Licwshi SL01 Lumen Solar Light Instruction Manual

Licwshi SL01 Lumen Solar Light Instruction Manual

Specifications

| | | |
---|---|---|---|---
Model| SL01/SLO6| SLO2| SL03/SLO4| SLO5
Shel material| Aluminum cloy| Aluminum alloy| Aluminum cloy| PC+ABS
Solar panels| 5V 3.2W| 5V 1.5W| 5V 3.2W| 5V 3.2W
Lithium iron phosphate battery| 3.2V 4500mAh| 3.2V 1500mAh| 3.2V 4500mAh| 3.2V 4500mAh
Maximum voltage| 3.65V| 3.65V| 3.65V| 3.65V
Minimum voltage| 2.65V| 2.65V| 2.65V| 2.65V
Working current| 30-1900mA| 30-800mA| 30-1900mA| 30-1800mA
Power| 6.8W| 3.5W| 6.8W| 6.8W
LED quantites| 48PCS| 24PCS| 46PCS| 48PCS
Detection angle| 0-360°| 0-360°| 0-120°| 0-120°
Charging time| Sun exposure time is greater than 6 hours| 8 hours
Detection distance| 17-33ft (5-10m)| 17-26ft (5-8m)
LED specifications| SMD 2835 29-30Im                4000/6000k|
Waterproof grade| 1P65
Recommended installation height| 7-10ft (2-3m)

Installation steps:

Please charge the

1. Press the button product for 6 hours before use. for 5 seconds to start the circuit, and then select the desired lighting mode.
   

2. Non-foldable model : Nail two screws on the wall and hang the product directly.
   Foldable model : Fix the bracket with two screws and lock the product with screws
   

Application Methods:

First, completely shut out the solar panels or put it down on the desktop. Then press the button for 5 seconds to start the lamp. Enter the first operating mode after starting. Each press of the button will change the operating modes with the lights flickering at the same time. The circulatory switchover of operating
modes is as follows:

1. Micro-mode+ Induction mode
   When someone comes, the sensor triggers circuit to start high light; the light will dim after someone leaving for 15 seconds. (SL05: 30 seconds) (Firstly recommended to use)

2. Induction mode
   When someone comes, the sensor triggers circuit to start the high light; the light will be turned off after someone leaving for 15 seconds. (SL05: 30 seconds) (Use in the places with short lighting time)

3. Always light mode
   It will always light at night with no induction function. (Used in special places)

4. Emergency light mode (Continuous high brightness 30 minutes turn off-press 5 seconds to restart) Commonly use for emergency lighting, such as power failure and night activities. The timing of emergency light mode is 30 minutes. The solar panels should be restarted or illuminated after the lights off. (Note: SL05 high light until the electricity runs out)

5. Shutdown

Additional remarks:

1. Please attention: The time of sun exposure to solar panels has close relationship with the local weather conditions, installation site and direction, which will directly influence the charging effect.
2. The service life of lithium iron phosphate battery is more than five years, Therefore, there is no need to replace the battery in use. The product should be disposed appropriately because of the internal battery. Never put it into the fire to escape 3 from the danger of explosion.
3. The lampshade is made of plastic raw materials, therefore, it will be broken when littered or dropped. .
4. The sensing distance is affected by the temperature difference. In winter, the temperature difference is 4 large and the sensing distance is relatively long; in summer, the temperature difference is small and the sensing distance is shortened. (Applicable to infrared sensors solar lights)

MADE IN CHINA

Documents / Resources

| Licwshi SL01 Lumen Solar Light [pdf] Instruction Manual
SL01 Lumen Solar Light, SL01, Lumen Solar Light, Solar Light, Light
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>