BOSCH EasyScrewDrive Cordless Screwdriver Instruction Manual

BOSCH EasyScrewDrive Cordless Screwdriver

Safety Instructions

General Power Tool Safety Warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

• Keep work area clean and well lit. Cluttered or dark areas invite acci-dents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or un-plugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of elec-tric shock.
• When operating a power tool outdoors, use an extension cord suit-able for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inat-tention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce per-sonal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and col-lection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless ac-tion can cause severe injury within a fraction of a second.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your ap-plication. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or remove the bat-tery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations differ-ent from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If li-quid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modified. Dam-aged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperat-ure. Exposure to fire or temperature above 130°C may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Safety Warnings for Screwdrivers

• Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasten-ers contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• Use suitable detectors to determine if there are hidden supply lines or contact the local utility company for assistance. Contact with elec-tric cables can cause fire and electric shock. Damaging gas lines can lead to explosion. Breaking water pipes causes property damage.
• Hold the power tool securely. When tightening and loosening screws be prepared for temporarily high torque reactions.
• Before any work on the power tool (e.g. maintenance, tool change, etc.) as well as during transport and storage, set the rotational direc-tion switch to the middle position. There is risk of injury from uninten-tionally pressing the on/off switch.
• Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.
• Always wait until the power tool has come to a complete stop before placing it down. The application tool can jam and cause you to lose con-trol of the power tool.
• Protect the power tool against heat, e.g. against con-tinuous intense sunlight, fire, water, and moisture. There is a risk of explosion.

Safety instructions for power supply

• This power supply is not intended for use by children or persons with physical, sensory or mental limitations or a lack of experience or knowledge. This power supply can be used by children aged 8 or older and by persons who have physical, sensory or mental limita-tions or a lack of experience or knowledge if a person responsible for their safety supervises them or has instructed them in the safe oper-ation of the power supply and they understand the associated dangers. Otherwise, there is a risk of operating errors and injuries.
• Do not expose the power supply to rain or wet conditions. Water entering the power supply will increase the risk of electric shock.
• Keep the power supply clean. Dirt poses a risk of electric shock.
• Always check the power supply before use. Stop using the power supply if you discover any damage. Do not open the power supply yourself, and have it repaired only by a qualified specialist using only original replacement parts.
• Damaged power supplies increase the risk of electric shock.

Product Description and Specifications

• Read all the safety and general instructions. Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury.
• Please observe the illustrations at the beginning of this operating manual.

Intended Use
The power tool is intended for screwing in and loosening screws.

Product Features
The numbering of the product features refers to the diagram of the power tool on the graphics page.

1. Screwdriver bit
2. Tool holder
3. Work light
4. Battery charge indicator
5. Rotational direction switch
6. Port for charging cable
7. On/off switch
8. Handle (insulated gripping surface)
9. Charging cable
10. Power adaptor

Technical Data

Noise/Vibration Information
Noise emission values determined according to EN 62841-2-2.

Typically, the A-weighted sound pressure level of the power tool is less than 70 dB(A). The noise level when working can exceed the volume stated.

Wear hearing protection!
Vibration total values ah (triax vector sum) and uncertainty K determined ac- cording to 62841-2-2

• Screwdriving: ah < 2.5 m/s2, K = 1.5 m/s2.
• The vibration level and noise emission value given in these instructions have been measured in accordance with a standardised measuring procedure and may be used to compare power tools. They may also be used for a prelimin-ary estimation of vibration and noise emissions.
• The stated vibration level and noise emission value represent the main ap-plications of the power tool. However, if the power tool is used for other ap-plications, with different application tools or is poorly maintained, the vibra-tion level and noise emission value may differ. This may significantly in-crease the vibration and noise emissions over the total working period.
• To estimate vibration and noise emissions accurately, the times when the tool is switched off or when it is running but not actually being used should also be taken into account. This may significantly reduce vibration and noise emissions over the total working period.
• Implement additional safety measures to protect the operator from the ef-fects of vibration, such as servicing the power tool and application tools, keeping their hands warm, and organising workflows correctly.

Assembly

Before any work on the power tool (e.g. maintenance, tool change, etc.) as well as during transport and storage, set the rotational direc-tion switch to the middle position. There is risk of injury from uninten-tionally pressing the on/off switch.

Battery charging (see figure A)

Use only the power adaptors listed in the technical data. Only these power adaptors are matched to the lithium-ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure the maximum per-formance of the battery, use the power adaptor to fully charge the battery before first use.

• The lithium-ion battery can be charged at any time without reducing its ser-vice life. Interrupting the charging process does not damage the battery.
• The lithium-ion battery is protected against deep discharge by the “Elec-tronic Cell Protection (ECP)”. When the battery is discharged, the power tool is switched off by means of a protective circuit: The application tool stops moving.
• Do not continue to press the On/Off switch after the power tool has automatically switched off. The battery can be damaged.
• If the battery charge indicator (4) lights up red when you press the On/Off switch (7) half way in, the remaining battery capacity is less than 30% and the battery should be charged.
• To charge the battery, plug the charging cable (9) into the port (6) on the bottom of the handle and into the power supply (10). Plug the power supply (10) into the plug socket.
• The charging process is interrupted when the on/off switch (7) is fully pressed.
• The battery charge indicator (4) indicates the charging progress. The indic-ator flashes green during the charging process. When the battery is fully charged, the battery charge indicator (4) is continuously lit green.
• During the charging process, the handle of the power tool will become warm. This is normal. If you are not planning to use the power tool again soon, disconnect the power adaptor from the mains. The power tool cannot be used during the charging process. It is not defective if it does not work during the charging process. Follow the instructions on correct disposal.
• Protect the power adaptor against moisture.

Changing the tool (see figure B)

• Do not use two-sided screwdriver bits that are longer than 25 mm. Insert the screwdriver bit (1) directly into the tool holder (2).

Operation

Starting Operation

Setting the rotational direction
The rotational direction switch (5) is used to change the rotational direction of the power tool. However, this is not possible while the on/off switch (7) is being pressed.

• Do not use the rotational direction switch (5) when the power tool is in operation, as this may damage it.
• Clockwise rotation : To drive in screws, slide the rotational direction switch (5) forward to the stop.
• Anti-clockwise rotation: To loosen or unscrew screws, slide the rotational direction switch (5) backwards.

Switching on/off

• To start the power tool, press and hold the on/off switch (7).
• The work light (3) lights up when the On/Off switch (7) is lightly or fully pressed, allowing the work area to be illuminated in poor lighting conditions. To switch off the power tool, release the on/off switch (7).
• Fully automatic spindle lock (Auto-Lock)
• The drill spindle, and therefore the tool holder, are locked when the on/off switch (7) is not pressed.
• This allows screws to be driven in even when the battery is discharged and enables the power tool to be used as a screwdriver.
• If the drill spindle is blocked, do not press the on/off switch (7) for longer than 15 seconds. Otherwise, the power tool may become dam-aged.

Practical advice
Only apply the power tool to the screw/nut when the tool is switched off. Rotating tool inserts can slip off.

Maintenance and Service

Maintenance and Cleaning

• To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean.
• If the battery is no longer working, please contact an authorised after-sales service agent for Bosch power tools.
• In order to avoid safety hazards, if the power supply cord needs to be re-placed, this must be done by Bosch or by an after-sales service centre that is authorised to repair Bosch power tools.
• After-Sales Service and Application Service
• Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com
• The Bosch product use advice team will be happy to help you with any ques-tions about our products and their accessories.
• In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Great Britain

• Robert Bosch Ltd. (B.S.C.)
• P.O. Box 98
• Broadwater Park
• North Orbital Road
• Denham Uxbridge
• UB 9 5HJ
• At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
• Tel. Service : (0344) 7360109
• E-Mail: boschservicecentre@bosch.com

You can find further service addresses at:www.bosch- pt.com/serviceaddresses

Transport

• The contained lithium-ion batteries are subject to the Dangerous Goods Le-gislation requirements. The batteries are suitable for road-transport by the user without further restrictions.
• When shipping by third parties (e.g.: by air transport or forwarding agency), special requirements on packaging and labelling must be observed. For pre-paration of the item being shipped, consulting an expert for hazardous ma-terial is required.

Disposal

• Power tools, rechargeable batteries, accessories and packaging should be sorted for environmental-friendly recycling.

• Do not dispose of power tools and batteries/rechargeable batteries into household waste!

Only for EU countries

• According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, power tools that are no longer usable, and, according to the Directive 2006/66/EC, defective or drained batteries must be collected separately and disposed of in an environmentally correct manner.
• If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for United Kingdom
According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environ-mentally friendly manner.

Battery packs/batteries

Li-ion
Please observe the notes in the section on transport (see “Transport”, page 30).
Integrated batteries may only be removed for disposal by qualified personnel. Opening the housing shell can destroy the power tool.
Before you can remove the battery from the power tool, you will need to use the power tool until the battery is completely discharged. Unscrew the screws on the housing and remove the housing shell in order to remove the battery. To prevent a short circuit, disconnect the connectors on the battery one at a time and then isolate the poles. Even when fully discharged, the bat-tery still contains a residual capacity which can be released in case of a short circuit.

• e EU Declaration of Con- We declare under our sole responsibility that n format the stated products comply with all applicable
• Cordless Article hum  provisions of the directives and regulations screwdri- ber  listed below and are in conformity with the  veer following standards. Technical file at: *

Easy- Screw- Drive

3 603 JA8 100

• 2006/42/EC          EN 62841-1:2015
• 2014/30/EU          EN 62841-2-2:2014
• 2011/65/EU          EN 55014-1:2017+
• A11:2020

| |

• EN 55014-2:2015
• EN IEC 63000:2018

---|---|---

• • Robert Bosch Power Tools GmbH (PT/ECS)

• 70538 Stuttgart GERMANY

• Henk Becker     Helmut Heinemann Chairman of  Head of Product Certify

• Executive Manage- cantonment

• Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY

• Stuttgart, 29.09.2022

Declaration of Conformity

Cordless Drill/Driver  Article number
EasyScrewDrive 3 603 JA8 100
We declare under our sole responsibility that the stated products comply with all applicable provisions of the regulations listed below and are in conformity with the following standards.

• Technical file at: Robert Bosch Ltd. (PT/SOP-GB), Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom
• The Supply of Machinery (Safety) Regulations 2008
• The Electromagnetic Compatibility Regulations 2016
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
• EN 62841-1:2015
• EN 62841-2-2:2014
• EN 55014-1:2017+
• A11:2020
• EN 55014-2:2015
• EN IEC 63000:2018

Vonjy Rajakoba
Managing Director – Bosch UK

• Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany represented (in terms of the above regulations) by
• Robert Bosch Limited, Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom

Martin Sibley

• Head of Sales Operations and Aftersales

Robert Bosch Ltd. Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom, as authorized representative acting on behalf of Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany

• Place of issue : Uxbridge
• Date of issue : 30/09/2022

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>