BULBRITE 862655 6 Inch Recessed Downlight Instruction Manual

**BULBRITE 862655 6 Inch Recessed Downlight Instruction Manual

**

Product Instruction

Before installation, confirm all parts are in good condition.
If any parts are damaged, do not attempt to install Contact an American Lighting Association (ALA) Certified Relationship Specialist at Bulbrite for help with installation or questions about your kit at 800-528-5555 or [email protected].

These instructions are provided for your safety. |t is important that the instructions are read carefully and completely before assembling. Please save these instructions, as you may need them at a later date.

WARNING: RISK OF ELECTRIC SHOCK. BE SURE THE ELECTRICITY TO THE FIXTURE YOU ARE WORKINGON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKERIS TURNED OFF. TOPREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR OTHER SHARP OBJECTS. DONOT ALTER ANY WIRING ENCLOSURE DURING INSTALLATION. THIS LED RETROFIT MUST BEINSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE (NEC) AND RELEVANT LOCAL CODE. IF NOT QUALIFIED, DONOT ATTEMPT INSTALLATION. PLEASE CONSULT  ALICENSED ELECTRICIAN IF YOU HAVE ANYQUESTIONS. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT INSTALL THIS PRODUCT WHERE THERE IS A RISK OF RAIN OR MOISTURE EXPOSURE.INSTALL THISKIT ONLY IN THELUMINAIRES THAT HAVE THE CONSTRUCTION FEATURES AND DIMENSIONS SHOWN IN THE PHOTOGRAPHS AND/OR DRAWINGS LOCATED IN THESE INSTRUCTIONS. SUITABLE FOR DAMP LOCATIONS.

GENERAL INSTRUCTIONS:

• This fixture operates on line voltage (standard household power) of 120 Volts, 60 Hertz.
• Can be used in both dry and damp locations.
• Suitable for Type IC or NON-IC installations.
• Operation temperature ranging between -20°C to +45°C (-4°F to +113°F). Lamp life may be affected outside these temperatures.

See below for dims per model.
Height (Depth)

Size| Item No.| Item Description| Height (Depth)| Width| Equivalent| Cut Out Size| Jbox Dims
---|---|---|---|---|---|---|---
4″| 773301| LED12RECJBOXDL/4/5CCT/827-850/WHRD/D| 1.69″| 5.51| 65W| 41/4| 3.74″ x 3.46″ x 1.22″
6″| 773302| LED14RECJBOXDL/6/5CCT/827-850/WHRD/D| 1.89″| 7.32″| 75W| 5 1/2″| 3.74″ x 3.46″ x 1.22″

INSTALLATION INSTRUCTIONS:

STEP : 1

Power off all electricity to the luminaire.
**STEP : 2

Check the space above the ceiling of your desired installation location and ensure that there is enough space to accommodate the box. Box dimensions are included in chart above. Please ensure there is a 1 3/4″  airspace above the light for both 4”and 6″ models.
STEP : 3

** Cut a hole in the ceiling for your fixture. Before you begin, ensure that the hole you are going to be cutting does not interfere with studs, piping, electrical or other building structures. See the above chart for cutting size or refer the the appropriate template for your model.

Height (Depth)
See below for dims per model.
**STEP 4

**

Using a screw driver, carefully remove the knock out as shown above.

**STEP 5

**

Reminder: Installation requires electrical knowledge, If not qualified, do not attempt installation. Contact a qualified electrician. Remove the junction box cover. Feed supply wire into knockout.

STEP 6

Make wiring connection inside the junction box using the EZ connectors (as shown above). Connect the 120V line wire from your house electrical to the black wire (black to black). Connect the neutral wire to the white wire (white to white).
Note: If you are replacing an existing fixture where ground wire is present, you can connect incoming ground wire to the extra EZ connector included. If wiring to another fixture, connect outgoing ground wire to the same EZ connector.

STEP 7

Snap closed junction box cover. It will click once in place.

STEP 8

Connect downlight to the box via the twisting mechanism on the white cord coming from each item.

STEP 9

Holding spring clips against fixture, carefully insert the fixture into the hole. Continue to slide in the fixture, releasing spring clips, until clips snap into place. Ensure the fixture is flush against the ceiling and securely in place.

STEP 10

Turn on all electricity to the luminaire and installation is complete.

MULTIPLE FIXTURE CONNECTIONS:

If you intend to connect multiple fixtures (daisy chain / feed through installation), insert the additional wire into the adjacent knockout using appropriate electrical fittings and repeat from Step 6.

145 WEST COMMERCIAL AVE, MOONACHIE NJ 07074
T: 800 528 5555
www.bulbrite.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>