WANGMI PSBD-CS021DB Cordless Paint Sprayer User Manual

June 14, 2024
WANGMI

WANGMI LOGO Cordless Paint Sprayer PSBD-CS021DB
User Manual
WANGMI PSBD CS021DB Cordless Paint
Sprayer

Please read this manual carefully before using the paint sprayer, any improper use may cause equipment damage.

Explosive View

WANGMI PSBD CS021DB Cordless Paint Sprayer - FIGURE

1 ST2.9*10SCRE 27 Short pin
2 Rear cover 28 Adjusting knob
3 Cotton filter 29 Trigger
4 Right cover 30 Spray a knob
5 Switch plunger spring 31 Left side cover
6 Switch plunger 32 O-ring
7 Right side cover 33 Atomization circle
8 ST3.5*10SCRE 34 Vent spring
9 Big nut 35 Lock catch
10 Spray ball 36 Micro-switch
11 Spray nozzle 37 Battery Pack
12 Barge board 38 Battery pack pin
13 Nozzle seal 39 Left cover
14 Needle 40 Gun-ring
15 Needle insert 41 Stopper
16 Needle seat 42 Motor cover
17 Bowl seals 43 550 Motor
18 O-ring 44 Wind mill
19 22 Needle spring 45 M4*8 SCRE
20 Needle set 46 Motor gasket
21 Gun 47 Wind leaf
22 Pipette 48 Wind cover
23 Cup-ring 49 Damping ring
24 Suction pipe splint 50 Funnel
25 Sprayer Cup 51 Pin
26 Φ 3 flat gasket

Technical Parameters

Paint Sprayer Part Number: PSBD-CS021DB

Rated power: 200W| Lithium Battery Part Number: LB-MA4000-5CL
Rated voltage: 21V| Battery Voltage: 21V
Frequency: 50/60 HZ| Battery Capacity: 4000mAh
Rated speed: 30000 RPM| Battery Fully Charge: 3 ~4 hours
Max viscosity: 120 Din-s| Fully Charged Battery Spray: 2~2.5 Gal
Max flow: 1000ml/min| Battery with Level Display: Yes
Spraying width: 6”~12”(20-30cm)| Portable Charger Part Number: BC-DC21-SCNU
Best spray distance: 9”~14”(25-35cm)| Charger Input: 100V~240V
Paint Sprayer Cup Capacity: 30oz(900ml)| Charger Output: 21V

Warranty: For cordless paint sprayer main part, we offer 90 day returns and refunds, 12 month returns and exchanges, and 7×24 hour quick response customer service. If you have any questions, please contact us via your order or email us wangmi20140508@163.com , we will be always here for you!

What You Get

You will get:
Cordless Paint Sprayer × 1; 4.0 Ah Lithium Battery with Indicator Display × 1;2A Battery Charger × 1,;900ml Paint Sprayer Cup × 1;Brass Nozzles × 5;Plastic Viscosity Cup × 1;Cleaning Brush × 1; Cleaning Needle × 1;Paper Paint Filter × 5;User Manual × 1
In addition, we also offer additional accessories to buy, such as 4.0 Ah Battery , Paint Sprayer Cup, Paper Paint Filter, and Paint Filter Bag. You can find these accessories in our store, or you can contact us by email.

Warm Tips

  1. Before spraying, the surface dust should be cleaned up. The result of spraying largely depends on the smoothness and cleanliness of the surface to be coated.
  2. Before spraying, please add some water (or paint thinner) to dilute the paint and stir to ensure that your paint passes through the viscosity cup smoothly within 100 seconds.
  3. Before using, please select the appropriate size of brass nozzle and spray pattern, check whether the container and paint spray gun parts are tightened.
  4. Before using, practice the spray gun on cardboard or similar surfaces to check if the paint has been diluted to the appropriate viscosity.
  5. During using, move the spray gun horizontally or vertically evenly according to the setting of spray mode. The uniform motion of the spray gun produces a uniform surface quality.
  6. After spraying, remove the battery firstly, then clean the machine immediately to effectively prevent blockage. All components of the sprayer are detachable. Please use a cleaning brush and needle for proper cleaning to remove residual paint from containers, pipes, and nozzles. Use warm soapy water for latex materials, and mineral spirits for oil-based materials.

Special Attention:  When the paint cup is filled with paint, the paint spray gun should not be inverted. The spray gun must be held in the forward direction to avoid liquid blocking the air inlet, resulting in inability to discharge or damage to the paint spray gun.

How to Dilute Different Fluids

Before spraying, add some water (or paint thinner) to dilute the paint, please refer to the following thinning chart and picture.

Fluid Run Out Time(Sec)
Oil Enamel 25-60
Oil Based Primer 30-60
Oil Stain No thinning required
Clear Sealer No thinning required
Polyurethane No thinning required
Varnish 20-60
Lacquer sanding sealer 25-35
Lacquer 25-35
Automotive finishes 20-40
Latex 45-90

How to Choose Spraying Nozzle

Nozzle Size| Suggested Fluids| Reference viscosity| Recommend Project
---|---|---|---
1.0mm| Primer, Varnish, Oil-based Pigments, Cleaning Agent| 20-30 Din-s| Table, Chair, Bicycle, Shutter, Cabinets, Wooden Artwork, Model
1.5mm| Sealers, Stains, Enamel, Dyes| 30 Din-s| Table, Chair, Bicycle, Shutter, Cabinets, Wooden Artwork, Model
2.0mm| Polyurethane, Chalk Paint, Milk Paint, Automotive Paint| 40 Din-s| Railings, Multi-frame, Window Framer, Pipe, Boat, Yard, Furniture, Garage door,
Metal Garden Fences, Door
2.5mm| Low Viscosity Primer, Latex Wall Paint, Oil-based Lacquer| 40-50 Din-s| Internal Wall, Wooden Garden Fence, Wooden Pile, Corridor
3.0mm| Low Viscosity Primer, Latex Wall Paint, Emulsion Paint| 70-80 Din-s| External Wall, Outdoor Floor, Sports Field Line

Note:

  1. The above applicable fluids and project scenarios only represent our suggestions, and you can make adjustments according to your actual situation.
  2. This paint sprayer supports a maximum of 120 Din-s, you should ensure that your paint passes through the viscosity cup smoothly within 100 seconds.

How to use

  1. Installing and Removing the Battery
    (a) Install the battery: Align the base of the spray gun with the battery card slot, push the battery parallel and inward towards the red button position, until you hear a click to indicate that the battery is installed in place
    (b) Remove the battery: Hold the sprayer with one hand, while the other hand press the battery red button and pull it outward parallel to separate the sprayer and battery|
    ---|---
    A. Install the battery| B. Remove the battery
  2. Installing and Removing the Motor
    (a) Remove the motor: Hold the gun with one hand, press the latch in the direction of the arrow, and hold the motor handle with the other hand. Rotate it counterclockwise by 90 º and pull it out forcefully to remove the motor from the spray gun
    (b) Install the motor: Hold the gun with one hand, press the latch in the direction of the arrow, and hold the motor handle with the other hand. As shown in the figure, the motor handle is perpendicular to the spray gun, aligned with the insertion slot, and rotated 90 º clockwise to make them a straight line, which is locked

WANGMI PSBD CS021DB Cordless Paint Sprayer - Motor 1| WANGMI PSBD CS021DB Cordless Paint Sprayer - Motor
2
---|---
A. Remove the Motor| B. Install the Motor
3. Replace spraying nozzle
(1) By default, a spraying nozzle is already installed on the paint sprayer received by the user. If you feel that the size of the nozzle does not match your project, you can replace the nozzle yourself.
(2) Rotate the big nut of the sprayer head counterclockwise until the nut is separated from the sprayer, pull out the nozzle kit, remove the small seal ring and spray ball in turn, replace the appropriate nozzle and reassemble the nozzle kit, align the slot and insert the sprayer, install the big nut, rotate and tighten clockwise
(3) The nozzle kit can be installed vertically or horizontally, which will result in the paint spraying pattern being horizontal or vertical. It is also very simple to switch between these two installation methods. Loosen the big nut counterclockwise until you can rotate the nozzle kit according to your needs, and then tighten the big nut clockwise and inwardWANGMI PSBD CS021DB
Cordless Paint Sprayer - spraying nozzleReplace Spraying Nozzle

  1. Installing and Removing the Sprayer Cup
    (1) Install the spray cup: Hold the spray gun with one hand, align the spout of the spray cup with the cover with the other hand, and tighten it counterclockwise
    (2) Remove the spray cup: Hold the spray gun with one hand and loosen the spray cup clockwise with the other hand until they separate

  2. Adjusting the direction of the suction tube
    (a) Upward spraying project: You should open the lid of the cup, rotate the inclined tip of the suction tube and make it point towards the handle end
    (b) Downward spraying project: You should open the lid of the cup, rotate the inclined tip of the suction tube and make it be away from the handle end
    (c) In most cases, horizontal spraying is not necessary to adjust the direction of the suction tube|
    ---|---
    A: Upward Spraying| B. Downward Spraying

  3. Pour fluid into container, make sure not to exceed 900ml

  4. Adjusting the flow rate of paint spray
    (a) Rotate the flow thread knob clockwise upwards to reduce the amount and thickness of paint
    (b) Rotate the flow thread knob counterclockwise downwards to increase the amount and thickness of paint|
    ---|---
    A. Reduce Flow Rate| B. Increase Flow Rate

  5. Adjusting the spraying patterns
    (1) When the spraying nozzle is vertical , the side threaded knob “+” sign is at the top , the sprayed pattern is a horizontal oval shape; When the “+” sign rotates to the bottom , the sprayed pattern is circular shape.
    (2) When the spraying nozzle is horizontal , the side threaded knob “+” sign is at the top , the sprayed pattern is a vertical oval shape; When the “+” sign rotates to the bottom , the sprayed pattern is circular shape.

  6. Pull trigger, the paint will spray from the nozzle

Trouble Shooting

Problem Cause Solution
A. Little or no fluid flow 1. Nozzle clogged

2. Suction tube clogged
3. Fluid flow setting too low
4. Suction tube loose
5. Fluid is too thick
6. Inconsistent paint
7. Cup is loose| 1. Clean
2. Clean
3. Rotate the flow knob to increase fluid flow
4. Insert
5. Dilute paint
6. Strain paint
7. Tighten the cup
B. Fluid leaking| 1. Nozzle loose
2. Nozzle worn
3. Nozzle seal worn
4. Fluid build-up on spray pattern dial and nozzle| 1. Tighten
2. Replace
3. Replace
4. Clean
C. Atomization is too coarse| 1. Viscosity of fluid is too high
2. Fluid flow setting too large
3. Nozzle clogged
4. Too little pressure build-up in cup| 1. Dilute paint
2. Rotate the flow knob to reduce fluid flow
3. Clean
4. Tighten container
D. Spray jet pulsates| 1. Fluid in cup running out
2. Fluid is too thick| 1. Refill
2. Dilute paint
E. Pattern runs or sags| 1. Applying too much fluid| 1. Adjust fluid flow or increase movement of paint sprayer
F. Too much overspray| 1. Sprayer is too far from spray object
2. Too much fluid applied| 1. Reduce distance
2. Rotate the flow knob to reduce fluid flow
G. Pattern is very light and splotchy| 1. Moving the paint sprayer too fast| 1. Adjust fluid flow or decrease movement of paint sprayer
H. Large cloud of paint| 1. Sprayer too close to surface| 1. Move sprayer away from surface and reduce paint flow

Warning

  1. Keep your workplace clean and tidy, never use the tool in hazardous areas that contain flammable liquids, gasses or dusts
  2. Only use paints, solvents or other fluid with a flash point of 73℉(22℃) or higher.
  3. Never point the paint sprayer at other person or animal, in the event of an injury, seek immediate medical attention.
  4. Always read the paint manufacturer’s thinning instructions before use.
  5. You must clean the paint sprayer thoroughly after each use.

Warranty

For cordless paint sprayer main part, we offer 90 day returns and refunds, 12 month returns and exchanges, and 7×24 hour quick response customer service. If you have any questions, please contact us via your order or email us wangmi20140508@163.com , we will be always here for you!

WANGMI LOGO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals