FLARING FC550D Plasma Cutter Instruction Manual
- June 14, 2024
- FLARING
Table of Contents
FLARING FC550D Plasma Cutter
Version
Due to product version upgrades or other reasons, the contents of this
document are not regularly updated. Unless otherwise agreed, this document is
intended as a guide only and all statements, information and recommendations
in this document do not constitute any guarantee, expressed or implied. The
pictures in this document are for reference only. If the picture is different
from the real one, then use the pictures for guidance only.
Product brief introduction
Summarize
Inverter Technology
| This device uses single-tube IGBT inverter technology (the inverter frequency range is from 25-50KHz) to convert 50/60Hz alternating current (AC) to direct current (DC) and then to high
frequency and lower voltage rectification. The resulting pulse width modulation (PWM) output can be used for the high-power DC power supply, Due to the switching power inverter technology adopted, the weight of the welder has been significantly decreased and the conversion efficiency of the whole
machine is increased by more than 30%.
---|---
Wide Voltage| Our cutting machine is equipped with a power supply voltage
compensation device,The power supply voltage will work when the rated voltage
is within 15% of requirements. When using extension cords, in order to reduce
voltage drop, use a heavy-duty extension cord (10 or 12AWG or
greater) or use the recommended configuration length.
Easy to Use| A piloting arc system can strike an arc easily with the principle of high-frequency oscillation.It has functions
that it can supply gas ahead and turn off gas delays.High-frequency arc starting
Widely Used| It is suitable for cutting stainless,Steel, alloy steel, mild steel, copper and other color metal
materials.
Superior
Performance
| 1. Stabilizing 2.Reliability 3. Lightness 4. Energy-saving and no noise 5.High cutting speed 6.Cutting
smoothly and no polish demands
Attention| Plasma cutter, the consumables are not on correctly, they are usually missing the white spacer. Air regular not in it the correct direction(this will not give it enough flow).
Air leaking from the hose connections. Customers don’t know they have to touch the metal to start
the arc.
Technical parameters
TYPE | FC550D |
---|---|
Input power voltage | AC120V,50/60Hz |
Rated input current | 39A |
Rated power capacity | 4.5KVA |
Current adjustment range | 15A-35A |
Cutting thickness
| Carbon Steel≤12.0mm(1/2in) Stainless Steel≤12.0mm(1/2in) Aluminum≤5.0mm(13/64in)
Copper≤4.0mm(5/32in)
| Carbon Steel≤16.0mm(5/8in) Stainless Steel≤16.0mm(5/8in) Aluminum≤6.0mm(15/64in)
Copper≤5.0mm(13/64in)
Voltage adjustment range| 86V-102V
No-load voltage| 325V
Rated duty cycle| 20%
Efficiency| 75%
Power factor| 0.85
Protection class| IP21S
Insulation class| H
Size| 360120285mm (14.24.711.2in)
Weight| 4.8Kg (10.58lb)
Accessories list
Installation instruction
Installation of Air Regulator
- Wrap the copper gas nozzle around the sealing tape and tighten it on the IN and OUT ends;
- Wrap the meter head with the sealing tape and tighten it on the meter head installation position;
- Fix the connecting frame to the installation position of the pressure-reducing valve behind the welder as shown in the figure;
- Unscrew the rubber nut and fix the pressure-reducing valve on the connecting frame as shown in the figure;
- Turn on the air valve switch, lift up the pressure regulating knob, adjust the air pressure to the specified air pressure (turn to “+” to increase the air pressure, and to “-” to decrease the air pressure), then Press down the pressure regulating knob;
- The scale position of the meter, suggests the indicated position is 60-70PSI(about 0.4Mpa) air pressure. When there is too much water in the filter cylinder, the drain valve should be opened to drain the water.
Air compressor connect to plasma cutter
Plasma Cutter Torch connect to machine
Cutting Torch explosive chart
- Outside nozzle,
- Extend tip,
- Diffuser,
- Electrode.
These are wear parts, among which the extend tip and electrode are very easy to wear, please keep it
Operating instructions
Operation panel interface
1| Current display meter,Display preset current and actual current during operation。The maximum output current is
55A when the 240V voltage is input, and 35A when the 120V voltage is input.
