ALLEN HEATH GS-R24 Balanced Analogue Interface Module User Guide
- June 14, 2024
- ALLEN HEATH
Table of Contents
GS R24
Balanced Analogue Interface Module 
USER GUIDE
Publication AP9109
Limited One Year Manufacturers Warranty
This product is warranted to be free from defects in materials or workmanship
for period of one year from the date of purchase by the original owner.
To ensure a high level of performance and reliability for which this equipment
has been designed and manufactured, read this User Guide before operating.
In the event of a failure, notify and return the defective unit to the place
of purchase.
If this is not possible then please contact the authorised ALLEN & HEATH
distributor or agent in your country as soon as possible for repair under
warranty subject to the following conditions.
Conditions of Warranty
The equipment has been installed and operated in accordance with the
instructions in this User Guide.
The equipment has not been subject to misuse either intended or accidental,
neglect, or alteration other than as described in the User Guide or Service
Manual, or approved by ALLEN & HEATH.
Any necessary adjustment, alteration or repair has been carried out by an
authorised ALLEN & HEATH distributor or agent.
This warranty does not cover fader wear and tear.
The defective unit is to be returned carriage prepaid to the place of
purchase, an authorised ALLEN & HEATH distributor or agent with proof of
purchase.
Please discuss this with the distributor or the agent before shipping.
If the unit is to be repaired in a different country to that of its purchase
the repair may take longer than normal, whilst the warranty is confirmed and
parts are sourced.
Units returned should be packed to avoid transit damage.
In certain territories the terms may vary. Check with your ALLEN & HEATH
distributor or agent for any additional warranty which may apply.
If further assistance is required please contact Allen & Heath Ltd.
IMPORTANT- PLEASE READ CAREFULLY:
By using this Allen & Heath product and the software within it, you agree to
be bound by the terms of the relevant End User Licence Agreement (EULA), a
copy of which can be found on the Allen & Heath website in the product’s
pages. You agree to be bound by the terms of the EULA by installing, copying,
or otherwise using the software.
This product complies with the European Electromagnetic Compatibility
directive 2004/108/EC and the European Low Voltage Directive 2006/95/EC.
This product has been tested to EN55103 Parts 1 & 2 1996 for use in
Environments E1, E2, E3, and E4 to demonstrate compliance with the protection
requirements in the European EMC directive 2004/108/EC.
During some tests the specified performance figures of the product were
affected. This is considered permissible and the product has been passed as
acceptable for its intended use. Allen & Heath has a strict policy of ensuring
all products are tested to the latest safety and EMC standards. Customers
requiring more information about EMC and safety issues can contact Allen &
Heath.
NOTE: Any changes or modifications to the console not approved by Allen &
Heath could void the compliance of the console and therefore the users
authority to operate it.
GS-R24 Balanced Analogue Interface Module User Guide AP9109 Issue 1
Copyright © 2013 Allen & Heath Limited. All rights reserved
Allen & Heath Limited
Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK
http://www.allen-heath.com
PACKED ITEMS
Check that you have received the following: 
GS-R24 BALANCED ANALOGUE INTERFACE MODULE
Also Packed in the box
- Safety Instructions—English
- Safety Instructions—French
- Addendum note ROHS
- Sticker
- This User Guide
CONTENTS
Thank you for purchasing your Allen & Heath GS-R24 Analogue interface module.
To ensure that you get the maximum benefit from the unit please spare a few
minutes familiarizing yourself with the features and setup procedures
outlined in this user guide.
For further information please refer to the additional information available
on our web site, or contact our technical support team.
http://www.allen-heath.com
This User Guide is to be read in conjunction with the GS-R24 console user
guide AP7784 in order to understand the routing of the interface signals to
and from the analogue system in the console. Also, some setup guides are
included on the Website for Digital Audio Workstations (DAWs). Please check
our website or with Tech Support for further information and setup guides.
GS-R24 ANALOGUE MODULE SPECIFICATIONS
General Specifications
Number of audio channels Output| 32
Number of audio channels Input| 32
Nominal Signal Level| +4dBu Balanced
Analogue signal connector type| 25 pin D-Sub Female (TASCAM standard pinout)
MIDI Input| Spin DIN
MIDI Output| Spin DIN
Headroom|
Analogue Headroom| 21dB
Channel Mapping to Interface
Console Channels| Interface Channels
Mono Channels 1-24| 1-24 *
Stereo Channel 1| 25-26 (L-R)
Stereo Channel 2| 27-28 (L-R)
Valve Channel 1| 29
Valve Channel 2| 30
Main Stereo (2 Track 1) out and DIG Master L-R in.| 31-32 (L-R)
- The interface sends 17-24 can be switched from Mono channels 17-24 to Aux |-4 and Groups |-4 in order to record or process summed or grouped signals. This is done by pressing the under-panel switch on the GS-R24 labelled 17- 24=Aux+Grp.
MODULE FITTING INSTRUCTIONS
Beware of ESD! Observe anti-static handling precautions—avoid touching the
electronic devices on the circuit board, ensure any static build up is
discharged to earth before handling the module.
This can be achieved by ensuring the console is connected to the psu and the
psu is plugged into a mains outlet but switched OFF, then touching a metal
part of the console panel such as a screw head.
Remove the blanking panel at the rear of the console by removing the 4 screws.
Locate the module circuit board in the plastic guide slots within the housing.
Slide the module into the housing and push firmly to insert the module
connectors into the console connector sockets.
Re-fit the 4 fixing screws to the module panel. 
To remove the module for any reason, the easiest way is to unscrew and remove the fixing screws at each end of the panel then use the D Sub cable connectors to gently pull out the module. A small side to side rocking action will help to displace the circuit board connectors from the internal mother-board.
25 PIN DTYPE CONNECTOR PINNING
Analogue Input & Output 25 way D connector pin ident. 
Pin assignment (Input or Output connectors)
Connection guidelines & notes
The pin assignment of the 25 pin D Sub Miniature type connectors conforms to
the TASCAM DB-25 pin-out standard developed over |5 years ago.
Multicore cable assemblies are readily available from audio equipment
suppliers or general electronic component suppliers such as Farnell and CPC in
the UK.
When choosing ready made cable assemblies, ensure that the cable mounted D Sub
connector is a 25-Pin Male type.
MODULE PANEL FEATURES
Investigate ALLEN & HEATH’s other ranges at www.allen-heath.com
PRODUCT SUPPORT
Investigate ALLEN & HEATH’s other ranges at www.allen-heath.com
Registering your product
Thank you for buying the Allen & Heath GS-R24 module. We hope that you are
happy with it and that you enjoy many years of faithful service with it, and
record and mix some great music.
Please go to www.allen-heath.com/register.asp and register your product’s
serial number and your details. By registering with us and becoming an
official Registered User, you will ensure that any warranty claim you might
make is actioned quickly and with the minimum delay.
Alternatively, you may either copy or cut off this section of the page, fill
in the details, and return it by mail to: Allen & Heath Ltd, Kernick
Industrial Estate, Penryn, Cornwall TR10 9LU, UK
Product Support: You can access Allen & Heath Tech Support by logging on to
www.allen-heath.com/support
ALLEN & HEATH PRODUC
Thankyou for buying an Allen & Heath product. We hope that you’re happy with it and that you enjoy many years of faithful service with it.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>