dahua DH-IPC-PFW8601N-H Bullet Network Camera User Guide

: June 4, 2024
: Dahua

Table of Contents

dahua DH-IPC-PFW8601N-H Bullet Network Camera
General
About the Manual
Important Safeguards and Warnings
- Installation Requirements
- Operation Requirements
Maintenance Requirements
Introduction
Network Configuration
Initializing the Camera
- Changing Device IP Address
- Logging in to the Web Page
Installation
- Installing the Camera
ZHEJIANG DAHUA VISION TECHNOLOGY co., LTD
Read User Manual Online (PDF format)
Download This Manual (PDF format)

dahua DH-IPC-PFW8601N-H Bullet Network Camera

General

This manual introduces the functions, configuration, general operation, and system maintenance of network camera.

Safety Instructions

The following categorized signal words with defined meanings might appear in the manual.

Signal Words	Meaning
Warning	Indicates a medium or low potential hazard which, if not

avoided, could result in slight or moderate injury.
Caution| Indicates a potential risk that, if not avoided, could result in property damage, data loss, lower performance, or unpredictable result.
Note| Provides additional information as a supplement to the text.

Revision History

Version	Revision Content	Release Date
V1.0.0	First release.	January 2022

Privacy Protection Notice

As the device user or data controller, you might collect the personal data of others such as their face, fingerprints, and license plate number. You need to be in compliance with your local privacy protection laws and regulations to protect the legitimate rights and interests of other people by implementing measures that include but are not limited: Providing clear and visible identification to inform people of the existence of the surveillance area and provide required contact information.

About the Manual

The manual is for reference only. Slight differences might be found between the manual and the product.
We are not liable for losses incurred due to operating of the product in ways that are not in compliance with the manual.
The manual will be updated according to the latest laws and regulations of related jurisdictions.
For detailed information, see the paper User Manual, use our CD-ROM, scan the QR code or visit our official website. The manual is for reference only. Slight differences might be found between the electronic version and the paper version.
All the designs and software are subject to change without prior written notice. Product updates might result in some differences appearing between the actual product and the manual. Please contact customer service for the latest program and supplementary documentation.
There might be deviations in the description of the technical data, functions and operations, or errors in the print. If there is any doubt or dispute, we reserve the right of final explanation.
Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened.
All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners.
Please visit our website, contact the supplier or customer service if any problems occur while using the device.
If there is any uncertainty or controversy, we reserve the right of final explanation.

Important Safeguards and Warnings

This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, comply with the guidelines when using it.

Transportation Requirements

Transport the device under allowed humidity and temperature conditions.
Pack the device with packaging provided by its manufacturer or packaging of the same quality before transporting it.
Do not place heavy stress on the device, violently vibrate or immerse it in liquid during transportation.

Storage Requirements

Store the device under allowed humidity and temperature conditions.
Do not place the device in a humid, dusty, extremely hot or cold site that has strong electromagnetic radiation or unstable illumination.
Do not place heavy stress on the device, violently vibrate or immerse it in liquid during storage.

Installation Requirements

warning

Strictly comply with the local electrical safety code and standards, and check whether the power supply is correct before operating the device.
Please follow the electrical requirements to power the device.
- When selecting the power adapter, the power supply must conform to the requirements of ES1 in IEC 62368-1 standard and be no higher than PS2. Please note that the power supply requirements are subject to the device label.
- We recommend using the power adapter provided with the device.
Do not connect the device to two or more kinds of power supplies, unless otherwise specified, to avoid damage to the device.
The device must be installed in a location that only professionals can access, to avoid the risk of non-professionals becoming injured from accessing the area while the device is working. Professionals must have full knowledge of the safeguards and warnings of using the device.
Do not place heavy stress on the device, violently vibrate or immerse it in liquid during installation.
An emergency disconnect device must be installed during installation and wiring at a readily accessible location for emergency power cut-off.
We recommend you use the device with a lightning protection device for stronger protection against lightning. For outdoor scenarios, strictly comply with lightning protection regulations.
Ground the function earthing portion of the device to improve its reliability (certain models are not equipped with earthing holes). The device is a class I electrical appliance. Make sure that the power supply of the device is connected to a power socket with protective earthing.
The dome cover is an optical component. Do not directly touch or wipe the surface of the cover during installation.