---|---
2
| Power light
When this light is on, it means that the power supply is normal.This machine can accept 120V or 240V power supply.
3
| Over current or overheat protection light
When the cutting load is overloaded and the output current of the machine is too large, the internal temperature of the machine is too high, and the machine fault light will be on. This is normal. The machine can recover after the heat dissipation becomes normal. Please restart the power supply; When damaged, the fault light will be on, in this case, the machine is abnormal and needs maintenance, please contact the supplier.
4| Current adjust knob
5| Recommended selection range of air pressure: when 120V is input, it is
recommended to adjust the input air
pressure at 30-50PSI; When 240V is input, it is recommended to adjust the input air pressure at 30-70PSI.
Cutting Operation instruction
On display
After opening the power supply, the power light is lit, the current meter
displays the preset current.
Preparation
Input cable connection
- Every machine has been disposed of a power cable which must be connected to a coordinated voltage class in compliance with to input voltage of cutting machine. If the cutting machine whose power voltage is 230V is connected wrong to AC 400V, that will cause components of the inter-machine are burn up.
- Make sure the power cable is connected to the power switch reliably and prevent it from oxidizing. Make sure the power voltage is inside the wave range.
Connect Air compressor
- Make sure tube of pressed air is connected to the copper connector by a high-pressure rubber tube.
- Connect one end of the trachea to the gas in of the machine and the other end to the air compressor.(Refer to 2.2)
Output cable connection
- Earth cable is connected to the positive terminal of the front panel then tighten it.
- Make sure the copper screw of another end of the torch is connected to the gas-electrify integration terminal then tighten them clockwise relation (prevent from leaking gas). (Refer to 2.3)
Operation
- Open the power switch; make sure the power switch is in the “on” position. The screen will show the current volume.
- Adjust the gas pressure and make it is adequate to the machine, open the valve of pressed air.
- Make sure the cutting current is adequate to machine according to the thickness of the cutting piece.
- Press the control knob of the torch, the electromagnetic valve is starting, it can be heard and the burner of the torch should flow out gas (The burner of low-frequency cutting machines or pilote-arc cutters should spurt fire)
- It is 1mm from the copper tip to the workpiece (if it is an arc-supporting cutter.), It is 3-5mm from copper tip to work piecepress(if it is a burner of low frequency cutting machines or pilote-arc cutter ).knob of the torch and burns and strike arc, sparks of HF arc striking will be diminished immediately. The user can begin to cut.
Adjust air pressure and Current
1
| Input 240V| 20Amps| 35Amps| 40Amps| 45Amps| 55Amps
---|---|---|---|---|---|---
Air pressure
| 30-70(PSI)
0.21-0.49(MPa)
| 30-70(PSI)
0.21-0.49(MPa)
| 30-70(PSI)
0.21-0.49(MPa)
| 30-70(PSI)
0.21-0.49(MPa)
| 30-70(PSI)
0.21-0.49(MPa)
Thickness (Fe)| 5mm(13/64in)| 8mm(5/16in)| 10mm(25/64in)| 12mm(1/2in)|
16mm(5/8in)
Thickness (Ss)| 5mm(13/64in)| 8mm(5/16in)| 10mm(25/64in)| 12mm(1/2in)|
16mm(5/8in)
Thickness (Al)| 1mm(3/64in)| 3mm(1/8in)| 4mm(5/32in)| 5mm(13/64in)|
6mm(15/64in)
Thickness (Cu)| | 2mm(5/64in)| 3mm(1/8in)| 4mm(5/32in)| 5mm(13/64in)
2
| Input 120V| 20Amps| 30Amps| 35Amps| |
Air pressure
| 30-50(PSI)
0.21-0.35(MPa)
| 30-50(PSI)
0.21-0.35(MPa)
| 30-50(PSI)
0.21-0.35(MPa)
| |
Thickness (Fe)| 5mm(13/64in)| 8mm(5/16in)| 12mm(1/2in)| |
Thickness (Ss)| 5mm(13/64in)| 8mm(5/16in)| 12mm(1/2in)| |
Thickness (Al)| 1mm(3/64in)| 2mm(5/64in)| 3mm(1/8in)| |
Thickness (Cu)| | 1mm(3/64in)| 2mm(5/64in)| |
Start Cutting
Edge cutting
- Keep the torch vertical at the edge of the workpiece. Keep your wrist steady and ready to start cutting
- Pull the trigger to start the arc , The cutting arc will initiate when the torch tip is close enough to the work Piece. Start cutting on the edge until the Arc has cut completely through.
- fast speed will lead to incomplete cutting, and arc blowback is easy to damage the device. Too slow speed will lead to excessive scum and cutting gap.
- Hold the torch at an angle to the workpiece, pull the trigger to start the arc, and slowly rotate it to an upright position.
- Pull the trigger to start the arc , The cutting arc will initiate when the torch tip is close enough to the work Piece. Start cutting on the edge until the Arc has cut completely through.
- When the piece is complete, Control the cutting speed and adjust the angle and position of the cutting torch to continue the cutting operation. Too fast speed will lead to incomplete cutting, and arc blowback is easy to damage the device. Too slow speed will lead to excessive scum and cutting the gap.
Cutting performance
1| Amperage| Standard rule of thumb is the thicker the material the more amperage required. On thick material, set the machine to full output and vary your travel speed. On thinner material, you need to turn down the amperage and change to a lower-amperage tip to maintain a narrow kerf. The kerf is the width of the
cut material that is removed during cutting.
---|---|---
2| Speed| Amperage and speed are critical to producing a good
quality cut. visually follow the arc that is coming from the bottom of the
cut. The arc should exit the material at a slight angle away from the
direction of travel. If it’s going straight down, that means the speed is too
slow, and IT will have an unnecessary buildup of dross or slag. If the speed
is too fast, it will start spraying back onto the surface of the materia
without cutting the workpiece completely. Because the arc trails at an angle,
at the end of a
cut, slow your cutting speed and angle the torch in to cut through the last bit of metal.
3| Direction| It is easier to pull the torch towards you than push it. The plasma stream swirls as it exits the tip, biting one side and finishing off on the other leaving a bevelled edge and a straight edge. The bevel cut effect is more noticeable on thicker material and needs to taken into consideration before starting your cut as
you want the straight side of the cut to be on the finished piece you keep.
4| Torch tip height &
position
| The distance and position of the plasma torch cutting tip has an affect on the quality of the cut and the extent of the bevel of the cut. The easiest way to reduce bevel is by cutting at the proper speed and
height for the material and amperage that is being cut.
5| Tip size and condition| The tip orifices focus the plasma stream to the work piece. It is important to use the correct size tip for the amperage being used,for example a tip with a 3/64″ orifice is good for 0-40 amps whereas a 1/16″ orifice is better for 40-80 amps.
The low-amp tip has a smaller orifice which maintains a narrow plasma stream at lower settings for use on thin-gauge material. Using a 25 amp tip at an 60 amp setting will blow out and distort the tip orifice and require replacement.
Conversely, using an 80-amp tip on the lower settings will not allow you to focus the plasma stream as
well and creates a wide kerf.The condition of the tip orifice is critical to the quality of the cut result, a worn or damaged tip orifice will produce a distorted plasma stream resulting in poor cut quality.
6| Electrode condition| A fixed gap is established between the electrode and the inside of the cutting tip. Electrons arc across the gap, ionizing and superheating the air creating the plasma stream. The electrode contains an insert in the end made of a highly conductive material called hafnium. This insert erodes with use and
develops a pit in the end of the electrode, when the pit becomes too much poor quality cuts will result
and necessitate the replacement of the electrode. | ||
---|---|---|
7 | Air quality, | Compressors take in air at atmospheric pressure |
increase the pressure and store it in a tank.
| Air| Moisture that forms in airlines has a tendency to condense into
larger drops when the air pressure
| pressure| decreases as it enters the plasma torch. When these
droplets enter into the high temperatures in
| and| the plenum of the torch, they immediately break down into oxygen
and hydrogen, which alters the
| volume| normal chemical content of air in the torch. These elements
will then dramatically change the plasma
| | arc which causes the torch consumable parts to wear very quickly, alters
the shape of the nozzle
| | orifice, dramatically affecting cut quality in terms of edge squareness,
dross formation, and edge
| | smoothness.Air pressure, flow rate and air quality are critical to
quality plasma cutting and consumable
| | life span.Usually air pressure is preset at 60 psi . The volume capacity
of your compressor is important,
| | If you are doing a lot of cutting, cutting thick plate (same air
consumption but slower cut speeds =
| | longer cut time) then choose a compressor at 1.5 to 2 times the plasma
system requirement.
Hand torch cutting Show
Torch tip height & position
- The correct torch height and right angle shall be consistent with the minimum slope and equal slope of the material, so as to ensure good cutting effect and prolong the service life of consumables.
- Torch angled to the material’s unequal bevel, one side may be excessively beveled.
- Torch height is too high, the plasma stream may not cut all the way through the material.
- Torch height is too low. The tip may contact the workpiece and short out or damage the tip.
Speed and Amperage
- When cutting, select the appropriate current and pushing speed according to the material and thickness of the workpiece to ensure that the spark are exiting from the bottom of the workpiece
- If the spark comes out from the top of the workpiece, it means that the workpiece has not been completely cut, because the torch moves too fast or the current is set too low.
- If the spark passes vertically through the workpiece, it indicates that the workpiece has been completely cut off and the torch is cutting air because the torch moves too slowly or the current setting is too large
Troubleshooting and fault-finding
Notes: The following operations must be performed by qualified electricians with valid certifications. Before maintenance, you are suggested to contact local distributor to verify qualification.
Faults | Resolvable Methods |
---|
The switch indicator is on, the fan is not working, and the control knob is
out of work.| Ø Overvoltage protection is working. Close the machine then Open
it again after several minutes.
The switch indicator is lit, the fan is working.
press the control knob of the torch, there is no HF
arc-striking sound and the electromagnetic valve is not working.
| Ø Check if the torch is an open circuit.
Ø Check if the control knob of the torch is damaged.
Ø Part of the assistant power of the top board is damaged and there is no DC 24V output.
The switch indicator is lit, the fan is working.
press the control knob of the torch, there is no HF arc striking
sound, and inter red diode is lit.
| Ø Check if the MOS or IGBT of the top board is damaged (driver mold is damaged).
Ø Rising transformer of the bottom board is damaged.
Ø Control mold is damaged.
The switch indicator is lit, the fan and electromagnetic valve are working, there is no sound of HF arc-striking and the interred diode is not lit.| There is some trouble in a part of arc-striking, such as:
Ø It is too far between the discharge tip or there is adhesion in the discharge tip.
Ø The Primary coil of the arc-striking transformer is damaged or in poor contact.
Ø Check if four times voltage rectifier diode is stricken.
Ø Check if HF electric capacity 102/10KV is leaking.
Ø Relay is damaged.
Other of the machine is normal, but the arc is not stricken when it is be operating.| Ø Input voltage is too low.
Ø Pressure of the air compressor is too high or too low .
Even the machine comes up with abnormal phenomena such as cutting unable, arc unstable or bad welding effect, it is still early to judge whether there is a malfunction in the machine. The above-mentioned abnormal phenomenon may be caused by some reasons.
For example
tight parts loosen, forgetting to switch on, wrong set up, cable broken gas
rubber pipe cracked, etc. Therefore, please test and inspect these factors
before delivering it back to the factory because a large number of troubles
may be easily solved probably.
Daily maintenance and checking
Daily maintenance
- Remove dust regularly with dry compressed air. If the cutting machine is used in surroundings with heavy smoke and polluted air, it is necessary to remove dust at least one time one month.
- The pressure of compressed air shall fall to the required level to prevent damage to small components in the machine.
- Examine inside electric joints and ensure perfect contact (Especially plugs and sockets). Fasten the loosing joints. In case of oxidation, remove the oxide film with sandpaper and connect again.
