Syutong AM0306LRF Thermal Imaging Sights User Guide

Syutong AM0306LRF Thermal Imaging Sights User Guide

Shenzhen Shi Yutong Technology Co ., LTD

In The Box

• Thermal Imaging Sight
• Manual
• Type-C Cable
• 5V 2A Adapter
• Battery
• Mount (with screws and hex-nut wrenches)

Quick Start

Power On and Image Settings

• Hold the power (ON/OFF) button (11) for 3 seconds to power on.
• Rotate the dioptre adjustment ring (7) to get a clear image of the icons on the display.
• Rotate the lens focusing ring (2) to get a clear image of the observed object.
• Press the navigation UP button (4) to select the operating modes (White Hot, Sky Mode, Black Hot,Red Hot, Fusion).
• Press the navigation DOWN button (6) to select digital magnification (Ix, 2x, 4x, 8x).
• Press the MENU button (5) to enter the menu to select the appropriate parameter.
• Hold the power (ON/OFF) button (11) for 3 seconds to power off. The LED indicator will be turned off after the device is powered off.

Buttons

Button Legend

Menu Functions

Installing The Battery

Please use lithium chargeable 3.7V flat battery 18650. Remove battery compartment cap and make sure setting the positive polar towards to the direction inward. Put the cap back and screw it until tight. ( Fail to do so may result in restarting!).

Using The Integrated Laser Rangefinder

• Hold the power (ON/OFF) button (11) for 3 seconds to power on the device.
• Hold the navigation DOWN button (6) for 3 seconds to activate the laser rangefinder.
• The rangefinder indicator (a small box) will appear at the center of the display.
• Point the range finding indicator at an object to measure the distance (the distance will be displayed at the top right corner of the display).

Installation Of Mount

• Attach the mount to the base of the scope using a hex-nut wrench and screws.
• The mounting holes in the base of the scope enable the mount to be installed in one of the multiple positions. The choice of the mounting position helps the user to ensure the correct eye relief depending on the device type.
• The scope is ready to be installed on a device and to be zeroed.
• Before using the device, please follow instructions in the section “Reticle Adjustment (Zeroing)”.

APP Connection

AM-03LRF

Notice!

Operating Instructions For Accessories

Power Adapter
Used only to charge batteries equal to or below 5V/2A.

Red Laser Pointer Adjustment
Hold the MENU button to turn on/off the red laser pointer. Adjust the position of the red laser pointer by using an inner hexagon wrench.

Connect to a Computer
Turn off the device and connect to the computer with a Type-C cable. Hold the power button to turn on the device. The computer will read the memory card of the device.

FCC Warning Statement: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>