SOUTHBEND 10CCH Series Electric Convection Ovens User Manual

**SOUTHBEND 10CCH Series Electric Convection Ovens User Manual

**

Information

Replacement parts may be ordered either through a South bend Authorized Parts Distributor or a South bend Authorized Service Agency. It is recommended to verify part numbers with a South bend Authorized Parts Supplier or the South bend Parts/Service Dept. prior to ordering parts.

When ordering parts, you will need to supply the Model Number, Serial Number, Part Number, Description, Finish, and Electrical Characteristics as applicable to the unit.

The serial plate is located on the interior side of the lower front panel, as shown below.

Specifications

ELECTRICAL SUPPLY

The following table lists the electricity supply requirements PER OVEN (double for dual-oven models).

Supply Voltage| Oven Component| Total kW| 3-Phase Loading (kW/phase)| Nominal Amperes per Line-Wire| Minimum Supply Wire (AWG) Size
---|---|---|---|---|---
3-Phase| 1-Phase Total
L1-L2| L2-L3| L1-L3| L1| L2| L3| 3-Phase| 1-Phase
480| Heating Elements| 11.00| 3.67| 3.67| 3.67| 13.2| 13.2| 13.2| 22.9| 12| 10
Motor & Controls| 0.90| 0.00| 0.00| 0.00| 2.2| 0.0| 2.2| 2.2
415| Heating Elements| 11.00| 3.67| 3.67| 3.67| 15.3| 15.3| 15.3| 45.9| 12| 6
Motor & Controls| 0.90| 0.00| L3-N| 0.90| 0.0| 0.0| 3.8| 3.8
380| Heating Elements| 11.00| 3.67| 3.67| 3.67| 16.7| 16.7| 16.7| 28.9| 12| 8
Motor & Controls| 0.90| 0.00| L3-N| 0.90| 0.0| 0.0| 4.1| 4.1
240| Heating Elements| 11.00| 3.67| 3.67| 3.67| 26.4| 26.4| 26.4| 45.8| 8| 6
Motor & Controls| 0.90| 0.00| 0.00| 0.90| 3.8| 0.0| 3.8| 3.8
220 (50Hz)| Heating Elements| 9.25| 3.10| 3.10| 3.10| 24.2| 24.2| 24.2| 42.0| 8| 6
Motor & Controls| 0.90| 0.00| 0.00| 0.90| 4.1| 0.0| 4.1| 4.1
208| Heating Elements| 11.00| 3.67| 3.67| 3.67| 30.5| 30.5| 30.5| 52.9| 8| 4
Motor & Controls| 0.90| 0.00| 0.00| 0.90| 4.3| 0.0| 4.3| 4.3

An electrical diagram is located on the side of the control panel assembly (see drawing on page 5). Electrical diagrams can also be found in the Operator’s manual.

The appliance, when serviced, must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2, as applicable.

Use 167 °F (75 °C) wire for all supply lines.

Ovens are shipped wired for either single-phase or three-phase operation, depending on which was specified on the factory order. If necessary an oven can be field-converted. Reference Operator’s Manual for wiring connection information.

The electrical connections are made directly to the terminals of the heating- element contactor, which is located inside the control-panel compartment on the right side of the oven. A circular opening sized for a strain-relief fitting is located on the back of the oven near the right side (on right as seen from the front of the oven, see illustration on page 4). Models with two stacked ovens have a separate electrical connection for each oven.

Connecting Electrical Supply

The following drawing shows the locations of items for the 208-240V electrical supply. Reference Owners manual for other voltage options.

Electrical Connection Access

1. CHECK THAT THE POWER SUPPLY CIRCUIT BREAKER IS OPEN.
2. Locate and remove the four screws that secure the lower front panel (items “A” in the drawing above). Lift up the panel and pull it forward to remove it, then set it aside.
3. Locate and remove the front screw (item “B” in the drawing above), that secures the lower front corner of the side panel.
4. Locate and remove the five rear screws that secure the back edge of the side panel to the oven (items “B” in the drawing above). Remove the side panel and insulation and set them aside.
5. Route the supply wires and the grounding wire through the hole on the back of the oven. Use a strain relief fitting.
6. Attach each supply wire to the appropriate terminal of the contactor (according to wiring diagram).
7. Insert the ground wire into the grounding lug and tighten the screw.
8. Check that all connections match the wiring diagram and are tight.
9. Reattach the right-side panel and insulation; and front panel using screws removed in steps 1 thru 4.

Control Panel Access and Shut-Off Switch

To access the control panel components, remove the remove the two thumbs screws at the top and bottom of the control panel and slide the control panel out (see 1ST picture). A wiring diagram for the oven is located on the side of the control panel assembly When the control panel is slid out, all power to the control panel is cut off by a shut down switch that is located directly inside the opening and below the control panel (see 2ND picture). To re- energize the controls for troubleshooting, pull the white plunger on the shut down switch up.

To fully remove Control Panel, disconnect temp probe wires and harness connectors prior to pulling up on slide release levers and removing.

Accessing Control Panel Components

Parts

NOTICE
Installation of other than Genuine Southbend Parts will void the warranty on this equipment.

The serial plate with voltage, model, and serial information is located inside the lower front panel of the oven.
Replacement parts may be ordered either through a Southbend Authorized Parts Distributor or a Southbend Authorized Service Agency. It is recommended to verify part numbers with a Southbend Authorized Parts Supplier or the Southbend Parts/Service Dept. prior to ordering parts.
When ordering parts, you will need to supply the Model Number, Serial Number, Part Number, Description, Finish, and Electrical Characteristics as applicable to the unit.
For parts not listed, contact a Southbend Authorized Parts Distributor or Southbend Authorized Service Agency. You can find an Authorized Parts Distributor or Service Agency in your area by going to www.southbendnc.com/service.html.
If this information is not available, contact the Parts/Service Dept. at Southbend to obtain specific part availability and information.

Index of Parts Diagrams

PaGe Number| Description
7| Front Panel and Flue Parts
8| Door Parts
9| Door Chain Mechanism Parts
10| Control Panel Parts for Models with Standard Controls
12| Control Panel Parts for Models with Cycle/Cook and Hold Controls
14| Control Panel Parts for Models with Touch Control
16| Oven Interior and Fan Motor Parts
17| Oven Light Parts
18| Side Compartment Parts
19| Leg Parts for Single-Deck SilverStar Models
20| Storage Rack Parts
21| Double-Deck Oven Stacking Parts
22| Leg Parts for Double-Deck Ovens

Front Panel and Flue Parts

Door Parts

Door Chain Mechanism Parts

Control Panel Parts for Models with Standard Controls (SC Models)

See drawing on following page.

w/o wiring harness)
–| 1198035| 1| Control panel s/a, SC, 60Hz, G-Series, 480V (assembled, w/o wiring harness)
–| 1198036| 1| Control panel s/a, SC, 60Hz, S-Series, 208/380/415V, w/lights (assembled, w/o wiring harness)
–| 1198038| 1| Control panel s/a, SC, 60Hz, S-Series, 208/380/415V, w/o lights (assembled, w/o wiring harness)
| 1198040| 1| Control panel s/a, SC, 50Hz, S-Series, 208/380/415V, w/lights (assembled, w/o wiring harness)
–| 1198041| 1| Control panel s/a, SC, 50Hz, S-Series, 208/380/415V, w/o lights (assembled, w/o wiring harness)
–| 1198037| 1| Control panel s/a, SC, 60Hz, S-Series, 480V, w/lights (assembled, w/o wiring harness)
–| 1198039| 1| Control panel s/a, SC, 60Hz, S-Series, 480V, w/o lights (assembled, w/o wiring harness)
| 1179593| 1| Wiring harness, SC
1| 1197782| 1| Frame Assembly, Std., Slide
2| 1198001| 1| Polypanel, G-Series
1198000| 1| Polypanel, SL-Series
3| 1177541| 1| Rocker switch-DPST- (on-off)
4| 1177540| 2| Rocker switch-SPDT (on-on)
5| 1170350| 1| Light, amber, 240V, signal
6| 6600334| 2| Screw, 6-32, 3/8, Self-tapping
7| 1170424| 2| Fuse holder
8| 1170425| 2| Fuse, 12 amp #LP-CC-12 low peak
9| 1177789| 1| Rocker switch-SPST momentary (for models with the optional oven light)
1177642| 1| Plug, square (for models without the optional oven light)
10| 1198084| 1| Push mount wire tie
11| 1170336| 1| Marker strip
12| 1170335| 1| Terminal block (supplied w/harness)
13| 2001347| 3| Locknut, 8-32
14| 1146397| 3| Screw 8-32 x 5/8 s/steel pan head
15| 1181998| 1| Temperature control board/analog potentiometer
16| 1175708| 1| Buzzer, adjustable, 240VAC
17| 1176416| 1| Timer, motorized, 240V, 60Hz
1176436| 1| Timer, motorized, 240V, 50Hz
| 1181996| 1| Temperature probe
18| 1170337| 2| Knob for temperature control bd. and timer
19| 1146319| 1| Screw 6-32 x 1/2 round head
| 1062100| 1| Wire nut (for models without the optional oven light)
| 1166609| 10| Ties, cable, ty-rap, 4″

• not shown on drawing.

See parts list on previous page.

(assembled, w/o wiring harness)
–| 1198011| 1| Control panel s/a, CCH, 60Hz, G-Series, 480V (assembled, w/o wiring harness)
–| 1198012| 1| Control panel s/a, CCH, 60Hz, S-Series, 220/380/415V, w/lights (assembled, w/o wiring harness)
–| 1198014| 1| Control panel s/a, CCH, 60Hz, S-Series, 220/380/415V, w/o lights (assembled, w/o wiring harness)
–| 1198013| 1| Control panel s/a, CCH, 60Hz, S-Series, 480V, w/lights (assembled, w/o wiring harness)
–| 1198015| 1| Control panel s/a, CCH, 60Hz, S-Series, 480V, w/o lights (assembled, w/o wiring harness)
| 1180484| 1| Wiring harness, CCH
1| 1197783| 1| Frame Assembly, CCH, Slide
2| 1177540| 2| Rocker switch-SPDT (on-on)
3| 1198003| 1| Polypanel, CCH, G-Series
1198002| 1| Polypanel, CCH, S-Series
4| 1177541| 1| Rocker switch-DPST- (on-off)
5| 1170424| 2| Fuse holder
6| 1170425| 2| Fuse, 12 amp #LP-CC-12 low peak
7| 1177789| 1| Rocker switch-SPST momentary (for models with the optional oven light)
1177642| 1| Plug, square (for models without the optional oven light)
8| 1198084| 1| Wire Tie, push mount
9| 1170336| 1| Marker strip
10| 1170335| 1| Terminal block
11| 2001347| 4| Locknut, 8-32
12| 1146397| 4| Screw 8-32 x 5/8 s/steel pan head
13| 1180404| 4| Spacer, control
14| 1180407| 1| Control, CCH
15| 1146400| 4| Nut, #6-32 hex
16| 1180499| 1| Relay, 208/240V
| 1181996| 1| Temperature probe
| 1166609| 10| Ties, cable, ty-rap, 4″

• not shown on drawing.

See parts list on previous page.

Oven Interior and Fan Motor Parts

6

| 1175263| 1| Element asm. 208V
1175264| 1| Element asm. 240V
1175414| 1| Element asm. 380V
1175265| 1| Element asm. 480V
7| 1189821| 5| Rack, oven, shallow, mg
1189860| 5| Rack, oven, bakery. mg
8| 1189820| 2| Rack guide, 11 pos, shallow
1189822| 2| Rack guide, 11 pos, bakery
9| 6660| 8| Clip, side rack support
10| 1175146| 1| Bolt, carriage, 3/8, ss
11| 1175407| 1| Tube, w/a, moisture vent
12| 1080303| 1| Gasket, silicone, .062 ga.
13| 1179104| 1| Blower wheel, G & E series
*| 1179100| *| Puller disk
14| 1175146| 4| Nut, 3/8, ss
15| 1175705| 1| Pocket w/a, blower motor
16| 1195439| 2| Insulation, elements
17| 1175256| 1| Cover, rear, elements
18| 1175568| 1| Motor, 2sp, 230V, 50/60 cycle
19| 1146264| 4| Screw, 1/4-20 x 2
    not shown on drawing.** SERVICE TOOL; may be needed to remove blower wheel.

Oven Light Parts

*          not shown on drawing.

Side Compartment Parts

Leg Parts for Single-Deck Models

• not shown on drawing.

Storage Rack Parts

• not shown on drawing.

Double-Deck Oven Stacking Parts

Leg Parts for Double-Deck Ovens

• not shown on drawing.

User & Maintenance Notes:

A product with the South bend name incorporates the best in durability and low maintenance. We all recognize, however, that replacement parts and occasional professional service may be necessary to extend the useful life of this appliance.
When service is needed, contact a Southbend Authorized Service Agency, or your dealer. To avoid confusion, always refer to the model number, serial number, and type of your appliance.

SOUTHBEND
A Middleby Company
1100 Old Honeycutt Road Fuquay-Varina, North Carolina 27526 USA
www.southbendnc.com

References

• Commercial Kitchen Equipment | Southbend Restaurant Equipment
• Service and Parts - Southbend

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>