- Prevent water from entering into the machine and prevent the machine from getting moist. If any, blow and dry. Measure the insulation with a megohmmeter to make sure it is qualified to use.
- If the cutting machine is not used for a long time, pack the machine in its original package and store in dry surroundings.
WARNING
All the maintenance and testing must be carried out when the power supply
is totally cut off. Please make sure the power is off before opening the
closure.
Daily checking
POWER SUPPLY
Position| Checking keys| Remarks
Control panel
| Ø Operation,conversion and installation of the switch
Ø Check the state of the power indicator light
| Lead to unstable arc and wire
sending
Cooling fan
| ****
Ø Check if the fan state and the sound is normal or not
| Clean the residue and check the
reason and solve it
Power part
| Ø Check if there is abnormal liberation and sound when the power is on
Ø Check if there is smell when the power is on
Ø Whether the outside color change or get warm
|
Outer parts
| Ø The connector is loosened
Ø Whether the outer shell or other connected parts are loosen
|
CABLE
Position| Checking keys| Remarks
Output cable
| Ø Wearing out of the cable-insulated material
Ø Cable connecting head naked (insulation damage), or loosen (the end of power supply, and cable of main material
connecting point)
| ****
Ø For life security and stable cutting, adopt a suitable method to check according to the working place
Ø Simple check daily
Ø Careful and in-depth check on fixed period
Input cable
| Ø If the connection between the plug and the power socket is firm
Ø If the power input end cable fixed
Ø If the input cable is worn out and bares the conductor
| ****
In case of leakage and to ensure safety, please do perform daily checking
Earth cable
| If the earth cable that connects the main part is
broken and connects tightly
CUTTING TORCH
Position| Checking keys| Remarks
Switch
| Ø Press the torch switch, no gas comes out.| Check switch.
Ø Press the torch switch, arc cannot be started.| ****
Check switch.
Extend tip, Electrode
| ****
Ø Cutting power is reduced.
| ****
Replace.
Cutting problems and resolution
The phenomenon listed below may happen due to relevant accessories used,
cutting material, surroundings and power supply. Please improve the
surroundings and avoid these problems.
Arc starting difficulty. Arc interruption happens easily:
- Examine whether the grounding wire clamp contacts with the work pieces well.
- Examine whether each joint has improper contact.
The output current fails to reach the rated value:
The deviation of power voltage from the rated value may cause the output
current does no accord with the adjusted value. When the power voltage is
lower than the rated value, the maximum output current may be lower than the
rated value.
The current can not keep stable during operation:
This situation may relate to the following factors:
- The voltage of electric power network changes;
- Serious interference from electric power network or other electric facilities.
Attention
The safety notes listed in this manual is to ensure correct use of the machine
and to keep you and other people from being hurt. The design and manufacture
of cutting machine consider safety. Please refer to the safety warning listed
in the manual to avoid accidents. Different damage would be caused by wrong
operation of the equipment as follows. Please read the user manual carefully
to reduce such damage.
Cutting environment and safety
Working surrounding
- Cutting should be carried out in dry surroundings. The air humidity level should not be higher than 90%.
- The temperature should be between -10°C to 40°C.
- Don’t use the cutting machines in sunshine or rain. Keep it off the water.
- Don’t use the machines in places of dust or corrosive air.
- Cutter machines should not be carried out in places with quick airflow.
Safety norms
Protection circuits of over-voltage, over-current, and over-heat circuits are
designed in the cutting machines. It will stop working automatically when the
input voltage, output current or internal temperature exceeds the rated value.
But if the machines are excessively used, such as with input voltage higher
than the rated, the machine might be damaged. Please pay close attention to
the following matters.
Keep good ventilation!!
The cutting machines work with high cutting voltage. Nature air flow can’t
reach the requirement of heat dissipation. So the fans are installed as
cooling systems to ensure stable performance. Make sure the ventilation
windows are not covered or blocked. The distance between the machines and
things around should not be less than 0.3m. Good ventilation is good for
cutting performance and operational life.
Never overload!
Check the maximum rated current (according to the Duty Cycle chosen). Make
sure the cutting current is never higher than the rated value. Over-current
running will obviously shorten the operation life, even damage the machine.
