TIMOTOP 150W LED Barn Light User Manual

TIMOTOP 150W LED Barn Light

THANK YOU

Thank you for purchasing TIMOTOP products. If you have any questions during use, please feel free to contact our customer service team. We will quickly respond with 7 days+24 hours online service.

E-Mail:Timotop-VIP@outlook.com

SAFETY INFORMATION

WARNING: Read all safety precautions and installation instructions carefully before installing or servicing this fixture. Failure to comply with these instructions could result in a potentially fatal electric shock and/or property damage.

• To reduce the risk of electrical shock or other personal injury, ensure the power is turned OFF at the fuse or breaker box before making any electrical connections.
• For outdoor use only.
• Must be connected to 110-120 volt, 60 Hz power source.
• Fixture should be mounted to a grounded junction box marked for use in wet locations.
• Suitable for wall mount.
• NOT suitable for ground locations. Minimum of 4 feet or higher.
• Utility Light should be installed by a qualified electrician or person experienced with household wiring. The electrical system, and method of electrical connection of the fixture, must be in accordance with the National Electrical Code and local building codes.

SUITABLE FOR WET LOCATIONS
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR. MINIMUM 90°C SUPPLY CONDUCTORS.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

INSTALLATION KIT

PLANNING INSTALLATION

Carefully remove the fixture from the carton and check that all parts are included. Be careful not to misplace any of the screws or parts needed for installing the fixture.

• Wiring cap 3 PCS

• Glue plug 3 PCS

• screw 3PCS

• Hand screw 1 PCS

• Screw 3 PCS

• Hexagonal small wrench 1 PCS

PRODUCT ASSEMBLY STEPS:

1. Align the holes of handle and lamp body respectively.
   

2. Tighten the hand screw.
   

3. Straighten the wire and adjust the length of the wire.
   

INSTALLATION

A: Standard mounting

1. Stick the handle of the lamp on the wall and draw the position of the installation hole. Then make 3 holes in the wall, diameter cp0.31 ‘ hole depth 1.6″
2. Install the mounting rubber pfug in the hole;
3. connect the lamp power line, wiring polarity diagram, After connecting the wire, plug the wire into the handle;
4. Install the lamp on the wall with screws;
   
   CAUTION: Turn OFF the circuit breaker and light switch before beginning installation.

B: Arm mounting (Not included)

1. Install fixed pipe;
2. Connect the lamp power line, wiring polarity diagram, After connecting the wire, plug the wire into the handle;
3. he lamp into the extension tube, lock the screw;
   

ATTACH POWER SUPPLY WIRE

1. Connect the fixture ground wire (YELLOW-GREEN) to the ground supply wire using a wire nut.
2. Connect the BROWN fixture wire to the LIVE supply wire using the wire nuts.
3. Connect the BLUE fixture wire to the NEUTRAL supply wire using the wire nuts .

NOTE: For proper connection, place the wire nuts over the wires and twist clockwise until tight.
RECOMMENDED: Wrap each wire nut with electrical tape (Not Included).

TROUBLESHOOTING

B. Fuse is blown or circuit breaker is turned off.
C. Incorrect circuit wiring.| A. Photocell covered.
B. Replace fuse or turn circuit breaker on.
C. Verify that fixture is wired properly
Lights come on during the day.| A. Photocell covered.| A. Clean photocell with damp cloth
In normal use at night, the light suddenly turns off.| The sensor photocell may be affected by the following light sources: car lights/firelight/torch light and other light sources.| Change the direction of the sensing photocell or change the installation position of the lamp.

FCC WARNING:

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTES: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CONGRATULATIONS ON YOUR PURCHASE OF THIS LED WALL-MOUNTED FIXTURE

This light includes an integrated photocell which activates the light during low illumination (at dusk) and de-activates the light when illuminated (at dawn).

| LUX| PHOTOCELL| FIXTURE
---|---|---|---
DUSK| <BO LUX 80-150 LUX| ACTIVATES
NO ACTION|

ON
ON

DAWN

|

150 LUX
150-80 LUX

| ACTIVATES
NO ACTION| OFF
OFF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>