Tacopet B0BX9DG99P Smart LED Flool Lamp User Manual
- June 14, 2024
- Tacopet
Table of Contents
Tacopet B0BX9DG99P Smart LED Flool Lamp User Manual
Download the APP
Scan the QR code below to download “Magic Home pro” APP in APP Store or Google
Play.
Install your smart light
Remove the bulb from its packaging and screw it into your light fixture. Then,
turn it on.
Connect your light
- Turn on Bluetooth.
- Run the newest App “Magic Home Pro” and Register/ Login your Magic Home account.
- Click “+” button on top right comer and choose the bulb which you want to connect. (If can’t found, reset your bulb)
- Connect device to Wi-Fi network. (Choose your router and login your password, ensure the router is 2.4GHZ
Parameters
5 Channels : RGB+CCT
Power: 7W/9W/10W
Light Luminous Flux : 600LM/800LM
Voltage:
AC 100-240V, 50/60HZ /AC 100-130V, 50/60HZ
/AC 190-240V, 50/60HZ
Working Temperature: -20-45°C
Lamp Socket: E26/E27/B22
Restore the factory setting
- Power on the bulb.
- Wait 3-5 seconds and then power off the bulb.
- At the end of the 4th time when you turn on the bulb, it will emit strobe for a few seconds, after that it will become fully bright at which point the reset is complete. Once you have reset the bulb, you should be able to see its wifi IP “LEDnet*** again under your mobile device’s wifi settings. (If not, please restart your wifi, wait for a while and you will see it).
FAQ
Scan the QR code below to read the electronic manual. Or open the APP’s menu
bar of the APP and click the FAQ to learn more
Instruction
Smart 2.4G remote controller
A.Pair the remote control:
After the lamp is powered on, press the power button for 5 seconds immediately
(within saconc). When the amp
flashes slowly for 3 times, it means the pairing is successful.
Pair The remote control
B. Remove the remote control:
After the bulb is powered on, press the power button for 5 seconds immediately
(within 3 seconds). When the bulb flashes for 3 times, it means the removing
is successful
Remove the remote control
-
One-to-many control
The remote control can be paired with multiple WiFi bulbs at the same time, and multiple WIFI bulbs can be controlled with one key without limitation.
Note: Please refer to the steps of pairing or removing the remote control
-
Many-to-one control
A single WIFI bulb can be paired with multiple remote. controls, and each remote control can control the same WiFi bulb separately. ( a single bulb can support up to 16 remote controls)
Note: Please refer to the steps of pairing or removing the remote control
How do I connect to Google Assistant?
Step 1: Creating your Magic Home cloud account.
In order to control your smart light with the Google Assistant or control them
remotely, you need to create a Magic Home cloud account and signed in.
Step 2: Add your light and modify the name.
Make sure there’s at least one smart light in device list, and enabled your
lights for remote control. In the “Home” page, long press on the light you
wish to rename.
Step 3: Add Home Control Action.
Add device in Home Control of the Home app. Select “Magic Home WiFI
Step 4: Login with your app account.
Enter your app account and password o finish the account linking. (Using your
Magic Home cloud account you used in step 1). Your device should be listed in
Home Control device List now.
Step 5: Control your light.
At this point, you’e all setup. You can now control your lights by issuing
voice commands.
Supported Commands:
Say “Ok Google” or “Hey Google”, then..
- Tum on slight name>
- Dim
- Brighten
- Set
to [50% ] - Dim/Brighteln
by[50% ] - Turn light name> [color]
- Turn on/off all the lights
- Is
on ?
Changing colors on your lights
- Blue
- Fuchsia
- Lavender
- Orange
- Salmon
- Turquoise
- Crimson
- Gold
- Lime
- Purple
- Sky Blue
- Violet
- Cyan
- Green
- Magenta
- Red
- Teal
- Yellow
For Scenes
- You can activate scenes by following voice commands:
- Hey Google activate {scene name}
- Hey Google turn on {scene name}
How do I connect to Alexa?
Step 1: Creating your Magic Home cloud account.
In order to control your smart light with the Amazon Echo or control them
remotely, you need to create a Magic Home cloud account and signed in.
Step 2: Add your light and modify the name.
Make sure there’s at least one smart light in device list, and enabled your
lights for remote control. In the “Home” page, long press on the light you
wish to rename.
Step 3: Enable Alexa Skill.
The next step is to download the Amazon Alexa app. Open the Amazon Alexa app
and under the skills section, search for the “Magic Home” skill.
Step 4: Login and Discover Devices.
Enable the skill and sign in using your Magic Home cloud account you used in
step 1. The next step is to discover your smart lights from the Alexa app. You
can say “Alexa, discover devices”. Once Alexa has completed discovering your
smart lights, they will appear in the Smart Home section of the Alexa app.
Step 5: Control your light.
At this point, you’re all setup. You can now control your lights by issuing
voice commands
Supported Commands:
These are some of the currently supported Alexa voice commands for the smart
light.
- Alexa, set [light name] to [0-100]%
- Alexa, turn [light name] on/off
- Alexa, dim/brighten [light name]
- Alexa, increase/decrease [light name] Alexa, set the [light name] light to red
- Alexa, change the [light name] to the color blue
For RGBW Light (Change to Warm White)
Alexa, set the [ight name] to warm white
For CCT or RGBCW Light (Change to Color temperature)
- Alexa, make the light name] warm white
- Alexa, change the [light name] to the cool white
- Alexa, set the [light name] to daylight
Changing colors on your lights
Color Options for Alexa control of your smart device
- Blue
- Fuchsia
- Lavender
- Orange
- Red
- Teal
- Crimson
- Gold
- Lime
- Pink
- Salmon
- Turquoise
- Cyan
- Green
- Magenta
- Purple
- Sky Blue
- Violet
- Yellow
For Scenes.
- ‘You can activate scenes by following voice commands:
- Alexa start (scene name)
- Alexa tum on {scene name}
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>