ezoo EZ-EXSP12 4K HDMI 2.0 1X2 Extender User Manual
- June 14, 2024
- ezoo
Table of Contents
ezoo EZ-EXSP12 4K HDMI 2.0 1X2 Extender
OVERVIEW
UTP HDMI Extender EZ-EXSP12 supports HDMI 2.0 4K@60Hz 4:4:4 8bit, HOCP 2.2; Supports PoE, bi-directional IR, bi-directional RS232 and EDID management, It provides distribution 3 of 3840 x 2160@60Hz 4:4:4 video, Two UTP outputs, one HDMI local loop output and Two-way IR up to 50m/165ft over a single Cat6a/7 cable. Simple cascade mode makes it easy to apply to sport bar, Education, church, digital signage and other environments.
FEATURES
- Two UTP output extend UHD HDMI signal to remote HDMI display up to 165ft/50m.
- Supports HDMI 2.0 4K@60Hz 4:4:4 8bit,HDCP 2.2
- EDID management.
- Supports HDMI 4K@60Hz 4:4:4 8bit, up to 165ft/50m.
- Support 3D, Support deep color 30bit, 36bit
- Supports Blue-Ray 24/50/60fs/HD-DVD/xvYCC
- Supports HDMI signal re-timing, never lose quality
- Supports PoE, one power adapter powers on TX and RX without the power supply, Supports bi-directional IR, either TV controls Blue-ray DVD, or DVD controls TV via IR remote; So easy to set up control system.
- Supports bi-directional RS232, easy to connect to control system.
- Dolby Digital Audio format, HDMI ports support Dolby Digital 7.1 CH Audio; DTS-HD Master Audio/Dolby-AC3/DSD/LPCM.
- Multiple easy installation, include metal mounting ear, HOOK & LOOP
- Plug and Play; No driver required; In stalls in minutes
SPECIFICATIONS
-
HDMI version: Uncompressed HDMI 2.0
-
HDCP version: HDCP2.2
-
HDMI resolution: 4K*2K/1080p/1080i/720p/576p/576i/480p/480i
-
Support video format: 24bit/30bit, 36bit deep color
-
Support audio format: Dolby true HD/DTS-HD/LPCM7.1/Dolby- AC3/DSD
-
Max bandwidth: 600MHz Max baud rate: 18Gbps
-
Input/Output TMDS signal: 0.5~1.5Volts p-p (TTL)
-
Input/Output DDC signal: 5 Volts p-p (TTL)
-
Max working current: 1.5A
-
Power adapter format: Input AC 100V-240V/ 50HZ,60HZ;
Output: DC12V/2A -
Operating Temperature range: -15 to +55°C
-
Operating Humidity range: 5 to 90%RH (No Condensation)
-
Dimension (L x W x H): TX:1309420(mm);RX:835822(mm)
-
Weight: 400g
Panel
INSTALLATION
- Connect HDMI cable from HDMI source devices to HDMI 1X2 Extender input.
- Connect network/Ethernet cable from UTP out {Transmitter) to UTP input (Receiver).
- Connect HDMI cable from HDMI output {Receiver) to HDMI input on your display.
EDID SETTING
EDID switch on the front panel of transmitter
EDID SETTING
4K7 .1| 4K@30Hz_ 4:3:3_7 .1C Hz_3D
4K5.1| 4K@6 0Hz_4:4:4_5.1C Hz_3D
COPY| LEARNING EDID FROM HDMI OUT
HDCP SETTING
| Test mode | Strip out HDCP(Default) |
|---|---|
| Normal mode | HDCP1.4/ 2.2 pass through |
| Scaler 1080P | Downscaling from 4K to1080P |
TROUBLESHOOTING
- POWER: Make sure all devices are powered on.
- Make DVD PLAYER 24P/24Hz ON.
- DEVICES: Make sure picture can be shown normally when connecting HDMI source to display devices directly.
- HDMI CABLE: Plug in and out HDMI 2.0 cable or change another HDMI cable. When transmit HDMI 4K@60Hz (4:4:4) signal,HDMI 2.0 certificated cables is required.
- NETWORK CABLE:
- Please use Cat5e/6a/7 cable, don’t suggest use Cats.
- Make sure CatX cable is less than 165ft.
- Make sure the two connectors of one CatX cable are same standard (EIA/TIA 568B).
- COMPATIBILITY: Please test other source and display devices to determine whether it is a compatibility issue.
- IR SIGNAL: Make sure the IR cables are correctly installed according to the diagram above. (IR Bi-direction Control)
- Check if the IR emitter head is secured over the center of the IR window of source device. This position maybe discrepant if you use different sources, try to adjust the position if the signal is weak. (or you can refer to the user manual of your source device to confirm the exact position of IR window)
- Pay attention to the control angle and distance as below: The control signal will be better when your controller is pointed at the IR receiver head directly.
PACKING LIST
- HDMI1X2 Extender Transmitter x1
- HDMI1X2 Extender Receiver x2
- Power Adapter x1
- IR Emitter x1
- IR Receiver x1
- Mounting Ear x2
- HOOK & LOOP x2
- Reusable Cable Tie x2
- User Manual x1
NOTES
Please use this machine based on below instructions to keep longer lifetime.
- The machine should be placed at the spot far away from the Damp, High Temperature, Dusty, Erosive, and Oxidant environment.
- All parts will be free from the strong shake, hit, fall.
- Touching the device with the wet hands is prohibited.
- Please turn power off when machine is not used for long time.
- Please do not open the cover and do not touch the inside parts.
- Please use the original factory power adaptor.
- Before power on, please check the connection cable carefully. And make sure that all interfaces are normally connected.
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. EZCOO TECHNOLOGY INC. assumes no responsibility for any infringement of patents or other rights of third parties which may result from its use. EZCOO TECHNOLOGY INC. assumes no responsibility for any inaccuracies that may be contained in this document. EZCOO TECHNOLOGY INC. also makes no commitment to update or to keep current the information contained in this document. EZCOO TECHNOLOGY INC. reserves the right to make improvements to this document and/or product at any time and without notice.
Customer Support
CONTACTS
When you need any technical assistance, please send e-mail to ezcoousa@easycoolav.com | support@easycoolav.com