Blukar K9751 Car Phone Holder User Guide

Blukar K9751 Car Phone Holder

Welcome
Thank you for purchasing Blukar products. In order to ensure the best performance and safety, please read this user manual carefully and save it for future reference. If you need any additional assistance, please contact our customer support team or send us an email to support@blu- kartech.com.

Package Contents

• 1 x Car Holder
• 1 x Long Arm Base
• 1 × 3M Dashboard Pad
• 1 x Air Vent Base

Specifications

• Material ABS+ silicone + metal +PC
• Applicable Size 4.7 -6.7 inch
• Applicable Places windshield/dashboard/car air outlet

Structure Picture

1. Silicone Pads
2. Fixed Nut
3. Clamp Arms
4. Quick Release Button
5. Hook clip
6. Adjustment knob
7. Ball Joint
8. Extendable Arm Adjusting Nut
9. Telescopic Arm
10. Suction Cup Lock
11. Extendable Arm Retaining Nut
12. Suction Cup
13. 3M Dashboard Pad

Long Arm Base Installation Steps

1. Loosen the fixed nut completely, let the ball joint through the fixed nut (The thread must face the groove) and push it to the groove behind the car holder firmly.
2. Tighten the fixed nut.
3. Use a wet cloth to clean the place (windshield or dashboard) where the car bracket needs to be installed, and then wait for it to dry.
4. As shown, push the suction cup lock up until it is fully open.
5. Attach the suction cup on the windshield/dashboard. Press firmly on the suction cup, then press the suction cup lock to lock it.
6. If you secure the car holder on the dashboard, please use it with the 3M dashboard pad. Please first stick the 3M dashboard pad on the dashboard. (Tear off the red protective sticker. Stick the 3M dashboard pad on the dashboard and press it firmly for over 1 minute to make sure it is properly attached.) Then install the car holder on the 3M dashboard pad and secure the suction cup in the same way as step 4 and step 5.
7. Adjust the angle of the car holder to fit the sight line. (Twist the extendable arm adjusting nut to adjust the length of the arms. Twist the extendable arm retaining nut to change the angle of the arms.)

Air Vent Base Installation Steps

1. Loosen the fixed nut completely, let the ball joint through the fixed nut and push it to the groove behind the car holder.
2. Tighten the fixed nut.
3. Turn the adjustment knob to adjust the length of the hook clip, find the right position (car vent blade) insert the car holder, hook the car vent blade and turn the adjustment knob to tighten the hook clip and fix it on the car vent blade. (Please do not over rotate to avoid damaging the car vent blade.)
4. Adjust the angle of the car holder to fit your sight.

Using Steps

1. Pressing the quick release button, the clip arms will automatically pop open.
2. Place the phone and push the clip arms at both ends to tighten the clip arms and hold the phone firmly.
3. After use, press the quick release button again to open the clip arm and take out the phone.

Suction Cup Use Note

1. When using the suction cup, do not stick it on a curved surface, surface with plush cloth or uneven surface. It would not be securely attached.
2. It is not recommended to attach the suction cup to leathers, walls or glass fiber surfaces, since the suction cup is designed with strong suction power.
3. The 3M dashboard pad can only be used one time. Once stick, it is hard to remove. Once removed, it cannot be used again. Please choose the appropriate position on the dashboard to install the 3M dashboard pad.
4. If the suction cup is frequently used in high temperature, low temperature or humid conditions, the suction will not stick as firm (Please avoid direct exposure to the sun).

Attention

1. Please install the car holder on a suitable place before starting driving navigation, do not operate and adjust the car holder during driving.
2. Do not install the car holder on a place which will influence the operation of airbag and driving.
3. Keep the car holder away from children.

Blukar
For any information or questions,please contact us anytime at:

• TEL: 1-800-360-5881
• EMAIL: support@blukartech.com.
• WEBSITE: www.blukartech.com.

© Shenzhen Teng Xun Zhan Yi Technology Co., Ltd. All rights reserved.

• Product Name: Car Phone Holder
• Model: K9751
• Manufacturer: Shenzhen Teng Xun Zhan Yi Technology Co., Ltd.
• Manufacturer Address: Room 302, Building 8, Yunli Intelligent Park, Fada Road, Bantian Street, Longgang District, Shenzhen, Guangdong, China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>