Operation Requirements

Warning

The cover must not be opened while the device is powered on.
Do not touch the heat dissipation component of the device to avoid the risk of getting burnt.
Use the device under allowed humidity and temperature conditions.
Do not aim the device at strong light sources (such as lamplight, and sunlight) when focusing it, to avoid reducing the lifespan of the CMOS sensor, and causing overbrightness and flickering.
When using a laser beam device, avoid exposing the device surface to laser beam radiation.
Prevent liquid from flowing into the device to avoid damage to its internal components.
Protect indoor devices from rain and dampness to avoid electric shocks and fires breaking out.
Do not block the ventilation opening near the device to avoid heat accumulation.
Protect the line cord and wires from being walked on or squeezed particularly at plugs, power sockets, and the point where they exit from the device.
Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on the lens.
The dome cover is an optical component. Do not directly touch or wipe the surface of the cover when using it.
There might be a risk of electrostatic discharge on the dome cover. Power off the device when installing the cover after the camera finishes adjustment. Do not directly touch the cover and make sure the cover is not exposed to other equipment or human bodies
Strengthen the protection of the network, device data and personal information. All necessary safety measures to ensure the network security of the device must be taken, such as using strong passwords, regularly changing your password, updating the firmware to the latest version, and isolating computer networks. For the IPC firmware of some previous versions, the ONVIF password will not be automatically synchronized after the main password of the system has been changed. You need to update the firmware or change the password manually.

Maintenance Requirements

Strictly follow the instructions to disassemble the device. Non-professionals dismantling the device can result in it leaking water or producing poor quality images. For a device that is required to be disassembled before use, make sure the seal ring is flat and in the seal groove when putting the cover back on. When you find condensed water forming on the lens or the desiccant becomes green after you disassembled the device, contact after-sales service to replace the desiccant. Desiccants might not be provided depending on the actual model.
Use the accessories suggested by the manufacturer. Installation and maintenance must be performed by qualified professionals.
Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on the lens. When it is necessary to clean the device, slightly wet a soft cloth with alcohol, and gently wipe away the dirt.
Clean the device body with a soft dry cloth. If there are any stubborn stains, clean them away with a soft cloth dipped in a neutral detergent, and then wipe the surface dry. Do not use volatile solvents such as ethyl alcohol, benzene, diluent, or abrasive detergents on the device to avoid damaging the coating and degrading the performance of the device.
The dome cover is an optical component. When it is contaminated with dust, grease, or fingerprints, use degreasing cotton moistened with a little ether or a clean soft cloth dipped in water to gently wipe it clean. An air gun is useful for blowing dust away.
It is normal for a camera made of stainless steel to develop rust on its surface after being used in a strong corrosive environment (such as the seaside, and chemical plants). Use an abrasive soft cloth moistened with a little acid solution (vinegar is recommended) to gently wipe it away. Afterward, wipe it dry.

Introduction

Cable

Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuits and water damage. For the detailed operation, see the FAQ manual.

Cable information

No.	Port name	Description

1

|

Power input

| Inputs 12 VDC power. Be sure to supply power as instructed in the manual.

Device abnormity or damage might occur if power is not supplied correctly.

2

|

Ethernet port

|

Connects to the network with a network cable.
Provides power to the device with PoE.

PoE is available on select models.

3

|

Alarm I/O

| Includes alarm signal input and output ports, the number of I/O ports might vary on different devices. For detailed information, see Table 1-2.

4

|

Audio input

| Connects to sound pickups to receive the audio signal.

Audio input is available on select models.

5

|

Audio output

| Connects to the speaker to output audio signal.

Audio output is available on select models.

Alarm information

Port	Port Name	Description

Alarm I/O

| ALARM_OUT| Outputs alarm signal to the alarm device.
ALARM_IN| Receives the switch signal of the external alarm source.
ALARM_GND| Ground connection.

Connecting Alarm Input/Output

The camera can connect to the external alarm input/output device through the digital input/output port. Alarm input/output is available on select models.

Step 1: Connect the alarm input device to the alarm input end of the I/O port. See Figure 1-2. The device collects different states of alarm input port when the input signal is idling and being grounded.

The device collects logic “1” when an input signal is connected to +3V to +5V or idling.
The device collects logic “0” when input signal is grounded.

