astro 01107170 3200K LED Followspot Instruction Manual

astro 01107170 3200K LED Followspot

Thank you

Thank you for choosing a quality product from Luci della Ribalta srl. We trust our products and services meet your requirements, but should this not be the case please contact us directly using the attached feedback form to help us improve the quality of our service.
This spotlight has been manufactured with great care and left our factory in perfect conditions, but if it has been damaged in transport please contact your dealer in the first instance. A feedback form is appended. Our warranty covers all manufacturing and component defects for 2 years from the date you received the product.
Our products are designed for the use of professional technicians, and the instructions provided here ensure a safe and correct operation of this product. Luci della Ribalta srl will not accept any responsibility where damage has been caused to the product or persons through improper use of the product and/or non‐compliance with the regulations described herein.

IMPORTANT: Read these user instructions before using this lighting unit

The instructions given here ensure a safe and correct usage of this product. A user’s failure to comply with the installation, operating, maintenance and safety procedures mentioned in this manual, as well as those generally applicable to this lighting equipment, may cause the luminaire not to perform as expected.
Luci della Ribalta accepts no liability for direct, indirect, incidental, special or consequential damages resulting from the customer’s failure to follow the installation, operating, maintenance and safety procedures in this manual or those generally applicable to lighting equipments.
The limitation extends to damages for personal injury, property damage, loss of operations, loss of profits, loss of product or loss of time, whether incurred in by the customer, the customer’s employees or a third party.
Apart from the instructions given on this manual, all relevant safety and health standards of the appropriate EU Directives or the local safety and health standards of the country where the unit is installed, must be complied with.

IMPORTANT SAFETY NORMS

• This product is rated IP20 and is therefore designed for interior use only. For details on maximum ambient temperature, minimum distance from flammable objects and minimum distance from lit surface, please refer to the product label or the screen‐printed information to be found on the rear plate and front side of each luminaire.

• Continuous mains power is required for this spotlight as an internal dimmer controls the intensity via DMX or local rotary knob. Use of a phase control dimmed mains supply may damage the internal electronics.

• This product features fan‐assisted ventilation. Make sure you do not cover the fans or obstruct the air flow at any one time.

• Make sure the fans are working correctly. Should you detect even the slightest malfunction, switch the luminaire off and carry out the necessary servicing. Replace the fan if necessary.

• This product must be fitted with a front protection shield (wire guard or safety glass). Should this not be supplied as a standard accessory, please make sure you buy it separately and install it before using the product.

• There are no user serviceable parts in this product. Replacement of any internal component of this product must be carried out exclusively by professional personnel and only with original Luci della Ribalta srl components. Replacement of any part of the wiring system must comply with the original wiring diagram and with components identical or compatible with those originally fitted.

• This product must be fitted with a secondary fixing system such as a safety chain or bond.
  Should this not be supplied as a standard accessory, please make sure you buy it separately and install it before using the product.

• Installation of this product must be exclusively carried out by professional personnel in compliance with the safety norms in force in the country where the product is used.

• WARNING: DANGER OF ELECTRICAL SHOCK. DO NOT OPERATE ON LIVE EQUIPMENT
  Disconnect power before opening this fixture to access its light source or electronics. The replacement of the LED source can be carried out exclusively by professional personnel upon LDR’s written authorization and only with original Luci della Ribalta srl components. Failure to obtain the manufacturer’s authorization to carry out the replacement/repair, will immediately invalidate the product’s warranty.

• WARNING: EYE DAMAGE HAZARD
  Make sure this fixtures is installed so as to avoid prolonged direct staring at its operating light source (LED) from a distance of less then 7m / 23ft.

BOX CONTENTS

A. Standard followspot

• Astro followspot in the chosen model
• Separate mains power cable with PowerCon
• Ø29mm spigot for followspot
• Iris diaphragm

B. Kit followspot

• Astro f.spot in the chosen model in flight case
• Fitted colour‐changer unit
• Separate mains power cable with PowerCon
• Iris diaphragm ‐ Ø29mm spigot for followspot
• Iris diaphragm
• Black follow‐spot tripod

WEIGHT AND DIMENSIONS

ASTRO 100 3200K and 5600K
net weight: 10,1 kg + 1,2 kg colour changer gross weight: 11,6 kg packing dimensions: 84x32x32h cm

MOUNTING THE SPIGOT

A spigot is supplied in standard delivery for you to tripod‐mount your followspot.

• Make sure the tripod you are going to use can withstand the product load as indicated on the product’s label and here above
• Make sure the tripod you are going to use features a top aperture over 28mm dia.
• Remove the M12 nut and the washer from the spigot.
• Insert the spigot in the central hole of the yoke of the followspot from beneath the yoke.
• Add the plain screw and the M12 self‐ locking nut and tighten the nut with a suitable tool.
• Mount the followspot on the tripod.

MOUNTING THE COLOUR CHANGER (accessory, part nr. 20105103)

• This section only applies in case you bought the followspot and the colour changer separately. In case you bought a kit model the colour changer will be already fitted.
• Mount the colour filters on the colour changer unit. See relevant instructions supplied with the colour changer.
• At the front of the followspot, slacken the 3 cross‐head black M4 screws (two at the top angles, one at the bottom, left‐hand side angle) so that they remain inserted approximately half‐way through.
• Position the colour changer unit on the front plate of the follow spot, making sure that the colour levers are positioned on the left‐hand side of the follow spot when viewed from the front and hang it to the previously positioned screws.
• Release the colour filters of the colour changer by pressing the black, flat lever in order to have access to the screws
• Insert a Phillips screws driver at least 12cm long in each one of the holes provided at the front of the colour changer and tighten each screw
• Ensure the colour changer unit is secure, and all three screws are tight.

MOUNTING THE IRIS DIAPHRAGM ‐ supplied

The iris diaphragm supplied with the followspot has 20 leaves to size the beam from a maximum aperture of 68mm to a minimum of 5mm. A black‐out iris diaphragm is available to special order.

• Using a Phillips screw‐driver remove the two cross‐head screws from the sides of the iris plate.
• Slide the diaphragm in the gate area.
• Fix the iris in position by tightening the previously removed screws

Important notice: do not leave the iris closed for over 5 minutes while the LED is on

FAILURE TO COMPLY WITH THE ABOVE NOTICE MAY CAUSE THE IRIS AND THE FOLLOWSPOT TO SUFFER MAJOR HEAT DAMAGES AND WILL INVALIDATE THE PRODUCT WARRANTY

SHUTTER BLADES (accessory, part nr. R80208019 x 4)

Shutter blades are not supplied with the unit but are available as separate accessory. They are sold as single items and relevant part number is R80208019, 4 are required.

IMPORTANT NOTICE BEFORE THE INSTALLATION / INSTALLATION

This fixture is meant for tripod‐mount installation only. No hanging is allowed Before installing this fixture check its weight on the product label and the weight of each accessory you are adding and make sure the structure you are installing it to withstands the total weight. The mounting stirrup is designed to allow the spotlight to be fitted to a suitable tripod or pole.

CAUTION
DO NOT TURN THE LUMINAIRE UPSIDE‐DOWN AND MAKE SURE THE STIRRUP ALWAYS SITS DOWNWARDS

Note: the spotlight’s location must provide suitable ventilation for the LED module.

• If not supplied choose a suitable clamp and make sure it is correctly fixed and strongly tightened to the stirrup according to the clamp’s manufacturer’s instructions
• When tilting the unit make sure the knob blocking the stirrup is strongly tightened and that the luminaire can hold the desired tilt angle

WIRING

Before being connected to the mains power, this unit may need to be wired with a suitable plug if not already installed. Make sure the plug you are using is rated for the proper power load.

This fixture must be grounded
Ensure the plug conforms to the relevant EU/UL or local electrical standards

To perform a correct wiring, please note that the cores in this mains lead are colour‐coded as follows:
Ground: green + yellow – Neutral: blue ‐ Phase: brown

In case the colours of the wires do not correspond to the colour of the connection points on your plug, please proceed as follows:

• The green or green and yellow wire must be connected to the connection point marked with the letter E or with the symbol  **** or coloured in green or in green‐yellow.
• The blue wire must be connected to the connection point marked with the letter N or coloured in black
• The brown wire must be connected to the connection point marked with the letter L or coloured in red

Before you finally position this product for use, temporarily connect it to a properly fused power supply to check the unit works correctly.

VOLTAGE

Before operating this unit please refer to the product label mounted at the back of the luminaire to check you are operating with the correct voltage. The Astro 100 LED can be operated between 100V and 260 VAC.

