Tongshi T1 Smart Watch User Guide
- June 14, 2024
- Tongshi
Table of Contents
smart watch
user’s Guide
T1 Smart Watch
Wear it properly
The bracelet is best worn after the ulnar styloid
Adjust the size of the wrist according to the adjustment hole; buckle the
wrist strap buckle.
The sensor should be close to the skin to avoid moving
Charge the bracelet
Use it for the first time to ensure that the battery is in normal condition.
If the power is not turned on normally, please connect the charger to charge
the device.
Install the bracelet app on your phone
Scan the QR code or go to the App Store, app download and install the app.
http://dw.ss-tjd.com/download/en4.html
System requirements: Android 5.0 and above; iOS9.0 and above; support for Bluetooth 4.0.
Device connection
- For the first use, you need to connect the APP for calibration. After the connection is successful, the bracelet will automatically synchronize the time.
- Turn on the Bluetooth switch of the mobile phone system → enter the app device module settings → click “Bind device, experience more features” to enter, it will automatically search for nearby Bluetooth devices on the bracelet, find and connect the bracelet device.
- After the pairing is successful, the APP will pop up a guide page. According to the instructions, jump to the mobile phone system Bluetooth search to find the watch Audio device and connect it. After the connection is successful, you can make / receive calls and listen to music (Note: If the mobile phone system Bluetooth has not been searched watch Audio equipment, please enter the Dual mode menu and set it to On, you cannot make calls without connecting the watch Audio equipment.)
- APP will automatically save the Bluetooth address of the bracelet, and the APP will open and run in the background, and will automatically search and connect the bracelet;
- Android phones use all notification permissions to read contact information and give the app background running in the phone settings.
Bracelet function description
- Slide down the standby page to enter the notification reminder, and slide up to enter the control center
- Swipe left or right on the standby page to cycle through the dials
- Bracelet reset device This function will clear all data of the bracelet (such as step counting)
- Switch to the heart rate three-in-one interface to start the test, heart rate three-in-one interface 60s timeout automatically off screen (heart rate and blood pressure need bracelet hardware support).
Clock interface
After synchronizing with the phone, the bracelet will automatically calibrate
the time;
Swipe left or right on the standby page to cycle through the dials
Step
Number of steps
Wear the bracelet and record the number of daily movement steps to view the
current real-time steps.
distance
The distance of motion is estimated based on the number of walking steps.
Calories
Estimate the calories burned based on the number of walking steps
Heart rate, blood pressure, blood oxygen three-in-one
After entering the heart rate three-in-one test interface for a few seconds,
the current heart rate, blood pressure, and blood oxygen test results are
displayed. This feature requires a wristband to support heart rate and blood
pressure sensors.
dial
Dial pad for making calls (note: the phone also needs to be connected to a
watch Audio device)
phone book
Add 8 commonly used contacts in the APP. After the bracelet is successfully
connected with the APP Bluetooth, the contacts can be displayed in the
bracelet phone book. Click the contact to make a call (Note: The phone needs
to be connected to a watch Audio device)
Music control
The bracelet can control the previous song and the next song, and pause /
start playback. (Note: watch Audio devices need to be connected to use this
feature phone)
Dual mode switch
This switch needs to be turned on for the phone to search for the watch Audio
device. If the phone is not connected to the watch Audio device within 5
minutes after the bracelet is turned on, the switch will be turned off
automatically, and it needs to be turned on manually when it is used again.
exercise more
All sports modes can record the calories and duration of skipping rope.
Sleep mode
When you fall asleep, the bracelet will automatically enter the sleep
monitoring mode; automatically detect your deep sleep / light sleep / wake up
all night, calculate your sleep quality; the wristband only shows the total
length of deep sleep / light sleep / sleep, APP end can View sleep data
details.
Note: Sleep data will be available when you wear your wristband and sleep will
be detected from 10:00 pm. Sleeping data for 3/4 hours can be synchronized to
the app while sleeping.
Information mode
Information menu can view the latest news content
Stopwatch function
Enter the stopwatch and click the start button to start timing, click the
pause button to stop, and click the reset button to clear the timing.
Custom dial
You need to connect to the APP to get the dial settings, you can choose the
recommended dial / default dial / album custom dial to synchronize to the
bracelet.
Stopwatch function
Enter the stopwatch and click the start button to start timing, click the
pause button to stop, and click the reset button to clear the timing.
Custom dial
You need to connect to the APP to get the dial settings, you can choose the
recommended dial / default dial / album custom dial to synchronize to the
bracelet.
APP function and settings
Personal information
Please set your personal information after entering the app.
Settings > Personal Information, you can set gender – age – height – weight –
distance
You can also set your daily goal steps to monitor daily completions.
Application push
SMS notification:
In the connected state, if the SMS reminder function is enabled, the
bracelet will vibrate when there is a text message.
Other reminders:
In the connected state, if this function is enabled, when there are
Messages such as WeChat, QQ, Facebook, etc., the bracelet will vibrate to
remind and display the content received by the app (You need to give the APP
permission to get system notifications, and the wristband can display 20-40
words).
Note: Incoming call reminder system is enabled by default, no switch
option (calls for incoming calls need to be connected to watch Audio device)
Other functions:
Turn on the vibration setting function, when there are calls, messages or
other reminders, the bracelet will vibrate. If it is off, the bracelet will
only have a screen reminder without shaking to avoid interruption.
Tips for Android users:
When using the reminder function, you need to set it to allow “LEFUN” to
run in the background; it is recommended to add “LEFUN” to the rights
management and open all permissions.
Alarm setting
In the connected state, 8 alarms can be set. After setting, it will be
synchronized to the bracelet; offline alarm is supported. After the
synchronization is successful, even if the APP is not connected, the bracelet
will be reminded according to the set time.
Looking for a bracelet
In the connected state, click the “Look for the bracelet” option and the
bracelet will vibrate.
Remote photography
In the connected state, start the photo from the wristband or the APP to
enter the remote camera interface, shake/turn the wrist/touch the bracelet,
and automatically take a photo after 3 seconds of counting down. Please allow
the APP to access the photo album to save the self-portrait photo.
Sedentary reminder
Set whether to enable the sedentary reminder function, you can set the
reminder interval, if you sit for a long time in the set time, the bracelet
will remind you.
Raise your hand to brighten
Turn this function on. When the wristband is in the state of the screen,
lift your wrist and turn the screen to yourself to light up the screen.
Do not disturb mode
Turn on the Do Not Disturb mode. You can set the Do not disturb time
period. During the set time period, the bracelet stops receiving notification
messages to avoid reminding messages.
Device reset
? reset will erase all data in the bracelet (such as step
is feature will erase data and remove device
| Equipment type | smart wristband | type of battery | Lithium polymer |
|---|---|---|---|
| Vibration motor | stand by | Synchronously | Bluetooth 4.0 |
| Operating temperature | -10°C-50°C | sensor | Lowpower acceleration sensor |
| System Requirements | 1059 or above / Android5.0 or above |
Precautions
- Bathing and swimming should not be worn.
- Please connect the bracelet when synchronizing data.
- Use the included charging cable to charge.
- Do not expose the handle ring to moisture for a long time, where the temperature is extremely high or extremely low.
- The flashover of the wristband restarts. Please check the memory information of the mobile phone to clear it and try again, or exit the APP and reopen it.
FCC Warnning: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, macaques harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.