Industrial Scientific 9.0-99999 Intelligent Digital Tachometer User Manual

June 14, 2024
INDUSTRIAL SCIENTIFIC

Industrial Scientific logo Inteiligent Digital Tacnometer
User Manual
V1.3.2

LCD Display

Industrial Scientific 9.0 99999 Intelligent Digital Tachometer -
Display

  1. Measurement reminder symbol
  2. USB connection prompt
  3. Memory mark
  4. Value lock
  5. Maximum and minimum
  6. Battery power reminder
  7. Numerical display area
  8. Unit display area
  9. CONTACT symbol
  10. PHOTO symbol

Product Schematic Diagram

Industrial Scientific 9.0 99999 Intelligent Digital Tachometer - Display
1

Contact speed accessories

  1. Contact line speed accessories (replaceable)

  2. Accessory connector
    (P1 can be removed)

  3. LCD display area

  4. /TEST key

  5. /UNIT key

  6. MEM key

  7. Battery compartment

Battery Installation Instructions

  1. Insert the battery according to the positive and negative instructions inside the battery compartment.
  2. After inserting the battery, please close the battery cover.
  3. When the instrument is not used for a long time, be sure to remove the battery and place it properly.

Description of Key Functions

3.1 /TEST Key

  1. Press the button to turn on the instrument.
    Note: The instrument will automatically shut down if there is no key operation for about 15 seconds by default.

  2. Press and hold, the instrument starts to measure.

  3. After the measurement is released, the instrument will lock the measured value, and the value will not change after being locked.

3,2 /UNIT Key

  1. Short press to switch the unit RPM{revolution/minute), Hz(Hertz), m/min({meter/minute) and ft/min(feet per minute).
  2. Long press to turn on or off the screen backlight.

3.3 MEM Key

  1. View the currently measured lock value (HOLD), maximum value (MAX) and minimum value (MIN).
  2. View the locked value (MEM HOLD), maximum value (MEM MAX) and minimum value (MEM MIN) of the last measurement before the instrument is turned off.

Measurement Procedure

4.1 Photoelectric Soeed Measurement (Only applicable to some models)

  1. Paste a reflective mark on the object to be measured.
  2. After turned on, short press ****/UNIT” key to choose “P-RPM” (If the contact accessories have been installed, please remove the accessories and accessory connectors).
  3. Press and hold the /TEST” key, at the same time, make the red laser and the reflection mark in a straight line; after the data is stable, release the /TEST™ key, the instrument locks the current data.
  4. Press the “MEM” key to view the lock data, maximum data and minimum data.

Note: a. When the rotation speed is low, a few more reflective marks can be evenly affixed on the rotating surface. Note that the non-reflective area is larger than the reflective area (The final rotation speed value is equal to the value displayed by the instrument divided by the number of reflective marks).
b. If the rotating surface is obviously reflective, please apply black paint or black tape before attaching the reflective marker.
4,2 Light Source Flicker Frequency (Only applicable to some models)

  1. After turning on the machine, short press the /UNIT” key to select “P-Hz” (If contact accessories have been installed, please remove the accessories and their connectors).
  2. Align the measuring window of the instrument with the light source to be measured.
  3. Press and hold the /TEST” key, and release the key after the value is Stable, the instrument locks the current cata.
  4. Press the “MEM” key to view the locked data, maximum data and minimum data.

4,3 Contact Soeed Measurement (Only applicable to some models)

  1. Install suitable contact speed accessories.
  2. After starting up, short press the /UNIT” key to select “C-RPM”.
  3. Clase the accessory to the object to be measured and make it rotate synchronously with the object to be measured.
  4. Press and hold the /TEST” key, and release the key after the value is Stable, the instrument will lock the current cata.
  5. Press the “MEM” key to view the locked data, maximum data and minimum data.

4.4 Contact Line Speed Measurement (Only applicable to some models)

  1. Install the contact line soeed accessories.
  2. After starting up, short press the /UNIT” key to select “C-m/min” or “C-ft/min”.
  3. Close the accessory to the object to be measured and make it rotate synchronously with the object to be measured.
  4. Press and hold the /TEST” key, and release the key after the value is Stable, the instrument will lock the current value.
  5. Press the “MEM” key to view the locked value, maximum value and minimum value.

Technical Parameters

Measurement parameters| Contact line speed| Contact speed| Photoelectric speed| Light source flicker frequency
---|---|---|---|---
Measuring range| 0.10∼1999.9m/min
0.4∼6560ft/min| 1.0-19999RPM| 9.0-99999RPM| 0.1-6000.0Hz
Accuracy| ±(0.05% of reading +1)| | ± (0.02% of reading)
Resolution| 0.01nVmin (0.10∼99.99m/min) 0.1m/min (above 100m/min) 0.1ft/min (0.4∼999.9f /min) 1ft/min (above 1000ft/min)| 0.1RPM (1 0∼999 9RPM) 1RPM (above 1000RPM)| 0.1RPM (9.0∼999.9RPM) 1RPM (above 1000RPM)| 0.1Hz
Unit| RPM, Hz, nVmin, ft/min
Effective distance| No| 50∼500mm
Range selection| Auto range
Display| Segment LCD screen with backlight
Protection level| IP43
Power supply| 3 pcs of 1.5V AAA alkaline batteries/3 pcs of 1.2V AAA rechargeable batteries
Host size| 1906833mm
Shell material| ABS
Host weight| About 149g (without batteries)

Industrial Scientific logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals