RECC REPW50 Wireless TWS Earphone User Manual

June 14, 2024
RECC

RECC REPW50 Wireless TWS Earphone

Product Usage Instructions

Installation

  1. Choose a suitable location for the device.
  2. Ensure the device is placed on a stable surface.
  3. Connect the necessary cables and power supply to the device.
  4. Ensure all connections are secure.
  5. Power on the device.

Operation

To operate the device:

  1. Refer to the user manual for specific functions and features.
  2. Use the provided remote control or on-device controls to navigate through menus and settings.
  3. Follow the on-screen instructions for desired actions.
  4. Adjust any necessary settings according to personal preferences.
  5. Ensure the device is placed in a well-ventilated area to prevent overheating.

Maintenance

To maintain the device:

  1. Regularly clean the device using a soft, dry cloth.
  2. Avoid using any harsh chemicals or abrasive materials during cleaning.
  3. Keep the device away from excessive moisture or extreme temperatures.
  4. Perform any recommended firmware updates to ensure optimal performance.
  5. Contact customer support for any technical issues or concerns.

Product structure

FIG RECC- REPW50- Wireless -TWS -Earphone FIG-2

Specifications

  • Compliance: Part 15 of the FCC Rules
  • Interference: Must not cause harmful interference
  • Interference Acceptance : Must accept any received interference, including interference that may cause undesired operation

RECC- REPW50- Wireless -TWS -Earphone-FIG-4

  1. Wireless pairing  Open the charging box, take out the earphone and turn it on automatically.
  2.  Earphone that have not been connected to the device will automatically enter the pairing mode (and try to connect back to the last connected mobile phone);Open wireless connect interface on mobile phone, searching for “REP-W50”, click pairing, there has a prompt tone when connecting successfully.

Power on / off

Power on :

  1. Open the charging box, take out the earphone and tum it on automatically, earphones are automatically paired and waiting for connection.

Power off :

  1. When connecting the phone, put the L/ R earphone into the charging box.After the cover is closed, the earphone shuts down and starts charging (L or R)
  2. Elf the earphone is not connected to any device for 3 minutes, or the battery is lower than 3.1V, the earphone will automatically shut down.

Single side earphone use

  1.  Open the charging box, take out the earphone and turn it on automatically, earphone are automatically paired and waiting for connection.
  2.  Then open the mobile phone and search for the device name ‘REP-W50″. After suocessful connection, take out any L / R headset and use it.
  3.  Put the earphone back into the charging box and close the cover, the earphone will immediately shut down and enter the charging state.

Calling use
When using the call function, the L/ R earphones can perform the following operations:

  • Answer : When there is an incoming call, double-click the multi-function touch area.
  • Reject : During a call, double-click the multi-function touch area.
  • Hang up : When there is an incoming call, long press the multi-function touch area.

Wake up voice assistant function (If your phone support this function)
In the power on state, long press the multi-function touch area for 3 seconds to start the voice assistant function (Siri).

Music use

  • Music pause/play: when connected / played, double-click the multi-function touch area.
  • Previous song: when music is playing, triple click the left ear multi-function touch area (left ear L).
  • Next song: when music is playing, triple click the right ear multi-function touch area (right ear R).
  • Volume increase: when music is playing, click the right ear multi-function touch area (right ear R).
  • Volume reduction: when music is playing, click the left ear multi-function touch area (left ear L).

Charging indicator light

  1. Use USB cable to charge the charging box:
  2. Charging : the red light flashing.
  3. Charged fully : the red light is always on.
  4.   Low power : prompt “Battery Low’.
  5. Earphone charges automatically when put them into charging box:
  6. Charging : the green light of the earphone is always on.
  7. Charged fully : the earphone green light stays on 8-10 seconds and then goes out.

Matters needing attention

  •  The main earphone serves as a bridge between the secondary earphone and the mobile phone without interruption, and it is normal for the power consumption to be greater than that of the secondary unit.
  •  Apple mobile phone displays the battery power in real time.
  •  Wearing method is very important to avoid the signal antenna is blocked by the inside of the ear Block, please wear according to the introduction page wearing method.
  •  In the binaural mode, any one-side earphones will cause a bad signal by hand. This type of technology earphone all has this situation, because The equivalent of blocking the signal connection between the two earphones by hand.
  •  In binaural mode, there must not be too many intertering objects between the earphone and the main earphone, and the distance between the two needs to be ensured so as not to affect the signal transmission between the mobile phone and the main earphone (R earphone).
  •  In binaural mode, if the secondary earphone (L earphone) has an occasional disconnection problem It is a normal phenomenon, wireless signal transmission same Like the WiFi network, sometimes instability is normal. At this point, just the signal transmission is disturbed, please wait a moment or move to another place.

Warning

  1. Do not use corrosive cleaners to clean the product.
  2. Do not allow this product to be heated or near a fire source.
  3. Do not expose the product to direct sunlight for a long time.
  4. Do not discard the product in the fire to avoid explosion.
  5. Do not make any modifications to try to disassemble this product because it does not contain any modifiable components.
  6. Do not use this product in the rain.
  7. If you do not use this product for a long time, please store it in a dry environment and charge the headset at least once a month to prolong its service life and avoid extreme temperature and dust.
  8. You must choose a regular charger from a qualified manufacturer to charge the earphone.

FCC

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

  1.  This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

FAQ (Frequently Asked Questions)

  • Q: What should I do if the device is not powering on
    A: First, ensure that the power cable is securely connected to both the device and a power outlet. If the issue persists, try using a different power outlet or power cable. If the problem still persists, contact customer support for further assistance.

  • Q: How can I reset the device to factory settings
    A: To reset the device to factory settings, locate the reset button on the device (refer to the user manual for its specific location). Press and hold the reset button for approximately 10 seconds until the device resets. Note that this action will erase all saved settings and data on the device.

  • Q: Can I connect external speakers to the device
    A: Yes, you can connect external speakers to the device. Use the provided audio output ports or consult the user manual for specific instructions on connecting external speakers.

RECC- REPW50- Wireless -TWS -Earphone-FIG-1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals