Metoluar WS-1050-QX 8 In 1 Wireless Weather Station User Manual

User Manual
WS-1050
Professional Wireless Weather Station with APP
（Wifi and Bluetooth）

Function Declaration

WS-1050 is a professional weather station with WiFi, Bluetooth, users can view the latest weather data anytime and anywhere through their mobile phone (APP kit).

Discriptions：

1. Calendar:Date display format is YYYY-MM-DD、MM-DD- YY、DD-MM-YY（User chooses to set up）
2. Clock display: Clock display format can bu customized ,set to 12 hours or 24 hours.
3. Automatic calibration time: Indoor computers can connect to the Internet via WiFi，automatic synchronization of current phone time，
4. Alarm clock :BI BI alarm sound to alert users，the alarm clock rings 2 minutes.If you cancel the alarm press touch key.
5. Wireless 433MHz receiving: indoor and outdoor transmitters receive about 100m from the open space, data frequency 40 seconds / 1 launch.
6. Indoor humidity : Relative humidity display,can set the alarm value of high humidity and low humidity independently, scope:20RH%~90RH%.
7. Indoor temperature: Can set the alarm value of high temperature and low temperature independently,the user may set the unit at ℃ or Fahrenheit，scope: 0℃~60℃.
8. Outdoor humidity: Relative humidity display,can set the alarm value of high humidity and low humidity independently, scope:20RH%~90RH%.
9. Outdoor temperature:Can set the alarm value of high temperature and low temperature independently,the user may set the unit at ℃ or ℉，scope: -40℃~60℃.
10. Wind speed: User can set display wind speed units，can independently set the wind speed high alarm value, the display unit can be set tom/s、km/h、mph、knots or bft，scope:0m/s~50m/s.
11. Rainfall :Rainfall can be displayed in 1H、24H,、week、 month,、year or total amount. The display unit can be set to mm or inch (user setting).The total rainfall was 9999mm;APP can set the alarm value of high hourly rainfall, ranging from 0mm to 400mm.
12. Wind direction :N,NE,E,SE,S,SW,W,NW eight wind direction can be displayed.
13. Pressure:The air pressure is shown as absolute pressure, It can set high voltage alarm value and low voltage alarm value independently, and display unit can be set to Hpa or Inhg or mmhg, scope 300hpa~1100hpa(±3 hPa).
14. Pressure change trend:Pressure trend is indicated 24H variation trend.
15. Weather forecast shows: Sunny、Cloudy、Overcast、Rainy four states icons and weather trends.
16. Low voltage detection:If the battery voltage of the receiver and transmitter is insufficient,can flicker separately to remind users to replace batteries as soon as possible(Low voltage of indoor battery around 3.2V).
17. Power supply: Alkaline battery 3 × AA 1.5V battery life more than 2 months (battery capacity determines service time).
18. External DC power supply: 5V/500mA.
19. Backlight :If you lightly touch the button, the LED backlight will be turned on for 36 seconds. Long press 3 seconds to keep the light on, and then long press 3 seconds to cancel the light.
20. Buzzer: All weather data alarm function can be set independently, the user can set the upper / lower limit value within the design parameter range, the alarm time is 2 minutes sound is bibi.

LCD display: The local LCD is shown below,after the user loads the battery,before the machine goes into normal operation,all icons will be displayed for two seconds;

After the user loads the battery, the machine starts searching for outdoor sensors immediately after initializing. If no target is found within three minutes,think this search failed，once the target is searched,this machine will only establish a data connection with the sensor,synchronize the data of the sensor in 40 seconds,so in order to ensure that the machine works properly, be sure to install the outdoor sensor before switching to the battery ，during the search process The icon will always flicker，icon displayed after search for outdoor unit，icon disappeared after search failed（Press the touch button after disappearing，continue to start long receive mode），During the search process,please do not do anything with this machine.
This machine can be automatically calibrated by WiFi connection，if you set up the WiFi，it can be automatically checked
through the Internet every 12 hours.or user can use APP to update the receiver time via Bluetooth.