FREQUENCY

Frequency on this product is automatically selected by the electronic PSU (50/60Hz)

CONNECT TO THE POWER SUPPLY

• Connect the unit to a continuous mains power source
• Make sure the power supply is protected by a suitable circuit breaker
• This fixture must be grounded

MECHANICAL OPERATION

Focus control: this fixture features a variable beam angle from 10° to 28° which can be controlled through the two control knobs on the right‐hand side of the lens‐tube.
The variable beam is modified by adjusting the front and rear zoom lenses in relation to each other.
The front lens defines the beam spread, the rear lens defines the focus degree of ‘softness’ or ‘hardness’ of the beam edge or shutters.
Gently turn the knobs anti‐clockwise until you have reached the desired size/focus of the beam in relation to the distance you are projecting at.
Turn the knobs clockwise and tightly close them so that the lenses are held in position at any tilt angle
Beam‐sizing: the size of the beam is controlled using the supplied iris diaphragm
Beam‐shaping: 4 accessory shutter blades (see chapter 7. Of this manual) can be fitted to shape the beam
Pan & Tilt control: this unit is fitted with a rear grab handle and a front side bar for an easy and safe control of the pan and tilt angle by the followspot’s operator.
The stirrup is factory‐balanced and fitted with a positive friction clamp controlled by a user‐friendly, effective lever‐knob. Turn the knob anticlockwise to release it, position the followspot at the desired tilt angle and turn the knob clockwise to hold the desired position.
Press the button at the top of the lever and keep it pressed while turning the lever if you need to change its position.
Make sure the knob is softly tightened at any time during operation

CONTROL FUNCTIONS AND OPERATION

OPERATION: LCD display for DMX address, system setup and status details.
POWER: power LED status indicator, red color. ON= power
DMX: DMX LED status indicator, green color. LED OFF = DMX OFF and manual control activated, LED ON =
DMX MODE activated with no DMX signal, FLASHING LED = receiving DMX
MENU: rotary switch selector to select and modify the operational modes. Turn left or right to navigate through the menu and press to select or to confirm
DMX IN: input DMX signal (pin1=0, pin2= DATA‐ , pin3=DATA+ ).
DMX OUT: Loop through DMX signal output
POWER IN: Mains power input
POWER OUT: Mains power output

MENU

There are thirteen different operation menus for the setting of the ASTRO 100 LED control functions. The rotary selector is used to adjust the settings and to navigate through the menu structure. Turn left or right to select the menu and push to access or to confirm the selected data or functions.

DMX OR MANUAL (Mode):

Select the LED control mode between DMX (factory setting) and manual. To change the control mode press once the rotary selector until an arrow (←) appears on the menu. Turn the selector to the right or the left to select the desired mode of operation and press to confirm your selection.

Tap the rotary selector and the LCD screen will display the mode status and the current value :

DMX ADDRESS (Addr):

It allows to select the initial DMX starting address to remotely control the LED functions. To change the initial DMX address press the rotary switch until an arrow appears, then turn to change to the desired DMX starting address. Press to confirm your selection. Factory setting is 001.

DIMMER RESOLUTION (8/16b):

The dimming resolution can be controlled at 8 bits from one DMX channel to 16 bits with 2 DMX channels.
Factory setting 8 Bit.

DMX FREQUENCY CONTROL (DMXCfg):

If turned ON it allows to remotely control the LED Frequency or the strobe speed through a dedicated DMX channel.
Factory setting OFF.

LOST DMX SIGNAL (DMXMem):

In case of signal failure this function allows to store in memory the last DMX value. Factory setting ON. Three options are available:

STROBE (Strobe):

This function enables to activate the strobe function. Factory setting DISABLE.

STROBE SPEED (SetStr) :

It allows to set the strobe speed. This menu is not active when the strobe function is disabled or when it is remotely controlled through DMX (required DMXCfg function enabled). Factory setting OPEN.

DIMMING CURVE (Curves)

This function allows to select a response curve for the ASTRO 100 LED. A choice of three curves is available:
LED‐HAL to reproduce halogen behaviour, square and linear. Factory setting LED‐HAL.

CUT OFF DIMMING RESPONSE (CutOff) :

This function allows to select an LED behaviour simulating a tungsten‐halogen lamp during the dimming cut off. Factory setting OFF.

DIMMING BEHAVIOUR (Smooth) :

This function allows to set the LED dimming response. Factory setting SLOW.

LED FREQUENCY ADJUSTMENT (Freq):

This function allows to adjust the LED frequency to avoid interference with TV cameras. The frequency can be adjusted from a selection of 13th different values between 2KHz to 460Hz. When DMXCfg function is enabled, the frequency is controlled through the dedicated DMX channel and this menu becomes inactive.
Factory setting 2kHz.

LCD SCREEN ILLUMINATION (BackL) :

This function allows to turn off the LCD backlight after 1’30” from last setting. Factory setting AutoOFF.

SOFTWARE VERSION AND TEMPERATURE CONTROL (V 1.0):

This function allows to visualize the software version and the LED temperature in °C.

