CISCO Codec Pro Flexible Room Device Installation Guide
- June 14, 2024
- Cisco
Table of Contents
CISCO Codec Pro Flexible Room Device
Box contents
No
power cord option for Codec Pro: When the optional power cord is not ordered
with the system, the customer is responsible for selecting the appropriate
power cord to be used with this product. Using a non-compatible power cord
with this product may result with electrical safety hazard. For orders to be
delivered to Argentina, Brazil and Japan, appropriate power cord must be
ordered with the system.
- Rating of the power cable: 10 A, 250 V
- Power connector: EL 701B (IEC 60320/C13)
Camera options for Codec Pro
This guide describes the installation of Codec Pro with SpeakerTrack 60 camera.
- For instructions on how to assemble the SpeakerTrack 60 camera, see Cisco TelePresence SpeakerTrack 60 Installation Guide.
- For installation of Codec Pro with Quad Camera, see Cisco Room Kit Pro Installation Guide.
- For installation of Codec Pro with Precision 60 camera, see Cisco Room Kit Pro Precision 60 Installation Guide.
- For installation of Codec Pro with PTZ 12 camera, see Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 camera guide.
- For installation of Codec Pro with PTZ 4K camera, see Cisco Room Kit Pro PTZ 4K installation guide.
Can be ordered separately
- Wall mounting bracket for the Precision 60 or PTZ 4K camera.
- Ceiling mount for the PTZ 4K camera.
- Cisco table or ceiling microphone.
- HDMI and Ethernet cables. We recommend cables from Cisco. Use certified HDMI cables for the cameras and presentation sources (High Speed HDMI 1.4b) and for the screens (Premium High Speed HDMI). You need Ethernet cables for camera control and network (not required if using Wi-Fi).
Ventilation
Do not block any ventilation openings on the codec. Minimum 10 cm / 4 ” free
space in front and rear side of the unit. Minimum 4.5 cm / 1.7 ” free space
below the codec and an adjacent rack-mounted component.
Mount the codec in a rack (optional)
You can mount the rack ears so that the connector panel is facing forward or
backward.
-
Connect the antennas to the codec (for radio version only)
-
Connect the codec cables
-
Connect the SpeakerTrack 60 cables
Always use the provided power cable and adapter (12 VDC, minimum 5 A).
-
Turn on the codec
Power (100-240 VAC, 50/60 Hz)- Always use the provided power cable. Or use a power cable that meets the requirements of the power specification of the codec.
- Keep the power plug and outlet easily accessible in case you need to disconnect the device from power.
- This device is designed for connection to TN and IT power systems.
- Network connectivity: Use either Ethernet LAN or Wi-Fi. Non-radio devices, which have the letters ‘NR’ in their product identifier (PID), don’t support Wi-Fi.
-
Complete the software setup
- Turn on the screen. See the user documentation for the screen if HDMI input must be set manually.
- The system powers up automatically. If the system doesn’t power up, check the power switch on the codec and the camera.
- When you see the Welcome screen, follow the instructions to complete the setup.
- We recommend that you upgrade the software on your Codec Pro before putting it to use. See the Administrator Guide for the codec: https://www.cisco.com/go/roomkit-docs
Cisco Codec Pro
- A. Antenna connector
- B. 6 × Line outputs (Euroblock, 3.5 mm)
- C. 8 × Microphone/Line inputs (Euroblock, 3.5 mm)
- D. GPIO port (Euroblock, 3.5 mm)
- E. COM port (Euroblock, 3.5 mm)
- F. Antenna connector
- G. Ground (Protective earth)
- H. Main power input (1.3 – 0.6 A, 100-240 V ac, 50/60 Hz)
- I. 2 × HDMI outputs with audio and video (Connector 1-2), 4Kp60
- J. HDMI output with audio and video (Connector 3), 4Kp30
- K. 2 × Camera inputs (HDMI, Connector 1-2), 1080p60
- L. 3 × HDMI inputs with audio and video (Connector 3-5), 4Kp30
- M. Camera input (3G-SDI / HD-SDI, Connector 6), 1080p60, HD-BNC, 75 Ω
- N. 2 × USB 2.0, type A
- O. USB 2.0, type B
- P. Maintenance (micro USB)
- Q. Factory reset
- R. Network (Ethernet) 1Gb
- S. 2 × Camera control (Ethernet)
- T. Ethernet PoE – Internal network port for PoE device
- U. Touch panel (user interface, Ethernet PoE)
- V. Status LED
- W. Power On/Off
Cisco TelePresence SpeakerTrack 60
Camera connector panel
SpeakerTrack connector panel
- A. Video (3G-SDI ), 1080p60 *
- B. Not in use
- C. HDMI output, 1080p60
- D. Factory reset
- E. Power input (12 Vdc, 2.5 A)
- F. Camera control (Ethernet)
- G. Power to camera right
- H. Power to camera left
- I. Power input (12 Vdc, 6.5 A)
- J. Camera control, camera right (Ethernet)
- K. Camera control, camera left (Ethernet)
- L. Network, from codec (Ethernet)
- M. Maintenance (micro USB)
- N. Euroblock, 3.5 mm (not in use)
- O. Microphone, internal cables from the microphone panel (Euroblock, 3.5 mm)
- P. Cinch connector (not in use)
- Q. Factory reset, * pin hole at the bottom of the unit
Visit these websites to learn more about your device.
help.webex.com
cs.co/mtrdevice-docs
cisco.com/go/room-docs
cs.co/webexadoption
projectworkplace.cisco.com
Room Kit Pro Data Sheet
See the product data sheet for more information on ordering accessories,
cables, and spare parts.Cisco Systems Inc.
Corporate Headquarters
170 West Tasman Dr.
San Jose, CA 95134
USA
https://www.cisco.com/go/offices
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco
and/or its affiliates in the U.S. and other countries. To view a list of Cisco
trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party
trademarks mentioned are the property of their respective owners. The use of
the word partner does not imply a partnership relationship between Cisco and
any other company. (1110R)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>