Step 2: Connect alarm output device to the alarm output end of the I/O port. The alarm output is an open-drain output, which works in the following modes.

Mode A: Level application. The alarm outputs high and low level, and the alarm outlet is OD, which requires external pull-up resistance (10K Ohm typical) to work. The maximum external pull-up level is 12V, the maximum port current is 300 mA and the default output signal is high-level (external pull-up voltage). The default output signal switches to a lowlevel when there is alarm output (As long as the operating current is below 300 mA, the output low-level voltage is lower than 0.8V).
Mode B: Switch application. Alarm output is used to drive external circuit, the maximum voltage is 12 V and the maximum current is 300mA. If the voltage is higher than 12 V, please use an additional electric relay.

Step 3: Log in to web page, and configure alarm input and alarm output in the alarm setting.

The alarm input on the web page is corresponding to the alarm input end of the I/O port. There will be high-level and low-level alarm signals generated by the alarm input device when alarm occurs, set the input mode to “NO” (default) if the alarm input signal is logic “0” and to “NC” if the alarm input signal is logic “1”.
The alarm output on the web page is corresponding to the alarm output end of the device, which is also alarm output end of the I/O port.

Network Configuration

Device initialization and IP setting can be finished with the ConfigTool or on web page. For more information, see web operation manual.

Device initialization is available on select models, and it is required at first-time use and after device is being reset.
Device initialization is available only when the IP addresses of the device (192.168.1.108 by default) and the PC stays on the same network segment.
Plan usable network segments properly to connect the device to the network.
The following figures and interfaces are for reference only.

Initializing the Camera

Step 1: Double-click ConfigTool.exe to open the tool.
Step 2: Click Modify IP.
Step 3: Click Search Setting.

Step 4: Select the search way.

Current Segment Search (default)
- Select the Current Segment Search checkbox. Enter the username in the Username box and the password in the Password box. The system will search for the Camera accordingly.
Other Segment Search
- Select the Other Segment Search checkbox. Enter IP address in the Start IP box and End IP box respectively. Enter the user name and password. The system will search for the Camera accordingly.
If you select the Current Segment Search checkbox and the Other Segment Search checkbox together, the system searches for the Camera under both conditions.
Enter your username and password when you want to change IP, configure the system, update the Camera, restart the Camera and more.

Step 5: Click OK.
Step 6: Select one or several cameras in uninitialized status, and then click Initialize.
Step 7: Select the cameras to be initialized, and then click Initialize.

If you do not provide the linked information for a password reset, you can reset the password only through an XML file.
When initializing multiple cameras, ConfigTool initializes all cameras based on the password reset mode of the first selected camera.

Step 8: Set and confirm the password of the cameras, then enter a valid email address and then click Next.

Step 9: Select Easy4ip or select Auto-check for updates as needed. If neither, leave them unselected.
Step 10: Click OK to initialize the Camera. Click the success icon ( ) or the failure icon ( ) for the details.
Step 11: Click Finish.

Changing Device IP Address

You can change IP address of one or multiple devices at one time. This section is based on changing IP addresses in batches.
Changing IP addresses in batches is available only when the corresponding devices have the same login password.

Step 1: Follow Step1 to Step5 in “2.1 Initializing the Camera” to search devices on your network segment.

After clicking Search setting, enter the username and password, and make sure that they are the same as what you set during initialization; otherwise, there will be a wrong password notice.

Step 2: Select the devices whose IP addresses need to be modified, and then click Modify IP.

Step 3: Select Static mode, and then enter start IP, subnet mask, and gateway.

IP addresses of multiple devices will be set to the same if you select the Same IP checkbox.
If a DHCP server is available in the network, devices will automatically obtain IP addresses from the DHCP server when you select DHCP.

Step 4: Click OK.

Logging in to the Web Page

Step 1: Open the IE browser, enter the IP address of the device in the address bar and then press the Enter key. If the setup wizard is displayed, finish the settings as instructed.
Step 2: Enter the username and password in the login box, and then click Login.
Step 3: For the first-time login, click Click Here to Download Plugin, and then install the plugin as instructed. The main page is displayed when the installation is finished.

Installation

Packing List

The tool required for the installation such as an electric drill is not provided in the package.
The operation manual and related tool information are contained in the disk or the QR code, and the actual package shall prevail.