APP Operations

APP Mobile phone runtime environment（Tablet PC are not supported)

1. IOS Run environment compatible version Suitable for iOS 8.0 or above
2. Android version

For Android 5.1 above.

1. Download installation APP：Two-Dimensional codes for scanning instructions / Color boxes，Download and install APP.

2. Open APP，APP the startup interface is as follows：http://url.lnk1.cn/23744688

3. After starting the interface，display main interface，click on the upper left corner. Setting button，As shown below(1)：

4. connection WiFi settings, click Available Devices, to enter the Available Devices interface, as shown below(2):

5. Click on the top right corner of the Available Devices interface Search, into the Bluetooth search interface, search the product — WS1050-XXXX,as show below:

6. WiFi setup connection:Click to search the product name WS1050-XXXX Bluetooth MAC address), pop up the WiFi setup interface, enter the WIFI connection password in the Password column, after setting up, click on the upper right corner Send to send, as show below：

7. After configuring a successful OK, APP jumps back to the Available Devices interface, as shown below：

8. Click on the product name attached to the Available Devices list and jump to the main interface to see the product receive as shown below：

9. Click the historical data icon to enter the historical data interface. You can customize the date And time to view historical data

10. APP data update settings：
    Data upload cloud time setting，Click iCloud Setting, the first two IP and Port remain the default.
    Click The user sets the update interval according to the actual need.Minimum 10 minutes (others keep default 30 minutes), maximum 100 minutes.
    Click on the upper right corner icon withdraw from as show below:

11. Unit setting
    Click Uints Setting, and the user sets the unit according to the actual needs, as shown below:
    Each data unit is displayed in the first unit value as the default unit of the system,users are free to choose units according to their needs.
    Click on the upper left corner Icon exit, as show below:

12. Alarm setting:
    Click Alarm Setting The user sets the upper and lower limits according to the range of design parameters .For example, temperature ：0℃～60℃ (32℉～140℉)。After the alarm value is set，click the upper right save icon to exit, as shown below：In the Alarm Setting interface, you can view the categories of alarm history data, click on the upper right corner—- as shown below:(Historical alarm data)

13. Alarm clock setting：
    Click on Alarm Clock Setting, user to set alarm clock mode and time according to actual needs;
    Alarm clock can be set: no alarm clock, every day, weekend, working day four modes, after setting alarm clock，Click the save icon in the upper right corner to exit，as show below：

Assembly Description

1. Insert the stainless steel pipe into the base, press a M3 screw nut into the nut slot, and then establish them with a PM3.0*25mm screw:

2. Insert the transmitter holder into the stainless steel pipe, establish them with a PM3.0*22mm screw and a M3 screw nut:

3. Insert the rain gauge holder onto the short side of the transmitter holder, establish them via a PM3.025mm screw and a M3 screw nut. Then install the rain gauge onto the rain gauge holder, and establish them with two PA3.08mm screws:

4. Press a M3 screw nut into the nut slot of the small side of the wind sensor holder, insert wind sensor holder onto the transmitter holder, establish them with a PM3.0*22mm screw:

5. Insert the wind direction component into the wind speed component, and then insert the wind direction RJ45 into the 623K hole of the wind speed component. Insert a M3 screw nut into the big side of the wind sensor holder, and then install the whole wind sensor onto the holder, establish them with a PM3.0*22mm:

6. Open the battery compartment, install the rechargeable batteries, then cover the battery door. Insert the whole transmitter onto the long side of the transmitter holder, and establish them with a PM3.0*18mm screw. At last, insert the wind speed wire RJ45 into the “WIND” 623K hole of the transmitter:

7. ① Put the rain gauge wire across the waterproof tower case, and then insert the RJ45 into the 623K hole of the solar component;
   ② Put the solar wire across the waterproof tower case, and then insert the RJ45 into the “RAIN” 623K hole of the transmitter;
   ③ Insert a M3 screw nut into the top nut slot of the waterproof tower case, then insert the solar component into the top of the waterproof tower case, establish them with a PM3.0*8mm screw (Note: insert the screw from the screw nut side of the solar component):

8. Suit the assembled waterproof tower case onto the assembled transmitter, and then suit the wires onto the slots of the transmitter holder

9. Suit four green plastic screw nuts into the base, and then establish the base and ground with four KA4.0*40mm screws：

10. Assembly sample diagram:

Feature

Receiver:

1. Temperature range: 0 ℃~60 ℃(32℉~140℉), resolution: 0.1℃, accuracy: ±1℃.
2. Humidity range: 20%~99%, resolution: 1%, accuracy : ±5%.
3. Pressure range: 300-1100hpa, resolution: 0.1 hpa, accuracy: ±3 hpa.(700-1100 hpa interval)
4. Alarm clock: lasts 2 minutes.
5. Working voltage: 3* AA1.5V voltage.
6. Battery life: About 6 months (battery quality and capacity determine the service time of the product).
7. External DC power supply or MINI USB power supply, DC block products can also supply DC power: DC 5V/500mA.
8. Low voltage detection: Battery icon flashes (battery voltage is lower 3.2V).

Transmitter

1. Temperature range: -40 ° C ~60 °C (-40 ° F ~140 °F), resolution: 0.1 ° C, accuracy: ±1 ° C.
2. Humidity range: 20%~99%, resolution: 1%, accuracy rate: ±5%.
3. Wind speed range: 0~50m/s, resolution: 0.1m /s, accuracy : 1 m/s (at wind speed <10m/s).
4. Rainfall range: 0~9999mm, rainfall resolution: 0.4mm(rainfall <1000mm), 1mm(rainfall >1000mm).
5. Data update: 40 seconds/time.
6. Working voltage: 2* AA1.5V voltage.
7. Battery life: Over 6 months.
8. Low voltage detection: Battery icon flashes (battery voltage is less than 2.4 V).
9. Waterproof level: IPX3

Attention

1. When the battery appears low voltage warning, it will cause flashing alarm, touch the button does not work, data received signal, please replace the battery in time. (Indoor machine: battery voltage is lower than 3.2V or so.
   Outdoor machine: battery voltage is lower than 2.4V or so)

2. No outdoor transmitter data can be received: Outdoor confirm product range, 433 MHZ wireless transmission to 100 meters can be measured without interference without sunscreen, check the battery, whether on the indoor and outdoor battery symbol flashing said electricity shortage, check whether outdoor fire board 40 seconds lamp shining time, RAIN and WIND line check board is wrong, not receive data in 3 minutes, power electricity repeated check.

3. Products and mobile phone time synchronization Settings: Open the APP, allowed to open the bluetooth, search to the product model click enter, see the product on the upper left corner will appear immediately bluetooth ID, with mobile phone for 10 seconds time synchronization, and automatically jump WiFi interface to enter the password after the connection is successful, each time will be switched on automatically update. (note: the phone APP cut by mistake with bluetooth pairing.)

4. No WiFi connection, no data or data update: Check the effective distance between WiFi and the device, check whether WiFi connection network is normal, upload data to the cloud once every 30 minutes after WiFi connection, and update data once every 30 minutes after APP reads data. (note: it is normal for the APP to read the cloud data for about 30 minutes different from the current mobile phone time.)

5. APP operation: Scan the QR code on the instruction manual or color box — select download APP– install APP– open APP to enable bluetooth — search product model and confirm — input WIFI password — check the current data after
   connection. (open the APP to allow bluetooth to be turned on, allow to open the phone positioning, and allow reading device storage.)

6. Outdoor solar power energy description: Solar panels do not charge the battery, when the solar panel collects enough electricity, to provide electricity to the transmitter to increase the battery life for a long time.
   QX20220915001

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>