simu 5124422D Wall Hz Transmitter Instructions

simu 5124422D Wall Hz Transmitter

Presentation

The wall Hz transmitter 1C US(1channel) enables the individual, group or general command of SIMU-Hz motors and receivers.

1. UP control key
2. STOP / P.I. (§5) control key
3. DOWN control key
4. Programming button « PROG »
5. Transmission indicator

Figure A

Technical data

• Compatible with motors & receivers
• Safety level: class III
• Frequency bands and maximum power used : 433,050 MHz – 434,790 MHz. US and Canada maximum e.r.p. < 63 ɥW.
• Radio range (in normal pollution condition): 20ft max. (6m max) through 2 concrete walls, (164ft (50m) in free field. The use of the control point in the same room as the controlled products is recommended. The environment in which the product is used might reduce the radio range.
• Power supply: 1 type CR2032 battery, 3 V.

Safety and liability

1. Liability
   These instructions must be kept by the user. Failure to follow these instructions or use of the product outside its field of application is forbidden, and will invalidate the warranty and discharge SIMU of all liability. This SIMU product must be installed by a professional drive and home automation installer. Moreover, the installer must comply with the standards and legislation currently in force in the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for the product. Never begin installing without first checking the compatibility of this product with the associated equipment and accessories. If in doubt when installing this product and/or to obtain additional information, contact a SIMU adviser or go to the website www.simu.com.

2. Safety instructions
   If used with a motor, you should also consult the instructions provided with the motor.
   Do not use or install this product outdoors. Keep the product out of the reach of children.
   Do not use abrasive products or solvents to clean it. Do not knock or drop the product, expose it to flammable materials or sources of heat or moisture, or splash or immerse it.

Warning
This product contains a button battery. Do not swallow the battery: risk of potentially fatal chemical burns in less than 2 hours. If the battery is inserted into a part of the body or if in any doubt, call a doctor immediately. Keep batteries (new and used) and the product out of the reach of children. If the battery compartment no longer closes, do not use the product and keep it away from children. Risk of explosion, leaking flammable liquids or gases from the battery if it is kept at a high temperature (hot oven, fire), crushed, cut or subject to very low air pressure. Non-rechargeable batteries must not be recharged.

Installation

This product must be installed on a wall, and SIMU recommends that this surface be flat.
This product must not be installed at a height greater than 2 m.
Do not position the transmitter near metal in order to ensure its good working (reduced range). A radio appliance using the same frequency may deteriorate our product’s performance.

Figure B

Programming The Transmitter With An Existing Installation

1. Open the memory of the motor using its individual control transmitter:
   • Press the Prog. Button for about 3 sec. on the motor’s individual control transmitter, the motor will jog.
2. Then validate the operation from the new transmitter to be programmed:
   • Press the Prog. Button for about 1 sec. on the new transmitter, the motor will jog.
     For group controls from the new transmitter, repeat operations 1. and 2. for each motor of the group.
     For main controls from the new transmitter, repeat operations 1. and 2. for each motor of the installation.
     To delete a transmitter from the memory of a motor, perform operation 1. with a programmed transmitter, then perform operation 2. with the transmitter to be deleted.
     For more complete information about programming, please refer to the instructions of the motor used.
     Figure C
     

Recording And Controlling Intermediate Position (I.P.)

Refer to Hz motor instructions to make sure it has this feature.

1. Recording:
   Move the motor to the wanted position.
   Press 5 seconds on the STOP key. The motor will run for 0.5 second in one direction and then in the other.

2. Controlling:
   Press the STOP key for 0.5 second. The motor runs to the intermediate position.
   Figure D
   

Replacement Of The Battery

Read the chapter entitled Safety instructions.
Risk of explosion if the battery is replaced by an incorrect type.
No new programming is needed after replacing the battery.
Please separate storage cells and batteries from other types of waste and recycle them via your local collection facility.
We care about our environment. Do not dispose of your appliance with the usual household waste.
Take to an accredited collection point for recycling.
Figure E

FCC Warning Statement

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.
• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Customer Support

SIMU S.A.S. au capital de 5 000 000 € – Zone Industrielle Les Giranaux – 70100 ARC-LÈS-GRAY – FRANCE – RCS VESOUL B 425 650 090 – SIRET 425 650 090 00011 – n° T.V.A CEE FR 87 425 650 090

http://www.simu.com/

5124422D

Documents / Resources

| simu 5124422D Wall Hz Transmitter [pdf] Instructions
5124422D, 5124422D Wall Hz Transmitter, Wall Hz Transmitter, Hz Transmitter, Transmitter
---|---

References

• Fabricant moteurs volets roulants depuis 1952 - Simu
• Fabricant moteurs volets roulants depuis 1952 - Simu

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>