Never over voltage!
The Input Voltage can be found in the Technical data diagram. The auto-
compensation function will keep the cutting current in the rated range. If the
input voltage exceeds the permissible value, the machine will be damaged.
Users should take protective measures in advance to avoid it.
Make sure Earth is connected before the operation
On the rear panel of the cutting machine, a screw for earth connecting would
be found. It must be ground-connected with a cable whose section is bigger
than 6mm2 before an operation, to avoid accidents caused by static or
electricity leak.
Symbol definition:
The safety notes listed in this manual is to ensure correct use of the machine
and to keep you and other people from being hurt. The design and manufacture
of cutting machines consider safety. Please refer to the safety warning listed
in the manual to avoid accidents. Different damage would be caused by wrong
operation of the equipment as follows. Please read the user manual carefully
to reduce such damage. This Manual contains symbols as blow, please refer to
their means expressed
Symbol | Definition |
---|---|
DANGER | The words after this sign mean there is a great potential |
danger, which may cause major accidents, damage or even death if it is not
followed.
WARNING| The words after this sign means there is some potential danger,
which may cause hurt or
property lose if it is not followed.
ATTENTION| The words after this sign mean there is a potential risk, which may cause equipment fault
or break, if it is not followed.
DANGER
Please follow the rules below to avoid heavy accidents.
- Never use the equipment to do other things but cutting.
- Follow related regulations for the construction of the input-driven power source, choice of place, usage of high-pressure gas, storage, configuration, safe-keeping of workpiece after cutting and disposal of waste, etc.
- Nonessential do not enter the cutting area.
- People using heart pacemaker is not allowed to get close to the cutting machine or area without a doctor’s permission. The magnetism created by energizing the cutting machine can have a bad effect to the pacemaker.
- Install, operate, check and maintain the equipment by professional personnel.
- Understanding the contents of the user manual for safety.
DANGER
Please follow the rules below to avoid electric shock。
- Keep away from any electric parts.
- Earth the machine and workpiece by professional personnel.
- Cut off the power before installation or checking, and restart 5 minutes later. The capacitance is a chargeable device. Please ensure it has no voltage before start again even if the power source is cut off.
- Do not use wire with an inadequate section surface or damaged insulation sleeve or even exposed conductor.
- Do ensure good isolation of wire connection.
- Never use the device when the enclosure is removed.
- Never use broken or wet insulation gloves.
- Use a firenet when working at a high position.
- Check and maintain regularly, don’t use it until the broken parts are fixed well.
- Turn off the power when not in use.
- Follow the national or local related standards and regulations when using the AC cutting machine at narrow or high positions.
DANGER
Please follow the below notes to avoid fire exploding, etc.
- No combustible in the cutting area.
- Keep off combustible when cutting.
- Keep hot workpiece after cutting away from flammable gas.
- Do move away the combustible around when cutting the dooryard, ground, and wall.
- The wire connection of the base metal should be as close to the cutting place as possible.
- Never cut those facilities with gas pipes or airtight slots.
- Put a fire extinguisher around the cutting area to prevent fire.
WARNING
The gas and fumes are harmful to health, please wear a protective device
according to regulations.
- Wear exhaust equipment and breathe preventive facilities to prevent gas poisoning or choking.
- Use suggested part exhaust equipment and breathe preventive facilities to prevent hurt or poisoning by gas and other powder, please.
- To prevent oxygen deficiency, air out the gas-filled room which is full of CO2 and argon on the bottom, When operating on trunks, boilers, cabins, etc.
- Please accept the supervisor’s inspection when operating in a narrow space. Air the room and wear breathe preventive facilities.
- Never operate in degrease, washing, or spray space.
- Using preventive facilities when cutting shielded steel for it will cause poisonous dust and gas.
The arc, spark, residue, and noise are harmful to health, please wear a protective appliance.
- Eye protection against arc is recommended when cutting or supervising cutting.
- Please wear preventive spectacles.
- Welder’s gloves, welder’s goggles, long sleeve clothes, leather apron, and other standard protection equipment must be worn for cutting operation.
- A screen to protect other people against the arc must be set in the cutting place.
Please follow the notes below to avoid the gas cylinder toppling over or breaking.
- Use the gas cylinder correctly.
- Use the equipped or recommended gaseous regulator.
- Read the manual of the gaseous regulator carefully before using it, and pay attention to the safety notes.
- Fix the gas cylinder with the appropriate holder and other relative parts.
- Never put the cylinder under high temperatures or sunshine environment.
- Keep your face away from the gas cylinder exit when opening it.
- Put on the gas shield when it is not used.
- Never put the torch on the gas cylinder. The electrode can not meet the gas cylinder.
Any touch of the switch part will cause injury, please note the following.
- Never use the machine when the enclosure is off.
- Install, operate, check and maintain the machine by professional person.
- Keep your fingers, hair, clothes etc. away from the switch parts such as the fan.
The wire end may deal damage, please note the following.
- Never look into the electric conduction hole when checking the wire feeding is normal or not, , or the shooting wire may stab your eyes and face.
- Keep your eyes, face or other naked parts away from the end of torch when feeding the wire manually or pressing the switch.
ATTENTION
For better work efficiency and power source maintenance, please note the
following.
- Precautions against toppling over.
- Never use the cutting equipment for pipe thawing.
- Lift the power source from side when use the up-down forklift truck to avoid toppling over.
- When using the crane for lift, tie the rope to the ears with an angle no more than φ15 to the vertical direction.
- When lifting the cutting machine which equipped with gas cylinder and wire feeder, download them from the power source and ensure the horizontal of the machine. Do fix the gas cylinder with belt or chain when moving it to avoid body hurt.
- Ensure fastness and insulation when lifting the wire feeder through the swing ring for cutting.
Electromagnetic interference needs attention.
- It may need extra preventive measures when the equipment is used in a particular location.
- Before the installation, please estimate the potential electromagnetism problems of the environment as follows.
- Upper and lower parts of the cutting equipment and other nearby power cable, control cable, signal cable and phone cable.
- Wireless electric as well as TV radiation and reception equipment.
- Computer and other control equipment.
- Safety-recognition equipment etc. Such as supervising of industrial equipment.
- The health of people around. Such as personnel using the heart pacemaker or audiphone.
- Equipment for adjustment and measurement.
- Anti-disturb capability of other used equipment . Users should ensure these equipment and the environment are compatible, which may need extra preventive measures.
- Practical state of the cutting and other activities.
- Users should observe the following dos and don’t to decrease radiation interference.
- Connect the cutting equipment to the power supply lines.
- Maintain the cutting equipment regularly.
- The cable should be short enough to be close to each other and the ground.
- Ensure the safety of all the cutting metal parts and other parts nearby.
- The workpiece should be well earth.
- Shield or protect the other cables and equipment to decrease the effects of disturbances. The cutting equipment can be completely shielded in some special conditions.
- Users are responsible for interference due to cutting.
Service GUARANTEE
This product is made of high-quality material and great care has been taken in its manufacture.It is designed to give good performance provided it is properly operated and maintained. The product is sold subject to the understanding that if any defect in manufacture or material shall appear within 12 months from the date of consumer sale if any defect in main parts over 12 months, the warranty period is subject to country Consumer Law, Our Service will arrange for such defect to be rectified without change under the following warranty items and conditions.
Warranty Terms and Conditions:
The defect is not due to use of the product for other than domestic purposes,
or an incorrect voltage, or use of improper accessories,or contrary to
operating instructions,or to accidental damage, misuse, neglect or inexpert
repair, or incorrect installation, or the product is excessively used for
improper purposes other than daily consumption, or accessories belonging to
the product, transportation. Thank you for choosing our products. Please feel
free to give your precious suggestions, we will make efforts to perfect our
products and service.
Warranty period from the purchase date :
- One-year warranty for welding and cutting machines.
- 1-month warranty for welding accessories.
- The warranty does not cover faults resulting from operation careless handling or not following instructions.
- Please register your after-sales service information in the following way to obtain the services and benefits you deserve.
- Customer:service@flartek.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>