-20VDC power (AJA power supply model DWP-U-R1 included)
Environment
- Safe Operating Temperature: 0 to 40 C (32 to 104 F)
- Safe Storage Temperature (Power OFF): -40 to 60 C (-40 to 140 F)
- Operating Relative Humidity: 10-90% non-condensing
- Operating Altitude: <3,000 meters (<10,000 feet)
Safety and Compliance
Federal Communications Commission (FCC) Compliance Notices
Class A Interference Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, under Part 15, Subpart B of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used by the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Canadian ICES Statement
Canadian Department of Communications Radio Interference Regulations This digital apparatus does not exceed the Class A limits for radio-noise emissions from a digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. This Class A digital apparatus complies with Canadian ICES-003.
European Union and European Free Trade Association (EFTA) Regulatory Compliance
This equipment may be operated in the countries that comprise the member countries of the European Union and the European Free Trade Association. These countries, listed in the following paragraph, are referred to as The European Community throughout this document: AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA, FINLAND, FRANCE, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LATVIA, LITHUANIA, LUXEMBOURG, MALTA, NETHERLANDS, POLAND, PORTUGAL, ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN, UNITED KINGDOM, ICELAND, LICHTENSTEIN, NORWAY, SWITZERLAND
Declaration of Conformity
Marking by this symbol indicates compliance with the Essential Requirements of the EMC Directive of the European Union 2014/30/EU. This equipment meets the following conformance standards:
Safety
- EN 60065: 2014 (T-Mark License)
- IEC 60065: 2014 (CB Scheme Report/Certificate)
- EN 62368-1: 2014 + A11 (T-Mark License)
- IEC 62368-1: 2014 (CB Scheme Certificate)
- Additional licenses issued for specific countries available on request.
Emissions
- EN 55032: 2012 + AC: 2013, CISPR 32: 2015
- EN 61000-3-2: 2014, EN 61000-3-3: 2013
Immunity
- EN 55103-2: 2009, EN 61000-4-2: 2009,
- EN 61000-4-3: 2006 + A1: 2008 + A2: 2010,
- EN 61000-4-4: 2004 + A1: 2010,
- EN 61000-4-5: 2006, EN 61000-4-6: 2009, EN 61000-4-11: 2004
- Environments: E2, E3 and E4
- The product is also licensed for additional country specific standards as required for the International Marketplace
Laser
EN 60825-1: 2007 and EN 60825-2: 2004 +A2: 2010, CDRH Compliant Class 1 (TUV
Cert No. 50135086) Also Licensed for Standards: FDA 21 CFR 1040.10 and 1040.11
Recycling Notice
This symbol on the product or its packaging indicates that this product must
not be disposed of with your other household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste for
recycling, please contact your local authority, or where you purchased your
product.
Taiwan Compliance Statement
This is a Class A product based on the standard of the Bureau of Standards,
Metrology and Inspection (BSMI) CNS 13438, Class A. In a domestic environment
this product may cause radio interference in which case the user may be
required to take adequate measures.
Japan Compliance Statement
This is a Class A product based on the standard of the VCCI Council
(VCCI-32: 2016). If this is used near a radio or television receiver in a
domestic environment, it may cause radio interference. Install and use the
equipment according to the instruction manual.
Translated Warning and Caution Messages
- The following caution statements, warning conventions, and warning messages apply to this product and manual.
- Warning Symbol
- Caution Symbol
Before Operation Please Read These Instructions
- Warning! Read and follow all warning notices and instructions marked on the product or included in the documentation.
- Warning! Do not use this device near water and clean only with a dry cloth.
- Warning! Do not block any ventilation openings. Install by the manufacturer’s instructions.
- Warning! Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Warning! Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
- Warning! Since the Mains plug is used as the disconnection for the device, it must remain readily accessible and operable.
- Warning! Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the device.
- Warning! Unplug this device during lightning storms or when unused for long periods.
- Warning! Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the device, the device has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Warning! Do not open the chassis. There are no user-serviceable parts inside. Opening the chassis will void the warranty unless performed by an AJA service center or licensed facility.
- Warning! Disconnect the external AC power supply line cord(s) from the mains power before moving the unit.
- Warning! Only use attachments and accessories specified and/or sold by the manufacturer.
- Caution! FiDO 12G Series devices require the use of “single mode 1310nm compatible” fiber optic cable.
- Warning! Active fiber-optic cables emit radiation invisible to the human eye. Do not look directly at the end of an active fiber-optic cable; the FiDO 12G Series is a Class 1 Laser Product.
Warranty and Liability Information
Limited Warranty on Hardware
AJA Video Systems, Inc. (AJA Video) warrants that the hardware product, not including software components, will be free from defects in materials and workmanship for five years from the date of purchase. AJA Video provides a separate software warranty as part of the license agreement applicable to software components. If the Customer brings a valid claim under this limited warranty for a hardware product (hereafter, a “product”) during the applicable warranty period, AJA Video will, at its sole option and as the Customer’s sole remedy for breach of the above warranty, provide one of the following remedies:
- Repair or facilitate the repair the product within a reasonable period of time, free of charge for parts and labor.
- Replace the product with a direct replacement or with a product that performs substantially the same function as the original product.
- Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty.
To obtain service under this warranty, the Customer must notify AJA Video of the defect before expiration of the warranty period and make suitable arrangements for the performance of service by contacting AJA Video support through the channels set forth on the support contacts web page at https://www.aja.com/support. Except as stated, the Customer shall bear all shipping, packing, insurance and other costs, excluding parts and labor, to effectuate repair. The customer shall pack and ship the defective product to a service center designated by AJA Video, with shipping charges prepaid. AJA Video shall pay to return the product to Customer, but only if to a location within the country in which the AJA Video service center is located. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON APPLICABLE STATUTORY RIGHTS OF A CONSUMER, SO SOME OR ALL OF THE TERMS OF THIS PARAGRAPH MAY NOT APPLY TO YOU.
Agreement is intended for convenience and to meet local requirements and in the event of a dispute between the English and any non-English versions, the English version of this warranty will govern. This limited warranty gives you specific legal rights and you may have other rights that vary from jurisdiction to jurisdiction, some of which are noted above.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>