PRO or BASIC CONTROL (ProBasic) :

The PRO‐BASIC control is a special function which allows to limit the access to the control menu. To activate this function turn OFF and ON the ASTRO 100 and press the rotary switch at power on. Select ProBasic with the rotary switch and press to access the menu.
Select :
PRO, to enable access to all the functions
BASIC, to limit access to functions 15.1 DMX or MANUAL MODE, 15.2 DMX ADDRESS and 15.13 Software version and temperature control
Factory setting PRO.

RESET

The RESET control is a special function which allows to RESET the product to factory settings. To activate this function turn OFF and ON the ASTRO 100 and press the rotary switch at power on. Select RESET with the rotary switch and press to RESET ASTRO 100 to factory settings.

CLEANING AND MAINTENANCE

To ensure maximum performance of the product, a regular maintenance service should be carried out. Please make sure the product is cold and disconnected from power supply when doing this.

General maintenance

• Clean all reflective parts such as lenses opening the product, if necessary.
• Check the lenses and replace any visibly damaged component.
• Clean air ducts and fans in order to allow a proper ventilation activity on the product.
• Check internal and external wiring and replace any cable which should be damaged by heat or mechanical agents.

Cleaning of optical components
LEDhouse lenses:

Open the lens compartment door by removing the two M4 cross head screws on the top of the ledhouse tube and slide the top cover free
Remove the condenser lenses assembly by removing the two M5 cross head screws.
Clean the lenses with a soft cloth and re‐position

Zoom lenses:
Slide the front zoom panels positioned at the bottom of the lens tube and clean with a soft cloth.

SPARE PARTS

All components are available as spare parts. We strongly recommend you always use original LDR components as spare parts. Please refer to our technical assistance should you need to order and/or replace any part of the unit.

WARRANTY

Our warranty covers all structural and manufacture defects for two years from the date you purchased this product. In case of complaints we strongly recommend you use the complaint form at the end of this manual or contact the local dealer who supplied the product to you. In any case please report the serial number of the product.
In case of complaints under warranty proof of purchase will have to be provided.

SUMMARY OF CONTROLS AND FUNCTIONS

#| function| description| available options| factoring setting
---|---|---|---|---
1| Mode| MANUAL or DMX control| MANUAL (controlled from the rotary switch) ‐ DMX| DMX
2| Addr| selects the DMX starting address other remotely controlled functions are assigned in sequence to the 1st assigned DMX address| from 000 ‐ 512| 001
3| 8/16 Bit| 8 or 16 Bit dimming resolution| 8 bits on 1 channel ‐ 16 bit on 2 channels| 8 Bit
4| DMXCfg| if enabled remotely controls the LED frequence and the strobe speed through a dedicated DMX

channel

| ENABLE ‐ DISABLE| DISABLE
5| DMXMem| sets the behaviour of the unit in case of DMX failure| ON=last DMX value ; OFF=80%
fade to 80% after 1,5 Sec ; OFF=0%| ON
6| Strobe| activates the strobe function| ENABLE ‐ DISABLE| DISABLE
7| SetStr| Selects the Strobe speed. This menu is inactive when the Strobe function is disabled or when it is remotely controlled through DMX (DMXCfg function enable)| OPEN = ON; SPEED = xx (select value from 01 slowest to 10 fastest); CLOSED = OFF| OPEN
8| Curves| selects the dimming curve| LED‐HAL ; SQUARE ; LINEAR| LED‐HAL
9| CutOff| replicates the halogen lamp dimming behaviour at cut off| FAST=NOT ACTIVE; SLOW=ACTIVE| SLOW
10| Smooth| dimmer response| OFF=Immediate response; SLOW=300ms; FAST=150ms| Smooth
11| Freq| sets the LED frequency. This menu is not active when DMXCfg is enabled| 12 Frequencies available (469Hz‐
610Hz‐762Hz‐939Hz‐1.1kHz‐
1.2kHz‐1.3kHz‐1.5kHz‐1.7kHz‐
2.0kHz‐2.4kHz and 3kHz)| 2kHz
12| BackL| LCD screen retro‐illumination| ON; AutoOFF=LCD light off after 1’30”| AutoOff
13| V 1.0| visualizes the software version and LED temperature| select the LED Temp in °C or F°| °C
SPECIAL FUNCTIONS: to activate these functions press the rotary switch at power‐on

#| function| description| available options| factoring setting
A| ProBasic| sets the operation modes. To activate this function press the rotary switch at power‐on| PRO=enable access to all the CETRA functions ‐ BASIC = limit the access to functions: 1 Mode, 2 Addr and 13 V 1,0| PRO
B| RESET| factory RESET| returns to factory setting|

DMX Charts

proportional (LTP) in 8 bit mode0‐65535 Light level values from 0 to 100%:
proportional (LTP)
2| Fine dimmer| Not Used (8 bit mode) in 16 bit mode
3| Strobe

Speed Available only if DMX Cfg ON (Off by default)

| 0‐20: Open
21‐40: Speed (slow)
41‐60: Speed
61‐80: Speed
81‐100: Speed
101‐120: Speed
121‐140: Speed
141‐160: Speed
161‐180: Speed
181‐200: Speed
201‐220: Speed (fast)
221‐240: Closed and reserved
241‐255: Closed
4| Frequency
Frequency Available only if DMX Cfg ON (Off by default) Note: for technical reasons, some frequencies may not be available on all products.| 0‐20: 3kHz
21‐40: 2.4kHz
41‐60: 2.0kHz
61‐80: 1.7kHz
81‐100: 1.5kHz
101‐120: 1.3kHz
121‐140: 1.2kHz
141‐160: 1.1kHz
161‐180: 939Hz
181‐200: 760Hz
201‐220: 610Hz
221‐240: 469Hz
241‐255: Reserved

CERTIFICATE OF CONFORMITY

We hereby declare, under our own responsibility, that the products listed here below:

ASTRO 100 plus LED LUMINAIRES
Standard models and all their variants

conform to to the following standards:

EN IEC 55015:2019 LIMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE CHARACTERISTICS OF ELECTRICAL LIGHTING AND SIMILAR EQUIPMENT
EN 61547: 2009 EQUIPMENT FOR GENERAL LIGHTING PURPOSES. EMC IMMUNITY REQUIREMENTS
EN 61000-3-2: 2018 ELECTROMAGNETIC COMPATIBILITY (EMC). PARTS 3-2: LIMITS -LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT UP TO AND INCLUDING 16 A PER PHASE) CLASS C
EN 61000-3-3: 2013+A LIMITATION OF VOLTAGE CHANGES, VOLTAGE FLUCTUATIONS AND FLICKER IN PUBLIC LOW-VOLTAGE SUPPLY SYSTEMS, FOR EQUIPMENT WITH RATED CURRENT ≤ 16 A PER PHASE AND NOT SUBJECT TO CONDITIONAL CONNECTION

FOLLOWING THE PROVISIONS OF EU ELECTROMAGNETIC COMPATIBILITY (EMC) DIRECTIVE 2014/30/EU

EN 60598-1: 2015+A1: 2018 LUMINARIES. GENERAL REQUIREMENTS AND TEST
EN 60598-2-17: 2018 LUMINARIES. PARTICULAR REQUIREMENTS. SPECIFICATION FOR LUMINARIES FOR STAGE LIGHTING, TELEVISION, FILM AND PHOTOGRAPHIC STUDIOS (OUTSIDE AND INDOOR
EN IEC 62031: 2020 LED MODULES FOR GENERAL LIGHTING SAFETY SPECIFICATIONS
EN 62493: 2015 ASSESSMENT OF LIGHTING EQUIPMENT RELATED TO HUMAN EXPOSURE TO ELECTROMAGNETIC FIELD
EN 62471: 2008; IEC/TR 62778: 2014 PHOTOBIOLOGICAL SAFETY OF LAMPS AND LAMP SYSTEMS

FOLLOWING THE PROVISIONS OF EU LOW VOLTAGE DIRECTIVE (LVD) 2014/35/EU

Directive 2002/96/EC (Waste Electrical and Electronic Equipment – WEEE): information for users.
This product complies with EU Directive 2002/96/EC.
The crossed-out wastebasket symbol on the appliance means that at the end of its useful lifespan, the product must be disposed of separately from ordinary household wastes. The user is responsible for delivering the appliance to an appropriate collection facility at the end of its useful lifespan. Appropriate separate collection to permit recycling, treatment and environmentally compatible disposal helps prevent negative impact on the environment and human health and promotes recycling of the materials making up the product. For more information on available collection facilities, contact your local waste collection service or the shop where you bought this appliance.

Luci della Ribalta srl, Via Berna 14, 46042 Castel Goffredo MN Italy – tel +39 0376 771777 – web www.ldr.it – email info@ldr.it
VAT registration # It01815640204 – REA MN 198438 – Authorized Exporter # IT/015/MN/11

References

• [ L.D.R. - Luci della Ribalta - ]

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>